ADVANTECH AIMB-706 LGA1151 Intel ATX with Dual Display, SAT 3.0, USB 3.1, DDR4 User Manual

AIMB-706 LGA1151 Intel® Core™ i7/i5/i3 ATX with
Dual Display, SATA 3.0, USB 3.1, DDR4
Startup Manual

Packing List

Before you begin installing your card, please make sure that
the following items have been shipped:
• 1 x AIMB-706 Startup Manual
• 2 x Serial ATA HDD data cables
• 1 x Serial ATA HDD power cables
• 1 x I/O port bracket
If any of these items are missing or damaged, please contact your distributor or sales representative immediately.

Note: Acrobat Reader is required to view any PDF file. Acrobat Reader can be downloaded at: www.adobe.com/Products/acrobat/readstep2.html (Acrobat is a trademark of Adobe)

Specifications

Standard Functions
• CPU: LGA1151 socket supporting 8th/9th generation Intel® Core™ i7/i5/i3/Pentium/Celeron processor.
Note:

1. Intel 8th/9th generation processors only support Windows 10 (64-bit).
2. BIOS version V2.XX can support both 8th and 9th generation processors while BIOS version V1.XX can only support 8th generation processors.

•  BIOS: AMI 128 Mbit SPI BIOS.

•  Chipset: Intel® H310 PCH.

• System Memory: Up to 32 GB in two 288-pin DIMM sockets supporting dual-channel DDR4 2400/2666 SDRAM. AIMB-706 supports non-ECC unbuffered DIMMs and does not support any memory configuration that mixes non-ECC with ECC unbuffered DIMMs.
  Note: Due to the inherent limitations of the PC architecture, the system may not fully detect 32 GB RAM when 32 GB RAM is installed.

• SATA Interface: Four onboard Serial ATA 3.0 connectors support data transmission rates up to 600 MB/s. All four SATA 3.0 ports support Advanced Host Controller

Interface (AHCI) technology.

• PCIe and PCI Slot: 1 PCIe x16 expansion slot, 1 PCIe x4 expansion slot, 5 PCI slots 32-bit/33 MHz PCI 2.2 compliant.
• LPC Interface: Advantech-designed LPC connector supports TPM module and COM port extension module.
•  Serial Port: Up to six serial ports: COMD1, COMD2 and COM4 ~ 6 are RS-232; COM3 is RS-232/422/485 with  jumper and BIOS menu options.
• Parallel Port: One parallel port, which supports SPP/ EPP/ECP mode.
•  Keyboard/Mouse Connector: Supports standard PS/2 keyboard and mouse.
• Watchdog Timer: 255-sec timer level intervals.
• USB 3.1/2.0: 4 USB 3.1 Gen 1 ports (2 rear, 2 via header), 5 USB 2.0 ports (2 rear, 2 via header, 1 internal Type-A).

Graphic Interface

• Chipset: CPU integrated graphics controller.
• Display Memory: 1 GB maximum shared memory with 2 GB and above system memory installed.
• DVI-D: Resolution up to 1920 x 1200 @ 60 Hz refresh rate.
• VGA: Resolution up to 1920 x 1200 @ 60 Hz refresh rate.

Ethernet Interface

• Interface: 10/100/1000 Mbps.

• Controller: LAN1: Intel ® I219-V; LAN2 (G2 sku only): Intel ® I211-AT.
  Mechanical and Environmental

• Dimensions (L x W): 304.8 x 244 mm (12” x 9.6”)

• Power Supply Voltage: +3.3 V, ±5 V, ±12 V, +5 Vsb

• Power Consumption: Intel Core i7-8700 3.2 GHz; DDR4 16GB x 2 Maximum: +3.3 V at 2.74 A, +5 V at 3.5 A, +12 V at 5.92 A, +5 Vsb at 0.05 A, -5 V at 0.01 A, -12 V at  0.08 A

• Operating Temperature: 0 ~ 60° C (depending on CPU)

• Weight of Board: 0.7 kg (1.54 lb)

Jumpers and Connectors

The board has a number of jumpers that allow you to configure your system to suit your application.
The table below lists the function of each jumper and connector.

