CAMBRIDGE AUDIO AXA35 Integrated Amplifier Instruction Manual

: June 4, 2024
: Cambridge Audio

Table of Contents

Important safety instructions
Rear panel connections
Front panel controls
Remote Control
Connections
Operating Instructions
Technical Specifications
Troubleshooting
Documents / Resources

AXA35 Integrated Amplifier
Instruction Manual

AXA35
INTEGRATED AMPLIFIER

This guide is designed to make installing and using this product as easy as possible. Information in this document has been carefully checked for accuracy at the time of printing;
however, Cambridge Audio’s policy is one of continuous improvement, therefore design and specifications are subject to change without prior notice.
This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means, in any form, without prior written permission of the manufacturer. All trademarks and registered trademarks are the property of their respective owners.
© Copyright Cambridge Audio Ltd 2018.
Make sure you register your product at:
WWW.CAMBRIDGEAUDIO.COM/REGISTER
For upcoming news on future products, software updates, and exclusive offers.

Important safety instructions

For your own safety please read the following important safety instructions carefully before attempting to connect this unit to the mains power supply. They will also enable you to get the best performance from and prolong the life of the unit:

Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with a dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for the replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use with only the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as the power-supply cord or plug having been damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

WARNING:

Do not place the unit in an enclosed space; if you wish to place the unit on a shelf, use the top shelf to allow maximum ventilation. Do not put any objects on top of this unit. Do not situate it on a rug or other soft surface and do not obstruct any air inlets or outlet grilles. Do not cover the ventilation grilles with items such as newspapers, tablecloths, curtains, etc.
To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. This unit must not be used near water or exposed to dripping or splashing water or other liquids. No objects filled with liquid, such as vases, shall be placed on the unit.
Danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type.
The battery (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire, or the like.
The unit must be installed in a manner that makes disconnection of the mains plug from the mains socket outlet (or appliance connector from the rear of the unit) possible. Where the mains plug is used as the disconnect device, the disconnect device shall remain readily operable.
Please refer to the information on the exterior rear panel for electrical and safety information before installing or operating the apparatus.
Only use the main cord supplied with this unit.
Use of the apparatus in tropical climates – The equipment shall be used at a maximum of 45 degrees C ambient temperature.
The unit is of Class 1 construction and must be connected to a mains socket outlet with a protective earthing connection.

The lightning flash with the arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of un-insulated ‘dangerous voltage’ within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance instructions in the service literature relevant to this appliance.

WEEE SYMBOL
The crossed-out wheeled bin is the European Union symbol for indicating a separate collection of electrical and electronic equipment. This product contains electrical and electronic equipment which should be reused, recycled or recovered and should not be disposed of with unsorted regular waste. Please return the unit or contact the authorized dealer from whom you purchased this product for more information.

CE MARK
This product complies with European Low Voltage (2014/35/EU), Electromagnetic Compatibility (2014/30/EU), and Environmentally- friendly design of Energy- related Products (2009/125/EC) Directives when used and installed according to this instruction manual. For continued compliance, only Cambridge Audio accessories should be used with this product and servicing must be referred to qualified service personnel.

RCM (REGULATORY COMPLIANCE MARK)
This product meets Australia, New Zealand Safety, EMC and Radio Communications requirements of the ERAC and ACMA.
FEDERAL COMMUNICATIONS COMMISSION NOTICE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the distance between the equipment and the receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

SUPPLIER’S DECLARATION OF CONFORMITY (SDOC)
Equipment: Integrated Amplifier
Model: AXA35
Trademark: Cambridge Audio
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The responsible party in US:
Company name: Audio Partnership LLC
Address: 1913 N Milwaukee Ave. Chicago, IL 60647
Phone: 312-636-4817
Legal Representative Person: Gregg Chopper
Signature:

VENTILATION
Important! The unit will become hot when in use. Do not stack multiple units on top of each other.
Ensure that small objects do not fall through any ventilation grille. If this happens, switch off immediately, disconnect from the mains supply and contact your dealer for advice.
POSITIONING
Choose the installation location carefully. Avoid placing it in direct sunlight or close to a source of heat. No naked flame sources, such as lighted candles, should be placed on the unit. Also avoid locations subject to vibration and excessive dust, cold, or moisture. The unit can be used in a moderate climate.
This unit must be installed on a sturdy, level surface. Do not place it in a sealed area such as a bookcase or in a cabinet. Do not place the unit on an unstable surface or shelf. The unit may fall, causing serious injury to a child or adult as well as serious damage to the product. Do not place other equipment on top of the unit.
Due to stray magnetic fields, turntables or CRT TVs should not be located nearby due to possible interference.
Electronic audio components have a running-in period of around a week (if used several hours per day). This will allow the new components to settle down and the sonic properties will improve over this time.

