PROGRESS LIGHTING P660005-XXX-30 LED Hood Step Light User Guide

June 3, 2024
PROGRESS LIGHTING

PROGRESS LIGHTING P660005-XXX-30 LED Hood Step Light

PROGRESS-LIGHTING-P660005-XXX-30-LED-Hood-Step-Light-Product-
Image

PACKAGE CONTENTS

HARDWARE CONTENTS (not actual size)

PROGRESS-LIGHTING-P660005-XXX-30-LED-Hood-Step-Light-
Fig-03

THANK YOU for selecting Progress Lighting

We can assist you with questions regarding product information, assembly or missing parts

800-447-0573
8am-8pm (Eastern), Monday-Friday
customerservice@progresslighting.com

Safety Information

Please read and understand this entire manual before attempting to assemble, operate or install the product.

CAUTION: Read instructions carefully and turn electricity off at main circuit breaker panel before beginning installation. CAUTION: Risk of fire. Min. 90°C supply conductors. Consult a qualified electrician to ensure correct branch circuit conductor. WARNING: If any Special Control Devices are used with this fixture, follow instructions carefully to assure full compliance with N.E.C. requirements. If there are any questions, contact a qualified electrical contractor.

CAUTION: All glass is fragile. Use care when handling glass shades and bulbs.
WARNING – To comply with the National Electrical Code and Underwriters Laboratories requirements, when installed outdoors, or in wet locations, the edge of the wall plate coming in contact with the mounting surface, must be sealed with a latex waterproof caulking to prevent water from entering the outlet box.

THIS PRODUCT MUST BE INSTALLED BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED, IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE.
KEEP THESE INSTALLATION INSTRUCTIONS

Preparation

  1. Before beginning installation, make sure all parts are included using the contents diagrams from page 1. If any part is missing or damaged, do not attempt to assemble, install or operate the product.
  2. Estimated assembly time: 30 minutes.
  3. Tools required for assembly (not included): Phillips screwdriver, pliers, wire stripper, safety glasses, electrical tape, ladder.

Care and Maintenance

Shut off main power supply before cleaning product or changing light bulbs. To clean, wipe with damp cloth. Do not use abrasive cleaners or cleaners that contain alcohol.

Assembly Instructions

PROGRESS-LIGHTING-P660005-XXX-30-LED-Hood-Step-Light-
Fig-04

  1. Strip 3/8″ of insulation from the electrical wire ends. Using wire nuts (BB), connect WHITE fixture wire to the WHITE supply wire from the outlet box; connect the BLACK fixture wire to the BLACK supply wire.
    Connect the fixture GROUND wire and supply GROUND wire using a wire nut or by fastening to the GROUND screw on the mounting plate. Push all wire connections into the outlet box.PROGRESS-LIGHTING-P660005-XXX-30-LED-Hood-Step-Light-
Fig-06

  2. Push all wires inside junction box then attach LED Assembly (8) on to the junction box, using the mounting screws supplied with the junction box (not included).

  3. Apply the gasket (D) to the desired cover (A or 8). Use the cover screws (BB) to tighten the front cover (A or B) and the gasket (D) down to the LED Assembly (C).

BB Cover screw

D Gasket

HORIZONTAL INSTALLATION SHOWN

PROGRESS-LIGHTING-P660005-XXX-30-LED-Hood-Step-Light-
Fig-09

PROGRESS-LIGHTING-P660005-XXX-30-LED-Hood-Step-Light-
Fig-10

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
  • Consult the dealer or an experienced radio/lV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

PROGRESS LIGHTING User Manuals

Related Manuals