DoorBird A1061x Series IP Door Chime Installation Guide

DoorBird A1061x Series IP Door Chime

INSTALLATION MANUAL

Read these instructions carefully before starting to use any components. Keep the manual so you can refer to it at a later date if required. If you hand over the device to other persons for use, please hand over the operating manual as well.
To make things easier we use the term “device” for the product “DoorBird IP Door Chime” and “mobile device” for a smartphone or tablet. You can always find the most up-to-date version of the installation manual on www.doorbird.com/support

Liability
Every care has been taken in the preparation of this document.
Please inform Bird Home Automation GmbH of any inaccuracies or omissions. Bird Home Automation GmbH cannot be held responsible for any technical or typographical errors and reserves the right to make changes to the product and manuals without prior notice. Bird Home Automation GmbH makes no warranty of any kind with regard to the content of this document, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Bird Home Automation GmbH shall neither be liable nor responsible for incidental or consequential damages in connection with the furnishing, performance or use of this material. This product is only to be used for its intended purpose.

Equipment Modifications
This equipment must be installed and used in strict accordance with the instructions given in the user documentation. This equipment contains no components that require service by the user. Unauthorized equipment changes or modifications will invalidate all applicable regulatory certifications and approvals.

Hazard information

WARNING:

• Mounting, installation and servicing work on electrical devices may only be performed by a qualified eletrician. Failure to observe this regulation could result in the risk of serious damage to health or fatal injury due to electric shocks.
• Devices with 110-240 V connection: The device may only be connected to an easily accessible power socket outlet. The mains adapter must be pulled out if a hazard occurs.
• For power supply, only use the original plug-in mains adapter delivered with the device or a recommended PoE-Switch/PoE-Injector as specified in this manual.
• Because of electrostatic charging, direct contact with the circuit board can result in destruction of the device. Direct contact with the circuit board must therefore be avoided at any time.
• Observe the EN 60065 resp. EN 60950 resp. EN 62368 standard.
• Do not use the device if there are signs of damage to the housing, control elements or connecting sockets, for example, or if it demonstrates a malfunction. If you have any doubts, please have the device checked by an authorized expert.
• Do not open the device. This voids the warranty of the device. The device does not contain any parts that can be maintained by the user. In the event of an error, please have the device checked by an authorized expert.
• For safety, approval and licensing reasons (CE/FCC/IC etc.), unauthorized change and/or modification of the device is not permitted.
• The device is not a toy; do not allow children to play with it. Do not leave packaging material lying around. Plastic films/bags, pieces of polystyrene, etc. can be dangerous in the hands of a child.
• Always lay cables in such a way that they do not become a risk to people and domestic animals.
• Voltage is applied to parts within the equipment. Do not touch any parts that are not associated with the installation, wiring, or connection. Electric shock could result.
• On devices which are not marked as weather-proof: Keep the device away from water or any other liquid.
• Do not install or make any wire terminations while power supply is plugged in. It can cause eletric shock or damage to the device.
• Before turning on power, make sure wires are not crossed or shorted. If not, fire or eletric shock could result.
• High voltage may be present internally. Do not open the device. Electric shock could result.
• The device is not of explosion-proof. Do not install or use near gases or flammable materials. Fire or explosion could result.
• Do not install two power supplies in parallel to a single input. Fire or damage to the device could result. Be sure to connect a single power supply to the device.
• Do not connect any terminal on the device to an AC power line. Fire or electric shock could result.
• Keep AC cord from being marred or crushed. If the AC cord is fractured, fire or electric shock could result.
• Do not plug or unplug with wet hands. Electric shock could result.
• Do not put any metal or flammable material into the device. Fire, electric shock, or device trouble could result.
• Existing wiring may contain high voltage AC electricity. Damage to the device or electric shock could result. Wiring and installation must be done by a qualified eletrician.
• When mounting the device on a wall or ceiling, install the device in a convenient location, but not where it could be jarred or bumped. Injury could result.
• On devices with ground terminals, connect to an earth ground. Otherwise fire or malfunction could result.
• On devices with plastic or real glass, do not put high pressure on the glass. If fractured, injury could result.
• On devices with LCD, if LCD is punctured, do not allow contact with the liquid crystal inside. Injury could result. If necessary, gargle your mouth and clean your eyes or skin with clear water for at least 15 minutes and consult your doctor.
• Do not put anything on the device or cover the device with cloth, silicone, glue, coating, separate covering etc. Fire or device issues could result.
• Do not install the device in any of the following locations. Fire, electric shock, or device trouble could result.
  • Places under direct sunlight or places near heating equipment that varies in temperature.
  • Places subject to dust, oil, chemicals, hydrogen sulfide (hot spring).
  • Places subject to moisture and humidity extremes, such as bathrooms, cellars, greenhouses, etc.
  • Places where the temperature is very low, such as inside a refrigerated area or in front of an air conditioner.
  • Places subject to steam or smoke (e.g. near heating or cooking surfaces). Where noise generating devices such as dimmer switches or inverter electrical appliances are closeby.
  • Locations subject to frequent vibration or impact.
• On devices with intercom, be sure to perform a call test with low audio volume on both intercom devices. A sudden call etc. may arrive causing for example damage to your ear.
• If the device does not operate properly, unplug the power supply.
• All devices which are not marked as weather-proof are designed for indoor use only. Do not use outdoor.
• On devices which are marked weather-proof: Do not spray with high-pressure water. Device issues could result.
• We do not assume any liability for damage to property or personal injury caused by improper use or the failure to observe the
• hazard information. In such cases, any claim under warranty ceases. For consequential damages, we assume no liability!