POWER SOURCES
The unit should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power-supply to your home, consult your product dealer or local power company. If you do not intend to use this unit for a long period of time, unplug it from the mains socket.
OVERLOADING
Do not overload wall outlets or extension cords as this can result in a risk of fire or electric shock. Overloaded AC outlets, extension cords, frayed power cords, damaged or cracked wire insulation and broken plugs are dangerous. They may result in a shock or fire hazard.
Be sure to insert each power cord securely. To prevent hum and noise, do not bundle the interconnect leads with the power cord or speaker leads.
CLEANING
To clean the unit, wipe its case with a dry, lint-free cloth. Do not use any cleaning fluids containing alcohol, ammonia or abrasives. Do not spray an aerosol at or near the unit.
BATTERY DISPOSAL
Batteries may contain substances harmful to the environment. Please dispose of any discharged batteries with due consideration and in accordance with local nvironmental electronic recycling guidelines.
SERVICING
These units are not user serviceable. Never attempt to repair, disassemble or reconstruct the unit if there seems to be a problem. A serious electric shock could result if this precautionary measure is ignored. In the event of a problem or failure, please contact your dealer.

Plug Fitting Instructions (UK Only)
The cord supplied with this appliance is factory fitted with a UK mains plug fitted with a 3 amp fuse inside. If it is necessary to change the fuse, it is important that a 3 amp one is used. If the plug needs to be changed because it is not suitable for your socket or becomes damaged, it should be cut off and an appropriate plug fitted following the wiring instructions below. The plug must then be disposed of safely, as insertion into the main socket is likely to cause an electrical hazard. Should it be necessary to fit a 3-pin BS mains plug to the power cord the wires should be fitted as shown in this diagram? The colors of the wires in the main lead of this appliance may not correspond with the colored markings identifying the terminals in your plug. Connect them as follows:

The wire which is colored BLUE must be connected to the terminal which is marked with the letter ‘N’ or colored BLACK.
The wire which is colored BROWN must be connected to the terminal which is marked with the letter ‘L’ or colored RED.
The wire which is colored GREEN/YELLOW must be connected to the terminal which is marked with the letter ‘E’ or colored GREEN.
If a 13 amp (BS 1363) plug is used, a 5 amp fuse must be fitted, or if any other type of plug is used a 5 amp fuse must be fitted, either in the plug or adaptor or on the distribution board.

Rear panel connections

CAMBRIDGE AUDIO AXA35 Integrated Amplifier - Rear panel
connections

AUDIO INPUTS(A1-A4)
These inputs are suitable for any ‘line level’ source equipment such as the audio
outputs of CD players, streaming devices such as a Chromecast Audio (RCA Phono
to jack cable required) etc.
PHONO INPUT
This unit also has a built-in Phono stage.
Record players fitted with Phono Cartridges of the Moving Magnet (MM) or high output Moving Coil (MC) type (between 2-6mV output and 30-50k load impedance) can be used.
Low output Moving Coil types (<1mV and usually 10-1000 ohm load impedance) cannot be directly connected and will require a matching transformer or head amp.
Please consult your dealer for details.
Note: The ‘Ground’ terminals on both the record player and the AXA35 should be connected (where possible) with a ground wire for the lowest noise/hum pickup.
REC OUT
Connect to the recording input of a CD recorder input, tape deck, or another compatible recording device, etc.
This output provides a constant high-level output that does not fluctuate with the volume of the main unit. For this reason, the AXA35 cannot be used as a Preamplifier
only or with a subwoofer.
USB POWER 5V 500mA
This USB connection is designed to power a device such as a Streaming device or Bluetooth adaptor.
Note: This is not an input so will not allow you to play audio directly to the unit.
LOUDSPEAKER TERMINALS
Connect the wires from your left channel loudspeaker to the Left positive and negative terminals and the wires from the right channel loudspeaker to the Right positive and negative terminals.
In each case, the red terminal is the positive output and the black terminal is the negative output.
Care should be taken to ensure no stray strands of wire are accidentally connecting speaker outputs together as this may cause damage to the unit.
Please ensure that the loudspeaker terminals have been tightened adequately to provide a good electrical connection. It is possible for the sound quality to be affected if the screw terminals are loose.
VOLTAGE SELECT SWITCH
For servicing use only.
AC POWER SOCKET
Once all connections are complete, plug the AC power cable into an appropriate mains socket and turn the unit on.
Please only use the power lead supplied with the unit.

