70mai Dash Cam A800 User Manual
- June 7, 2024
- 70mai
Table of Contents
70mai Dash Cam A800
User Manual
Product Overview
Please read this manual carefully before using the product and keep it in a safe place.
1.Function Buttons
2.Display
3.Speaker
4.Mounting Slot
5.Camera
6.Ventilation Holes| 7.Indicator
8.Microphone
9.Power Button
10.Power Port
11.Rear Camera Port
12.Memory Card Slot
---|---
Note: Illustrations of the product, accessories, and user interface in the user manual are for reference purposes only. The actual product and functions may vary due to product enhancements.
Installation
-
Installing the electrostatic sticker.
Clean your windshield and put the electrostatic sticker on the recommended area as shown in the figure below. Avoid the edge of the windshield and select the flat and smooth area for the installation. Make sure you remove air bubbles between the sticker and the glass.
-
Installing the memory card.
Insert the memory card into the card slot with its contacts facing up until you hear a click. The memory card is well-installed.
-
Installing the mount.
Attach the mount into the slot and slide up, as shown in the figure below. You will hear a snap when it is in place. Make sure the mount is securely installed on the dashcam.
-
Mounting the dashcam.
Peel off the protective film from the adhesive sticker on the base of the mount, and paste the dashcam onto the electrostatic sticker in the dotted area.
-
Connecting the power supply.
As shown in the figure below, run the power cord along the top of the windshield, down the A-pillar, and around the glove compartment, so that the power connector is near the cigarette lighter. Connect the power cord to the car charger, then plug the charger into the cigarette lighter socket.
Note:
●Use the included crowbar to hide the power cord underneath the vehicle’s headliner and rubber seal along the A-pillar.
●Depending on the vehicle, the cigarette lighter socket may be located in a different position. The above figure is for reference only. -
Adjusting the dashcam angle.
Turn on the dashcam and adjust the camera angle based on the preview screen to ensure that the camera is facing the front of the vehicle.
Accessories (optional)
The rear recording function of this product needs to be used with the rear cameras. Scan the QR code below to obtain the operation guide for rear camera.
https://help.70mai.asia/1060.html
Note: To avoid the rear camera malfunction due to device incompatibility, it is recommended to use a rear camera from the 70mai brand.
Packing list
1. 70mai Dash Cam A800×1
2. Mount ×1
3. Power Cord×1
4. Dual USB Car Charger×1| 5. Wiring Crowbar×1
6. Electrostatic Sticker × 2
7. Adhesive Sticker × 2 (with 1 pre-applied to the mount)
8. User Manual×1
---|---
Download 70mai App
This product may be used in conjunction with the 70mai App. Please search for
“70mai” in the App Store or scan the following QR code to download and install
the App.
https://www.70mai.com/en/download/?souce=QrcodeVue
Note: Android 4.4 & iOS 9.0 or above is required to connect to the dash cam’s Wi-Fi hotspot with a mobile phone.
Online Guide
Scan the below QR code to access the online guide. The guide provides detailed
product information including descriptions of functions. Please carefully read
this guide before use in order to avoid damage due to incorrect use.
https://help.70mai.asia/1029.html
Memory Card Instructions
A memory card (sold separately) must be installed in the dashcam before use.
The dashcam supports standard MicroSD cards. Please use memory cards with a
minimum capacity of 32 GB and a rating of U1(UHS-1 ) or above.
The default file partition format of the memory card may be inconsistent with
the format supported by the dashcam. When inserting the memory card for the
first time, please format it in the dash that came before use. Formatting the
memory card will delete all files on the card. Please back up important data
to another device beforehand. The memory card may become damaged or
deteriorated after repeated cycles of overwriting, and this may affect its
ability to save video and image files. If this occurs, immediately replace it
with a new memory card. Please use a high-quality memory card purchased from a
reputable vendor. Inferior memory cards may have issues such as actual
reading/writing speeds that do not match the stated speeds and an actual
storage capacity that does not match the stated storage capacity. We shall not
be held liable for lost or damaged videos caused by the use of a low-quality
memory card. In order to avoid reading and writing speeds decreasing after
prolonged use, it is recommended to format the memory card in the dashcam
every two weeks. Do not insert or remove a memory card while the dashcam is
turned on.
Precautions
Before using this dash cam, please read all the precautions and the online guide to ensure correct and safe use.
-
This dashcam is intended to assist drivers with the purpose of recording the environment outside the vehicle.
The dashcam does not guarantee the user’s driving safety. We shall not be held liable for any accident, damage, or loss of information caused by operating the dashcam while driving. -
Due to differences in vehicle conditions, driving style, driving environment, etc., some functions may not work properly. A power failure, usage in environments outside the normal operating temperature or humidity range, a collision, or a damaged memory card may cause the dashcam to function abnormally. There is no guarantee that this dash cam will function normally under all circumstances. Videos recorded by this dash cam are for reference only.
-
Please install this dashcam correctly, and do not block the driver’s line of sight, nor block the vehicle’s airbag, in order to avoid product failure or personal injury.
-
The maximum resolution of the single-camera of the dashcam is 3840×2160; after installation of the rear camera, the maximum resolution is 2560×1600. After removal of the rear camera, if you want to revert to resolution 3840×2160, please change in Settings > Video settings > Video resolution.
-
Please use the included car charger, power cord, and other accessories in order to avoid product failure due to non-conformance. We shall not be held liable for any loss or damage caused by the use of a non-genuine car charger or power cord.
-
If the battery becomes deformed, swollen, or starts leaking during use or storage, stop using the dashcam immediately in order to avoid safety issues, and contact after-sales service.
-
Please keep this dashcam away from any strong magnetic fields, as they may cause damage to the dashcam.
-
Do not use this dash cam in environments with temperatures over 60°C or below -10°C.
-
Please only use this dash cam within the scope permitted by law.
Specifications
| Product: Dash Cam | Model: A800 | Input: SV= 2A |
|---|---|---|
| Power Supply: Car cigarette lighter socket | Battery Type: Lithium polymer |
battery
FCC
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 cm between the radiator & your body. This transmitter
must not be co-located or operating in conjunction with any other antenna or
transmitter.
WEEE Information
All products bearing this symbol are waste electrical and electronic equipment
(WEEE as in directive 2012/19/EU) which should not be mixed with unsorted
household waste. Instead, you should protect human health and the environment
by handing over your waste equipment to a designated collection point for the
recycling of waste electrical and electronic equipment, appointed by the
government or local authorities. Correct disposal and recycling will help
prevent potential negative consequences to the environment and human health.
Please contact the installer or local authorities for more information about
the location as well as the terms and conditions of such collection points.
CE Information
The manufacturer hereby, declares that this equipment is in compliance with
the applicable Directives and European Norms, and amendments. The full text of
the EU declaration of conformity is available at the following internet
address: http://www.mi.com/global/service/support/declaration.html
Service: help@70mai.com
For further information, please go to www.70mai.com
Manufacturer: 70mai Co., Ltd.
Address: Room2220, building2, No.588,
Zixingroad, MinHangDistrict, Shanghai, China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>