Safety instructions

NOTICE:

• The device shall be used in compliance with local laws and regulations.
• Store the device in a dry and ventilated environment.
• Avoid exposing the device to shocks or heavy pressure.
• Do not install the device on unstable brackets, surfaces or walls. Make sure the material is strong enough to support the weight of the device.
• Use only applicable tools when installing the device. Using excessive force with tools could cause damage to the device.
• Do not use chemicals, caustic agents, or aerosol cleaners.
• Use a clean dry cloth for cleaning.
• Use only accessories that comply with technical specification of the device. These can be provided by Bird Home Automation GmbH.
• Use only spare parts provided by or recommended by Bird Home Automation GmbH.
• Do not attempt to repair the device by yourself. Contact Bird Home Automation GmbH for service matters.
• Keep the device more than 1 m (3.3‘) away from microwave, radio, TV, wireless router and any other wireless devices.
• On devices with intercom or built-in speaker or built-in microphone or signal transmission functions, keep the wires more than 30 cm (12‘‘) away from AC 100-240 V wiring. AC induced noise and/or device malfunction could result.
• Install the device in an area that will be accessible for future inspections, repairs and maintenance.
• If the device is used close to a cellular phone, the device may malfunction.
• The device can be damaged if dropped. Handle with care.
• The device turns inoperative during power failure.
• On devices with intercom or built-in speaker or built-in microphone, in areas where cellular or Radio / TV broadcasting station antennas are closeby, the device may be affected by radio frequency interference.
• On devices with LCD screen, it must be noted in advance that the LCD panel, though manufactured with very high precision techniques, inevitably will have a very small portion of its picture elements always lit or not lit at all. This is not considered a device malfunction.
• On devices with intercom, due to the environmental sound around the device, it may hinder smooth communication, but this is not a malfunction.
• On devices with Username/Password, the Username/Password to access the device is the customer‘s responsibility. Make sure to use a password that cannot be easily guessed by a third party. We recommend that you change the Password on a regular basis.
• We will, under no circumstances, be liable for damage that occurs due to failures in power supply, network equipment or terminal devices; failures due to Internet providers and cellular network providers; failures such as disconnected lines and other losses in communication, which makes it impossible to provide this service as well as in any way delay this service due to any other causes outside of our responsibility; or if an error or missing data occurs during transmission.

Transportation
When transporting the device, use the original packaging or equiva-NOTICE lent to prevent damage to the device.

Warranty Information
For information about the device warranty, see www.doorbird.com/warranty

COMPONENTS

Contents

• 1x Device
• 1x Power supply unit (mains adaptor) with four country-specific adaptors
• 1x RJ45 network cable (300 cm)
• 3x Phillips countersunk head screws
• 3x Dowels
• 3x Crimp connectors
• 1x Installation manual
• 1x Drilling template
• 1x Quickstart Guide with Digital Passport

Device

VIDEOS
Need help with the installation? Be sure to watch our installation videos which can be found on http://www.doorbird.com/support
Each individual step of the installation is clearly documented in the videos.

INSTALLATION

All steps below should be carried out carefully by a competent adult, taking into consideration any applicable safety regulations. Should you have any questions, please contact us or a competent specialist directly. Please ensure that all wires used for the installation are undamaged along their entire length and approved for this type of use.

