ozito PXCG-060 Standard Charger Instruction Manual
- June 7, 2024
- ozito
Table of Contents
18V LITHIUM-ION
STANDARD CHARGER
INSTRUCTION MANUAL
PXCG-060
SPECIFICATIONS
| Input: | 220-240V ~AC 50-60Hz |
|---|---|
| Output: | 18V DC, 1.5A |
| Battery Charge Time: | 60Min – PXBP-150 (18V 1.5Ah) |
80Min – PXBP-200 (18V 2.0Ah)
120Min – PXBP-300 (18V 3.0Ah)
160Min – PXBP-400 (18V 4.0Ah)
215Min – PXBP-520 (18V 5.2Ah)
215Min – PXUBP-520 (18V 5.2Ah Ultra)
- Charging Unit LEDs
- Charging Unit
DESCRIPTION OF SYMBOLS
V
| Volts|
Hz
| Hertz
---|---|---|---
A
| Amperes|
Ah
| Amp Hour
| Read Instruction Manual|
| Double Insulated
| Indoor Use Only|
| Do not dispose of in rubbish
| Do not charge the battery in temperatures exceeding 40°C|
| Regulatory Compliance
Mark (RCM)
| 2.0A Slow Blow Fuse|
| Warning
CARING FOR THE ENVIRONMENT
Power tools that are no longer usable should not be disposed of with household
waste but in an environmentally friendly way. Please recycle where facilities
exist.
Check with your local council authority for recycling advice.
Recycling packaging reduces the need for landfills and raw materials. The reuse of recycled material decreases pollution in the environment. Please recycle packaging where facilities exist. Check with your local council authority for recycling advice.
ELECTRICAL SAFETY
WARNING! When using mains-powered tools, basic safety precautions,
including the following, should always be followed to reduce the risk of fire,
electric shock, personal injury, and material damage.
Read the whole manual carefully and make sure you know how to switch the tool
off in an emergency, before operating the tool.
Save these instructions and other documents supplied with this tool for future
reference.
Note: The supply of 230V and 240V on Ozito tools are interchangeable for
Australia and New Zealand.
This charger is double insulated therefore no earth wire is required
If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard.
Note: Double insulation does not take the place of normal safety precautions
when operating this tool.
The insulation system is for added protection against injury resulting from a
possible electrical insulation failure within the tool.
Using an Extension Lead
Always use an approved extension lead suitable for the power input of this
tool. Before use, inspect the extension lead for signs of damage, wear, and
aging. Replace the extension lead if damaged or defective.
When using an extension lead on a reel, always unwind the lead completely. Use
of an extension lead not suitable for the power input of the tool or which is
damaged or defective may result in a risk of fire and electric shock.
To reduce the risk of electric shock, we recommend the use of a residual
current device (rated 30mA or less).
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge unless they have been given supervision or instruction concerning
the use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the
appliance.
ONLINE MANUAL
Scan this QR Code with your mobile device to take you to the online manual.
[www.ozito.com.au/products/PXCG-060](http://www.ozito.com.au/products/PXCG-060)CHARGER SAFETY WARNINGS
THIS MANUAL CONTAINS IMPORTANT SAFETY AND OPERATING INSTRUCTIONS FOR YOUR CHARGER.
- Before using the charger read all instructions and cautionary markings on the charger, battery pack, and the product using the battery pack.
- This charger is not intended for any uses other than charging Ozito Power X Change rechargeable batteries. Any other use may result in a risk of fire, electric shock, or electrocution.
- Do not place any object on top of the charger or place the charger on a soft surface that may result in excessive internal heat. Place the charger in a position away from any heat source.
- To reduce the risk of damage to the electric plug and cord, pull by the plug rather than the cord when disconnecting the charger.
- Make sure the cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress.
- An extension cord should not be used unless absolutely necessary. Use of an improper extension cord could result in the risk of fire, electric shock or electrocution.
- Do not operate the charger if it has received a sharp blow, been dropped or otherwise damaged in any way. Has it been checked by an electrician or power tool repairer?
- Do not disassemble the charger. Take it to an electrician or power tool repairer when service or repair is required. Incorrect reassembly may result in a risk of electric shock, electrocution or fire.