(ATXJAT) System off: off (AT/ATX)
JFP2| External speaker / HDD LED con­nector / SMBus connector
JFPI| Power switch/reset connector
AUD101.AUD102| Audio connector (Line Out. Mic In)
VOLT’| Alarm board power connector
JCASEI| Case open connector
LANLEDI| Front panel LAN indicator connector
SATAO – SATA3| Serial ATA 3.0 port
PC11| PCI slot
PCl2| PCI slot
PCI3| PCI slot
PCI4| PCI slot
Connector I -Wove| List
---|---
Label| Function
LPTI| Parallel port. supporting SPP/EPP/ ECP mode
LAN1| LAN1
LAN2| LAN2 (G2 sku only)
USB3CI| USB 3.1 Gen 1 port 1. 2
USB3H1| USB 3.1 Gen 1 port 1. 2 (20-pin header)
USB2C1| USB 2.0 port 1. 2
USB2A1| USB 2.0 port (internal Type-A)
USB2H1| USB 2.0 port 1. 2 (10-pin header)
VGAltDVII| VGA connector / DVI-D connector (DVII for G2 sku only)
COMD1+COMD2| Serial port: RS-232 (DB-9 con­nector)
COM4 – COMB| Serial port: RS-232 (9-pin header. G2 sku only)
COM3| Serial port: RS-232/4221485 (9-pin header. G2 sku only)
KBMS1| PS/2 keyboard and mouse con­nector
KBMS2| External keyboard and mouse con­nector (6-pin header)
CPUFAN1| CPU fan connector (4-pin)
SVSFAN1 – SVSFAN3| System fan connector (4-pin)
JFP3| Keyboard lock and power LED Suspend: fast flash (ATX/AT) System on: on (ATXJAT) System off: off (AT/ATX)
JFP2| External speaker / HDD LED con­nector / SMBus connector
JFPI| Power switch/reset connector
AUD101.AUD102| Audio connector (Line Out. Mic In)
VOLT’| Alarm board power connector
JCASEI| Case open connector
LANLEDI| Front panel LAN indicator connector
SATAO – SATA3| Serial ATA 3.0 port
PC11| PCI slot
PCl2| PCI slot
PCI3| PCI slot
PCI4| PCI slot
JCMOS1: CMOS clear
JME1: Intel ME update

Closed Pins| Result
2-Jan| Keep CMOS data
Enable ME to update
3-Feb| Clear CMOS data
Disable ME update

• Default

JWDT1+JOBS1: Watchdog timer output and OBS alarm

Closed Pins| Result
2-4, 8-10| Watchdog timer disable (2-4)
OBS beep (8-10)
4-6, 8-10| *Watchdog timer reset (4-6)
OBS beep (8-10)

• Default

PSON1: ATX/AT mode selection

Closed Pins| Result
1-2| AT mode
2-3| *ATX mode

• Default

JUSB_1 (rear USB), JUSB_2 (onboard USB): USB power source switch between +5V and +5V_DUAL

Closed Pins| Result
1-2| *USB +5V_DUAL power
2-3| USB +5V power

• Default

JSETCOM3: COM3 RS-232/422/485 jumper setting

Closed Pins| Result
5-6, 7-9, 8-10, 13-15, 14-16| *RS-232
3-4, 9-11, 10-12, 15-17,  16-18| RS-422
1-2, 9-11, 10-12, 15-17,  16-18| RS-485

• Default

Note: While RS-485 is selected, it is necessary to change device mode to RS-485 for further choice of auto flow control under the BIOS menu. Please refer to Chapter 3.2.2.10 of the user manual for further settings.

JT1(TX signal), JR1(RX signal): COM3 RS-422/485

termination resistor

Closed Pins| Result
1-2| Disable termination
2-3| *Enable termination

• Default

JFV1: VGA dummy load setting

Closed Pins| Result
1-2| Disable termination
2-3| *Enable termination

• Default

Declaration of Conformity

This device complies with the requirements in Part 15 of the FCC rules. Operation is subject to the following two conditions:

1.  This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
   Caution! The computer is supplied with a battery-powered real-time clock circuit. There is a danger of explosion if the battery is incorrectly replaced. Replace only with same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer’s instructions.

Board Layout

4 AIMB-706 Startup Manual

For more information on this and other Advantech products, please visit our website at: http://www.advantech.com

http://www.advantech.com

For technical support and service, please visit our support website for AIMB-706 at: http://advt.ch/aimb706spt 

http://advt.ch/aimb706spt

Register your products on our website and get 2 months extra warranty for Free at: http://www.register.advantech.com 

http://www.register.advantech.com

This manual is for the AIMB-706 series Rev. A1.
Part No. 2001070611
Printed in China
2nd Edition
August 2019

References

• Advantech - industrial computer , embedded computer, industrial automation, industrial motherboard, network security appliance, digital video surveillance, panel PC, industrial IO.
• Advantech Co-Creating the Future of the IoT World
• register.advantech.com

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>