Network speed and network components

Please ensure that the upload speed of your Internet connection is at least 0.5 Mbps. You can also carry out a speed test at any time via the DoorBird App. The user experience is only as good as your network speed, network stability and quality of your network components, such as your Internet router and WiFi access points or WiFi repeaters. Please also make sure that your network components are no more than two years old, have been manufactured by a well-known manufacturer, and have the latest firmware installed.

Should these requirements not be fulfilled, it may happen, i.e. that the performance of audio and video is poor or push notifications are delayed or do not arrive on your smartphone or tablet at all.
High-speed Internet (via landline): DSL, cable or optical fibre
Network: 802.11b/g/n 2.4 GHz or Ethernet, with DHCP

STEP 1: SWITCHING OFF POWER
Switch off the power to all wires leading to the assembly location, i.e. the door chime, electric door opener, power supply unit, PoE-Switch/ PoE- Injector etc.

STEP 2: DISMANTLING THE EXISTING DOOR CHIME
Should there already be a door chime on the wall, please do not hesitate to remove it.

STEP 3: DETERMINING THE ASSEMBLY LOCATION
The device is designed for indoor-use only.
Press the drilling template of the device against the wall or ceiling at the desired installation site and mark the boreholes with a pencil. Remove the drilling template again. Ensure that no cables are to be found in the wall or ceiling behind the boreholes.

STEP 4: DOWELS AND SCREWS
If the wall of the house is not made of wood, you should drill dowel holes 5 mm in diameter in the wall according to the drilling template and then place the dowels provided into the boreholes.

If you must drill holes in a wall, insert screws into a wall or lever up a wall, ensure that no cables or mains (gas, water, etc.) are to be found in the wall.

If the wall of the house is made of wood, dowels are not normally required. There are special dowels for assembling the device on an insulating wall, e.g. Fischer insulating dowels.
Please check with your insulating material manufacturer regarding which dowels they recommend. Use the Phillips countersunk head screws provided to position it in the dowels or on the wall, so that the countersunk head screws protrude a few millimeters above the wall.

STEP 5: PREPARING THE POWER SUPPLY
The device can be powered by two simple doorbell wires using the power-supply unit (mains adaptor) supplied with it or via PoE (Power over Ethernet) using a network cable. The device can alternatively also be supplied with a DIN-rail power supply unit that you can obtain from us directly. The device does not use battery power.

Option 1: Power supply using the power-supply unit (mains adaptor)
Two insulated wires are required to power the device by connecting it to the power-supply unit (mains adaptor) supplied with it. These wires are normally already there and are freely accessible once you have removed the previous door chime. You can also connect the power supply without any additional wires to the door chime, the power supply has a 300cm long cable with two insulated wires. If you need longer wiring, connect the wires of the power supply using the supplied crimp connectors with the two wires that you want to use for the power supply.

NOTICE:

Do not plug the power supply unit into the wall socket yet.
Only use the power supply unit provided along with the device, or a DIN-rail power supply unit that you can obtain from us separately, since this has been specially stabilized electrically and is equipped with an integrated audio interference reduction device. Other power supply units may destroy the device or cause poor transmission quality. The warranty automatically expires if you use a different power supply unit. The power supply unit is plugged into a wall socket inside your house, usually where the two wires from your previous door chime comes out of the wall in the interior of the house.

Option 2: Power supply via PoE (as an alternative)
To power the device via a PoE-Switch (e.g. D-Link DGS-1008P) or PoE-Injector (e.g. DoorBird Gigabit PoE Injector) in accordance with the PoE standard IEEE 802.3af Mode A, the four wires bearing the numbers 1, 2, 3 and 6 of a Cat.5 cable or better are to be used. A Cat.5 cable or better must be used as network signals can only be transmitted over completely insulated, shielded and twisted cables. If you use PoE as a source of power, the WiFi interface of the device is automatically inactive, and the four wires for PoE then simultaneously form the data link. The device won’t start if your PoE Switch or PoE injector does not support the PoE Standard IEEE 802.3af Mode A (see Diagnostic-LED and Diagnostic-Sounds).

1. Disconnect the PoE-Switch or PoE-Injector from the power grid.
2. Place the network cable in the installation site of the device.

NOTICE:
Do not combine the power supply from the power supply unit
(mains adaptor) with the power supply via PoE. You can find further information about PoE here: http://www.doorbird.com/poe

STEP 6: FURTHER CONNECTIONS (OPTIONAL)
If desired, connect additional wires to the installation site of the device. The wires or connection options mentioned in this section are optional.

