ToolPRO PLU 583633 Radiator Pressure Test Kit Instruction Manual

ToolPRO PLU 583633 Radiator Pressure Test Kit

Important Safety Information

1. TO PREVENT STEAM BURNS, DO NOT OPEN CAP OF HOT OR WARM RADIATOR.
2. Pressurize only with hand pump. Do not use engine to pressurize system.
3. Loosen the radiator cap slowly.
4. Keep away from hot engine parts and fluids.
5. Use this product only according to these instructions. Improper use can create hazards.
6. Wear safety goggles and heat resistant work gloves during product assembly and use.
7. Refer to the vehicle’s service manual for specific radiator pressure testing instructions before use.
8. Clean up coolant spills immediately. Dispose of fluids according to local, state, and federal codes and regulations.
9. Keep work area clean and well lit.
10. Do not overreach. Keep proper footing and balance at all times.This enables better control of the product in unexpected situations.
11. Keep bystanders out of the area during assembly and use.
12. Do not assemble or operate when tired or when under the influence of drugs or medication.
13. This product is not a toy. Do not allow children to play with or near this product.
14. Use as intended only.
15. Inspect before every use. Do not use if parts missing or damaged.

Operating Instructions

1. Refer to the vehicle’s service manual for specific radiator pressure testing instructions.
2. Loosen the vehicle’s radiator cap slowly to relieve any excess pressure before removing the cap completely. Do not open the cap of a hot radiator.
3. Select the Proper Adapter and configuration of the Stationary Seat accessories. Securely attach the adapter to the filler neck of the radiator or expansion tank.
4. Attach the Quick Connector of the Hand Pump onto the Adapter.
5. Rapidly pump the Hand Pump while watching the pressure gauge. Pressurize the radiator up to the optimal pressure only – Do not over pressurize the radiator. Readings normally range 12 ~15 PSI. If the pressure level is too low, there may be a leak in the radiator or hose.
6. Once the test is complete, release the air pressure by pressing the Pressure Release Valve on the Hand Pump. Then disconnect the Quick Coupler and Adapter assembly.
7. Store the Kit in its Case in a clean, dry, safe location out of reach of children.

Parts List and Diagram

Part

|

Description

|

**Function***

---|---|---

1

| Pump|

2

| Blue Adapter| Skoda®, SAAB®, Ford®, Daewoo®, Audi® A4, A5, A6

3

| Yellow Adapter| Skoda, Seat®, Audi, Opel®, VW®, Ford

4

| Purple Adapter| Seat, Alfa Romeo®, Audi, BMW®

5

| Orange Adapter| Land Rover®, BMW

7

| Adapter| Lancia®, Volvo®, Land Rover®, Renault®,

Peugeot®, Opel®, Honda®, Fiat®, Citroen®, Audi, VW®

8

| Adjustable Seat| Toyota®, Suzuki®, Nissan®,

Mitsubishi®, Mercedes®, Chrysler®, Citroen

9

| 50mm Seat| Use with item 8

for Japanese and European cars

10

| 35mm Seat| Use with item 8 for Japanese and European cars including: Suzuki, Nissan, Mitsubishi, Chrysler, Citroen, Mercedes

11

| 27mm Seat| Use with item 8 for Japanese and European cars including: Toyota, Suzuki, Nissan

13

| Adapter| Kia®

14

| Clip| Use with adapters and seat

accessories for: Toyota, Suzuki, Mitsubishi, Nissan

15

| Adapter| Honda, Toyota

16

| Adapter| Opel, Hyundai®, Honda,

Mitsubishi, Ford, Nissan, Mazda®, Toyota

21

| Green Adapter| GM®

22

| Adapter| GM, Ford

19

| Case|

NOTE: Kit may work for only some models under each indicated make.

NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>