ANKER PowerHouse 90 User Manual

ANKER PowerHouse 90

At a Glance

INSTRUCTION

1. Flashlight Button
2. AC LED Indicator
3. Power Button
4. Flashlight
5. USB-C Port
6. USB-A Port
7. AC Outlet

Charging Your USB Devices

Charging Your Smart Watches or Bluetooth Earphones

• X2: Press twice
• X1: Press once

1. To activate the trickle-charging mode, press the power button twice.
   The LED indicator will turn green.

2. Charge your smartwatch, Bluetooth earphones, or other lowpower accessories.

3. To turn off trickle-charging mode, press the power button once again.

Charging Your Devices via the AC Port

Press and hold the Power Button to enable or disable AC function.
When the AC function is enabled, the AC LED indicator will turn blue.

1. PowerHouse 90 is not recommended for charging your CPAP.

2. When the power button is turned on, even if no devices are being charged, there will still be a certain amount ofno-load power consumption. Therefore, it’s best to turn offthe power button after use to avoid draining power.

3. The maximum power output of the AC port is 100W.
   If you use the AC port to charge devices greater than100W, the PowerHouse will automatically turn off.

4. When the AC LED indicator blinks red, it indicates that your PowerHouse is not working properly. DO NOT use PowerHouse until all faults are fixed.

Recharging Your PowerHouse

Recharge your PowerHouse via the USB-C port at a maximum input of 45W.

Flashlight Mode

• Press the Flashlight Button once to turn on the flashlight.
• Press once to toggle between low brightness, full brightness, and the SOS mode.

×1: Press once

For FAQs and more information, please visit:

anker.com/support

• @Anker
• @Anker Japan
• @Anker Deutschland
• @AnkerOfficial
• @Anker_JP
• @anker_official
• @anker_jp

Product Number:
PowerHouse 90
51005003518 V01

Specifications

IMPORTANT SAFETY INSTRUCTIONS

WARNING – When using this product, basic precautions should always be followed, including the following:
Read all the instructions before using the product.

• To reduce the risk of injury, close supervision is necessary when the product is used near children.

• Do not put fingers or hands into the product.

• Do not expose PowerHouse to rain or snow.

• Use of a power supply or charger not recommended or sold by the powerhouse manufacturer may result in a risk of fire or injury to persons.

• Do not use PowerHouse in excess of its output rating. Overload outputs above rating may result in a risk of fire or injury to persons.

• Do not use a PowerHouse that is damaged or modified.
  Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.

• Do not disassemble the powerhouse. Take it to a qualified service person when service or repair is required. Incorrect reassembly may result in a risk of fire or injury to persons.

• Do not expose the powerhouse to fire or excessive temperature.
  Exposure to fire or temperature above 100°C may cause an explosion.

• Have servicing performed by a qualified repair person using only identical replacement parts. This will ensure that the safety of the product is maintained.

• Switch off the power bank when not in use.

1. Store the product in a cool, dry place
2. Do not store the product in hot or humid environment
3. Use of a power supply or charger not recommended or sold by the product manufacturer may result in a risk of fire or injury to persons.
4. Operating temperature should be between 0°C to 40°C.
5. Do not disassemble the product. Take it to a qualified service person when service or repair is required. Incorrect reassembly may result in a risk of fire or injury to persons.
6. If the product is not used for long periods of time, you should change and discharge once every three months.
7. When charging a device, the product may feel warm, this is a normal operating condition and should not be cause for concern.
8. In normal conditions, the battery performance will decline over several years.
9. Do not dispose of the product in heat or fire.
10. Do not clean the product with harmful chemicals or detergents.
11. Misuse, dropping or excessive force may cause product damage.
12. When disposing of secondary cells or batteries, keep cells or batteries of different electrochemical systems separate from each other.
13. Be aware discharged battery may cause fire or smoke, tape the terminals to insulate them

Notice

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The following importer is the responsible party.
Company Name: Fantasia Trading LLC
Address: 5350 Ontario Mills Pkwy, Suite 100, Ontario, CA 91764
Telephone: +1-800-988-7973

IC Statement
This device complies with Industry Canada license-ICES-003.
Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.

Declaration of Conformity
Hereby, Anker Innovations Limited declares that the product type A1710 is in compliance with Directive 2014/30 /EU. The full text of the EU declaration of conformity is available at the following internet address:
http://www.anker.com
Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok,
Kowloon, Hong Kong
Anker Innovations Deutschland GmbH Georg-Muche-Strasse 3-5, 80807 Munich, Germany

Customer Service

18-Month Limited Warranty
support@anker.com
(US) +1 (800)988 7973 Mon-Fri 6:15AM – 5:00PM(PT)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>