resideo R7284 Series Electronic Oil Primary User Guide

June 7, 2024
resideo

resideo R7284 Series Electronic Oil Primary User Guide
resideo R7284 Series Electronic Oil Primary

The following service procedures will help you become familiar with the R7284 electronic oil primary controls. For control operation, please refer to the basic control functions described on the back. For further information, wiring instructions and troubleshooting, please refer to the R7284 Installation Instructions, form number 69-2467.

Pump Priming Cycle

To facilitate purging air from the oil lines and filters, the R7284 can be placed in a purge routine by pressing and releasing the up arrow button during the Trial For Ignition.

In the advanced interface “PUMP PRIME” is displayed on the display along with the time left on the Trial for Ignition (TFI). Pressing the up arrow button adds a minute to the TFI time for a maximum of 10 additional minutes (press the up arrow button 10 times). Pressing the down arrow button subtracts a minute from the TFI time.

There is no visual indication for the basic interface control and the purge timing is limited to five minutes.

Home Screens (Advanced Interface)

Pressing the “i” button longer than 2 seconds in states other than Standby Interrupts control operation.

Once the held key is released a 3 second count down begins to restart the cycle if the call for heat is still present.

  • Holding all 3 buttons longer than 2 seconds in any state puts the display in the Installer Setup (ISU) mode.
  • Pressing “i” in any state enters the Diagnostic screen ifdiagnostics are enabled  outside of the Installer Setup mode.
  • Pressing up or down in any screen enters Error History if diagnostics are enabled outside of the Installer Setup mode.

Below is a typical progression of screens through a normal cycle.
Pressing up or down during the Ignition Trial enters pump prime.
Each press of the up button adds a minute, each press of the down button subtracts a minute from the pump prime time.

If at any point there is an event generating a lockout, one of the following screens will be displayed.

Control is in Soft Lockout. Control will recover when error clears or after specified time.
Control is in Hard Lockout. Hold “i” for at least 2 seconds to reset.
Hold the “i” button longer than 10 seconds to return to Standby

Installer Setup (Advanced Interface)

Installer setup is entered by pushing all three buttons simultaneously for 2 seconds.

If QUIT is selected, an “i” button press displays the Re-baseline option.
If CONT is selected, an “i” button press goes to “Installer Setup”.

NOTE: Not all parameters are adjustable in all models. Parameters not available for adjustment will display “Locked” when an attempt is made to modify them.

Select between English, French, or Spanish by using the up or down buttons and the “i” button to select.
Adjustment of the Valve On Delay in five second increments.
Ignition (lockout) Time adjustment.

NOTE: The Ignition Time is only available for adjustment during the first 100 cycles of operation. After 100 cycles the Ignition Time is locked in and can no longer be adjusted.

Adjustment of the Burner Off Delay. Burner Off Delay can be adjusted in 15 second increments from 0 to 8 minutes.
Configuration of the TT terminals vs. an “internal jumper.” This option allows you to jumper the TT terminals electronically so no physical jumper is needed.
Controls sparking during On Delay period.Controls sparking during Run mode (Interrupted vs. Intermittent ignition).
Number of resets allowed before Restricted Lockout.
Appliance configuration (boiler, furnace, water heater) for EnviraCOM™.
Enable advanced diagnostics mode and errorhistory. Selecting NO allows access to error history and diagnostics only by entering Installer Setup.
Exit installer setup.
If “QUIT” is selected, the user is prompted with a screen asking if it is desired to rebaseline the control.

Installer Setup

Error History Screens (Advanced Interface)

  • For all Error History screens, pressing “i” returns to the Normal Screen.

  • From the home screen, press the up button to display most recent error.

  • Press the up button again to proceed to the next most recent error or the down button to return to the previous error screen.

  • These three screens transition every 3 sec.

  • If no more errors are logged, the display shows “Error History End.”

Basic User Interface

The basic user interface consists of 3 buttons and an LED. Simple diagnostic information can be obtained through the interaction of the buttons and LED.

R7284 Status (Basic Interface)

Table 1. LED Codes.

Description

| LED Code
---|---
Standby|

Pulse (1/4 sec. ON, 4 sec OFF)

Call for Heat

| Heartbeat (1/2 sec bright, 1/2 sec dim) *
Flame proven|

On solid

Recycle

| 2 second ON, 2 second OFF flashing
Lockout|

1/2 second on, 1/2 second OFF flashing

Interrupt

| OFF
“i” button|

Flame Strength Indication

Up button

| Most recent error
Down button|

Next most recent error

R7284 Flame Strength (Basic Interface)

During normal operation and when the R7284 is in the Running state, the LED will show CAD cell resistance. See Table 2.

Table 2. Flame Strength Indication

Flame Strength Indication

| Number of 1/2 sec flashes
---|---
Cad Cell less than 400L|

1

400L < Cad Cell < 800L

| 2
800L < Cad Cell < 1600L|

3

1600L < Cad Cell < 6100L

| 4
Cad Cell > 6100L|

None

Error History (Basic Interface)

The last two errors are available for display on the LED:

  • Pressing the up arrow button displays the most recent error.
  • Pressing the down arrow button displays the next most recent error.

Once the up or down arrow is pushed, the LED will display the most recent or next most recent alarm by blinking the error code. See Table 3.

R7284 Error Codes (Basic Interface)

Table 3. Error Codes.

Error Codes

| Number of 1/4 sec flashes
---|---
No ignition / Late ignition|

1

Max flame losses / Cad Cell high while running

| 2
Flame out of sequence|

3

Low Voltage / EnviraCOM™ error

| 4
Internal Error|

5

Contact Us

Resideo Technologies, Inc.
1985 Douglas Drive North, Golden Valley, MN 55422
1-800-468-1502
69-2500—02 M.S. Rev. 03-21 | Printed in United States
http://www.resideo.com/

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals