KitchenAid JFFCC72EFS04 PrintShield Finish Counter Depth French Door Refrigerator Instruction Manual

June 9, 2024
KitchenAid

KitchenAid logo JFFCC72EFS04 PrintShield Finish Counter
Depth French Door Refrigerator

Instruction Manual

JFFCC72EFS04 PrintShield Finish Counter Depth French Door Refrigerator

IMPORTANT:

  • Pressure regulator kit intended for use on the above models to assist in the dispensing of water in households with high water pressure.
  • Connect the pressure regulator to your water supply line in accordance with all state and local codes and ordinances.
  • Make sure to turn off water supply before installation.
    KitchenAid JFFCC72EFS04 PrintShield Finish Counter Depth French Door
Refrigerator - Figure 1

Kit Contains:
A. (1) Pressure Regulator
B. (1) Mounting Clip
C. (1) Screw
D. (2) Adhesive-backed Tubing Clip
E. (1) Installation Instruction (not pictured)
F. (1) Waterline-valve-regulator (not pictured)
NOTE: Attaching the pressure regulator will require a 2” spacing from back of appliance to the wall. This may be greater than before installation, causing the appliance to stick out further.
Tools Needed:

  • PEX Tube Cutter –OR– Utility Knife
  • Phillips Screwdriver
  • Small container for draining the hose
  • Copper Tubing Cutter (If copper water line)

WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.

PREPARING THE APPLIANCE FOR SERVICE

  1. Unplug appliance or disconnect power.
  2. Turn the water off at the household supply.
  3. If servicing a refrigerator, purge the product by dispensing water for at least 30 seconds.
  4. Locate the line connecting the household supply to the product. Disconnect the supply line from the household side, using the container to catch the draining water. Do not disconnect from the product.

INSTALLING THE PRESSURE REGULATOR

  1. Use the provided 24″ (61cm) long PEX water line.

  2. Using the tube cutter or utility knife, cut the household supply line at the measurement. Ensure that tubing is cut square with no burrs, sharp edges, or deformation to prevent leaking.

  3. For bottom mount and side-by-side platforms, locate and remove one of the center screws holding the machine compartment cover in place. (If not available, locate a similar location on the product.) See Figure 2.
    KitchenAid JFFCC72EFS04 PrintShield Finish Counter Depth French Door
Refrigerator - Figure 2

  4. Using the existing hole, attach the mounting clip with the provided screw. Tighten screw so that the clip does not freely rotate. See Figure 3.
    KitchenAid JFFCC72EFS04 PrintShield Finish Counter Depth French Door
Refrigerator - Figure 3

  5. Connect the pressure regulator in between the loose ends of the water line by pressing the line ends firmly into the pressure regulator’s connectors. See Figure 4.
    IMPORTANT: Ensure that the water flow direction indicator arrow on the pressure regulator is pointing in the direction of the water flow (towards the appliance).  Verify that the connection is properly made by gently attempting to pull the line straight out. If the line remains connected, the connection was properly made.
    KitchenAid JFFCC72EFS04 PrintShield Finish Counter Depth French Door
Refrigerator - Figure 4

  6. Attach the pressure regulator to the mounting clip in the orientation shown (Vertical: Outlet on bottom / Inlet on top) See Figure 5.
    KitchenAid JFFCC72EFS04 PrintShield Finish Counter Depth French Door
Refrigerator - Figure 5

  7. If necessary, add the two adhesive-backed tubing clips on the household supply line to support the line and prevent kinking. See Figure 6.
    KitchenAid JFFCC72EFS04 PrintShield Finish Counter Depth French Door
Refrigerator - Figure 6

RECONNECTING THE APPLIANCE

  1. Reconnect the water supply connections as specified by the product installation instructions, supplied with the product.

  2. Turn on the household water supply.
    WARNING
    Electrical Shock Hazard
    Plug into a grounded 3 prong outlet.
    Do not remove ground prong.
    Do not use an adapter.
    Do not use an extension cord.
    Failure to follow these instructions can result in death, fire, or electrical shock.

  3. Reconnect power to the product.

  4. Ensure the product is turned on and cooling.

  5. If servicing a refrigerator, purge the product by running the water for at least one minute.

NOTE: If there is no water, check that the pressure regulator was installed in the proper flow direction.
IMPORTANT: Check all connections for leaks. When placing the product into its final location for usage be sure not to kink the household supply line. A kinked supply line  could cause no ice or water, or low ice and water problems. Leave a two inch (2”) minimum gap between the appliance back and wall.

W11502228A
®/™ ©2020 All rights reserved.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

KitchenAid User Manuals

Related Manuals