Front panel controls

POWER BUTTON
Switches the unit between Standby mode (indicated by the dim LED) and On (indicated by the bright LED). Standby mode is a low-power mode where the power consumption is less than 0.5 Watts. This product has APD (Auto Power Down) enabled as default. After an inactivity of 20 minutes, the product will automatically switch to Standby.
Auto Power Down (APD)
You can enable and disable the unit APD settings. This can be adjusted by pressing and holding the Power button until the LED flashes in sequence.
The two options below show which option is selected.
Standby flashes 5 times – APD disabled
Standby flashes 10 times – APD enabled
Note: Make sure the unit is On, before making changes to the APD function.
HEADPHONES SOCKET
This connection allows for the connection of stereo headphones with a 1/4-inch jack plug. Headphones with an impedance of between 32 and 600 ohms are recommended.
Note: Connecting headphones will automatically mute the loudspeaker outputs.
INFRARED SENSOR
Receives IR commands from the supplied remote control.
An unobstructed line of sight between the remote control and the sensor is required.
AUX IN
This source input allows you to connect a portable audio device such as an MP3 player or streaming device directly into the front of the unit using a 3.5mm stereo Aux lead.
Once plugged in, this input is automatically selected, although other inputs apart from A1 can still be selected once a stereo jack is plugged in. The A1/AUX button on
the front of the unit will select this input whilst a stereo jack is plugged in.
Note:
– Plugging a source into the front panel Aux input overrides the A1 input. Simply remove the jack from the front panel to automatically re-enable the A1 input.
– Also note that as the output level of Aux players tends to be quite low, the AXA35 adds 10dB to the current volume setting when (and only when) the Aux input is
selected.
INPUT SOURCE BUTTONS
(A1/AUX,A2, A3, A4,PHONO)
Press the relevant source button to select the desired input source.
DISPLAY
Used to display information such as the selected input source, volume and tone/ balance levels.
Note: When first purchased, the display will have a protective film over the top. Peel this off for a clear display.
MENU BUTTON
Pressing this once will select the Bass option. Pressing a second time will select the Treble option and pressing a third time will select the Balance option. When one of these options is selected, the volume control will adjust the level. If nothing is pressed for a while, the source will be displayed and the volume control will go back to controlling the volume level.
VOLUME CONTROL
Use to increase or decrease the level of the sound from the outputs of the unit. This controls the volume level of the loudspeakers and headphones. The volume control
will also change the level of bass, treble, and balance in the menu options.
Note: It does not affect the level of the ‘Rec Out’ output as this has a fixed level.

Remote Control

The AXA35 is supplied with a remote control that operates this unit and its built-in tuner. In addition, some icon buttons can operate a matching AXC35 or AXC25 player.
Always use Alkaline batteries.
POWER BUTTON
Switches the AXA35 between On and low power eco-friendly Standby mode.
MUTE
Mutes audio on the unit. Press again to cancel mute.
VOLUME
Increases or decreases the volume of the unit. Also used to change the bass, treble and balance settings when these are selected.
MENU
Toggles between Bass, Treble, and Balance options. Use the volume buttons to change the level of the selected option.
SOURCE BUTTONS
(A1/AUX,A2, A3, A4,PHONO)
Press the relevant button to select the desired music source.

Connections

LOUDSPEAKERS
Check the impedance of your speakers. You can use types with an impedance of 8 Ohms.
The red-colored speaker terminals are positive (+) and the black speaker terminals are negative (-). Make sure correct polarity is maintained at each speaker connector or the sound can become weak and “phase” with little bass.