- To reduce risk of electric shock, unplug the charger from the outlet before attempting any B cleaning. Removing the battery pack will not reduce this risk.
- Never attempt to connect 2 chargers together.
- The charger is designed to operate on standard household electrical power (240 volts). Do not attempt to use it on any other voltage!
- DO NOT USE the charger where the temperature may reach below 0° or exceed 40°C. If the battery pack is too hot or too cold charging will cease and begin automatically only when the battery reaches the correct charging temperature.
- Do not incinerate the battery pack even if it is seriously damaged or is completely worn out. The battery can explode in a fire.
- Never attempt to open the battery pack for any reason. If the plastic housing of the battery pack breaks or cracks, immediately discontinue use and do not recharge.
- During charging, the battery must be placed in a well-ventilated area.
CHARGING A BATTERY
CAUTION: THE CHARGER SHOULD BE PROTECTED BY A RESIDUAL CURRENT DEVICE (RATED AT 30MA OR LESS).
- Place the charger on a flat surface then connect the charger into a mains power outlet.
- The charger LED will flash green showing power is being supplied to the charger.
- Align and then slide the ribs on the battery into the recess in the charger.
- The red LED will illuminate while the battery charges.
- The green LED will illuminate once the battery is fully charged.
Charger LED Indicator Lights
LED Indicator| Situation
GREEN (Flashing)| Stand By (no battery pack is inserted)
RED (Flashing)| Battery is charging (low charge)
RED (Illuminated)| Battery is fast charging (mid charge)
GREEN (Illuminated)| Battery is fully charged and is ready for use. Refer to
charging times to ensure the battery is fully charged.
BOTH(Illuminated)| Battery pack is too hot or too cold (charging will begin
automatically when the battery reaches the correct charging temperature).
BOTH (Flashing)| The battery is defective, charging is no longer possible. Do
not charge. Contact Ozito Customer Service.
Mounting The Charging Unit On A Wall
The charging unit can be mounted to a wall or workbench.
The correct dimensions for drill holes can be found on the back of the
charging unit; a template for the mounting hole locations can also be found on
the Ozito website.
Note: When mounting on a wall you must use suitable screws, e.g.M3 pan-
head screws, in order to prevent damage to the housing and risk of falling.
MAINTENANCE
- Disconnect the charger from the power source before cleaning.
- Keep the charger in a dry place out of reach of children.
- If the enclosure of the charger requires cleaning, do not use solvents. Use a dry, soft cloth only to wipe down the surface. Never let any liquid get inside the charger; never immerse any part of the charger.
- There are no other parts inside the charger that require maintenance. Do not take the charger apart. If the charger is damaged, contact your supplier or the manufacturer.
WARRANTY
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST RETURN THE PRODUCT TO
YOUR NEAREST BUNNINGS WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE OUR CUSTOMER SERVICE
HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL NUMBER AND DATE OF PURCHASE
AVAILABLE. A CUSTOMER SERVICE REPRESENTATIVE WILL TAKE YOUR CALL AND ANSWER
ANY QUESTIONS YOU MAY HAVE RELATING TO THE WARRANTY POLICY OR PROCEDURE.
The benefits provided under this warranty are in addition to other rights and
remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded at law. You are
entitled to a replacement or refund for a major failure and for compensation
for any other reasonably foreseeable loss or damage. You are also entitled to
have the goods repaired or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a major failure.
Generally, you will be responsible for all costs associated with a claim under
this warranty, however, where you have suffered any additional direct loss as
a result of a defective product you may be able to claim such expenses by
contacting our customer service helpline above.
36 MONTH REPLACEMENT WARRANTY
Your product is guaranteed for a period of 36 months from the original date of
purchase and is intended for DIY (Do It Yourself) use only. If a product is
defective it will be replaced in accordance with the terms of this warranty.
Warranty excludes consumable parts.
WARNING
The following actions will result in the warranty being void.
- If the tool has been operated on a supply voltage other than that specified on the tool.
- If the tool shows signs of damage or defects caused by or resulting from abuse, accidents, or alterations.
- Failure to perform maintenance as set out within the instruction manual.
- If the tool is disassembled or tampered with in any way.
OZITO Australia/New Zealand (Head Office)
1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>