CAMBRIDGE AUDIO AXA35 Integrated Amplifier -
LOUDSPEAKERS USING BARE WIRE CONNECTIONS
Prepare the speaker cords for connection by stripping off approximately 10mm (3/8”) or less of the outer insulation. More than 10mm could cause a short circuit. Twist the wires tightly together so there are no loose ends. Unscrew the speaker terminal, insert the speaker cable, tighten the terminal, and secure the cable.
Note: All connections are made using standard loudspeaker cables.

BASIC CONNECTION
The diagram below shows the basic connection of your amplifier to a CD player, turntable, and a pair of loudspeakers. CAMBRIDGE AUDIO AXA35 Integrated
Amplifier - BASIC CONNECTION

USING BANANA PLUGS
We recommend using Banana plugs with our units to establish a secure connection and ensure there are no loose strands of wire that may cause unwanted noise or interference.
Once you have stripped the outer insulation of the cable and twisted the wires as indicated above, securely connect these to your banana plugs, remove the dust cap from the end of the speaker terminal and push the plugin as far as possible without applying excessive force. CAMBRIDGE AUDIO AXA35 Integrated
Amplifier - USING BANANA PLUGS

Operating Instructions

After making any connections to your unit, activate the AXA35 by pressing the Power button on the front of the unit.
SETTING THE SOURCE
Press the Source button on the front of the unit corresponding to your desired source. Alternatively, you may use the appropriate button on the remote control

ADJUSTING THE VOLUME
Use either the Volume Up/Down buttons on the remote control, or the Volume control on the front of your unit system to change the volume level. The newly selected level will be indicated briefly on the front display.
The volume is displayed in minus dB where 0dB is the highest level.
A progressively larger negative number indicates the volume is being reduced.
CAMBRIDGE AUDIO AXA35 Integrated Amplifier - ADJUSTING THE
VOLUME ADJUSTING THE AUDIO SETTINGS
Adjustments to the bass, treble, and balance can be made as follows:

To enter the audio menu. Press either the Menu button on the front of the unit or on the remote control.
Step through the available settings by pressing the Menu button. The settings available are in order Bass, Treble, and Balance.
When you wish to make an adjustment for bass, treble, or balance, simply rotate the Volume control or use the Volume control buttons on the remote control.
To exit, wait for five seconds until the unit returns to normal mode.

Technical Specifications

Power output	35 watts (into 8Ω)
THD (unweighted)	<0.01% @ 1kHz, 80% of rated power

Troubleshooting

THERE IS NO POWER

Ensure the AC power cord is connected securely.
Ensure the plug is fully inserted into the wall socket and is switched on.
Check the fuse in the mains plug or adaptor.
Check the power is on at the front of the unit.

THERE IS NO SOUND

Check the correct input is selected.
Check that the speakers are connected correctly.
Check the unit is not in mute mode.
THE SOUND IS DISTORTED
Check speaker connections.

THERE IS A HUM COMING FROM THE SPEAKER

Ensure that all cable connections are secure, particularly ground/shield
connections for turntables.

THERE IS UNWANTED BACKGROUND NOISE AND INTERFERENCE

Move the unit away from other electrical equipment that is likely to cause
interference.
Ensure that all cable connections are secure, particularly ground/shield
connections for turntables.

THE REMOTE HANDSET WILL NOT FUNCTION

Check that the batteries are the correct way around and have not expired
Ensure that nothing is blocking the remote sensor.
If you experience any trouble with your product, visit the help section on our webpage at https://techsupport.cambridgeaudio.com
For all servicing, in or out of warranty, please contact your dealer

WWW.CAMBRIDGEAUDIO.COM
Gallery Court, Hankey Place
London
se1 4bb
United Kingdom
Cambridge Audio is a brand of Audio Partnership
Plc. Registered in England No. 2953313
AP36592/1

Documents / Resources

| CAMBRIDGE AUDIO AXA35 Integrated Amplifier [pdf] Instruction Manual
AXA35, Integrated Amplifier, AXA35 Integrated Amplifier
---|---
| Cambridge Audio AXA35 Integrated Amplifier [pdf] User Manual
AXA35 Integrated Amplifier, AXA35, Integrated Amplifier, Amplifier