Connecting the unit to a network
(Be sure to use **four insulated, shielded and twisted wires of a network cable in accordance with the Cat.5 standard or better. Only four wires of the network cable will be used.)**

You can connect the device to your existing network via WiFi, or alternatively use a network cable (Ethernet). For reasons of network stability, we principally recom-mend using a network cable, as WiFi is sensitive to interference (range, house walls acting as shields, relia-bility of performance, third party WiFi networks, wireless transmitters causing interference in the area, etc.).
The device can be powered by PoE or using the power supply unit provided. If you use PoE as a source of power, the WiFi interface of the device remains inactive.
Use only a network cable with RJ45 plug that meets the Cat.5 standard or a better one.
Connect the network cable to your PoE-Switch or PoE-Injector that is connected to your Internet router. Then connect it to the device.

Conventional Storey-call button (Two insulated wires.)

You can connect a conventional button to the device to realize a separate storey-call. A Storey-call button is typically used if you have more than one door, e.g. street door and apartment door. Please make sure to add no voltage on that contact.

NOTICE: Please make sure to add no voltage on these ports. Extra voltage may destroy the device immediately.

STEP 7: PREPARING THE WIRES
Remove about 5 mm of insulation material at the end of the wires that you would like to connect to the device (Power supply, Storey-call button).

STEP 8: CONNECTING THE WIRES
It is possible to connect the cables and wires to the device conveniently and safely via a connection terminal on the reverse of the device. The individual contacts on the connection terminal are labelled on the casing. You can connect all necessary cables and wires to the device using the connection terminal now. Please remove any cables and wires on the connection terminal that you do not need. Remove about 5 mm of insulation material at the end of the wires that you would like to connect to the screw connection terminal of the device.

Do not power the device simultaneously via  the
NOTICE power supply from the power supply unit (mains adaptor) and the power supply via    PoE.
15 V DC +| 15 V DC Power supply, positive pole (+)
Do not power the device simultaneously via  the
NOTICE power supply from the power supply unit (mains adaptor) and the power supply via    PoE.
STC| Storey-call button, 0 V DC/V AC, 0 A
LAN/POE| Ethernet Network cable with RJ45 plug, supports PoE
Do not power the device simultaneously via the
NOTICE **** power supply from the power supply unit (mains adaptor) and the power supply via PoE.

NOTICE: Please take care when connecting the cables and wires. Connecting the cables and wires the wrong way may destroy the device.

STEP 9: FINAL ASSEMBLY
Mount the device on the Phillips countersunk head screws you already positioned in step 3 and 4.

STEP 10: ACTIVATING THE DEVICE
Switch on the power leading to the assembly location again. If you use PoE, make sure to switch on power of the PoE-Switch or PoE-Injector you have connected the device to.

NOTICE: Do not power the device simultaneously via the power supply from the power supply unit (mains adaptor) and the power supply via PoE.

You can see if the device is powered by checking the Diagnostic-LED, which lights up after about 30 to 60 seconds after the power is connected. The device is ready for operation (booting up process, any software updates, etc.) once it has emitted a short diagnosis sound from the integrated loudspeaker. This may last for up to 5 minutes. Should you not hear a sound, please check the power supply. Please also check whether you have used a wall-plug pow-er supply and not PoE and whether you have connected the positive pole and negative pole to the device correctly.

STEP 11: DOWNLOADING AND INSTALLING THE APP
Download the “DoorBird” App by Bird Home Automation onto your mobile device from the Apple App Store or Google Play Store. You can always find the most up-to-date version of the App manual on www.doorbird.com/support.
If you use WiFi for connecting the device to your Internet router, first go to the DoorBird App “Settings → WiFi Setup” and follow the instructions.

If you have finished the WiFi setup or have connected the device to your Internet router by means of a network cable, go to the DoorBird App “Settings → Administration” and login to the video door station you would like to pair the device with. To add the device there, go to “Peripherals → Settings → Add”.
If you have problems adding the device to the App please check if the device is online ( www.doorbird.com/checkonline ). If the device is not online, please check the WiFi or network cable connection again.

DIAGNOSTIC-LED
You can see if the device is powered by checking the Diagnostic-LED, which lights up after about 30 to 60 seconds after the power is connected. The Diagnostic-LED automatically turns off after about 5 minutes.

DIAGNOSTIC-SOUNDS
After around one to five minutes, the device emits brief diagnostic sounds after it has been connected to the power grid.

TECHNICAL SPECIFICATIONS

Dimensions: 125 x 119 x 26 mm (H x W x D) 4,92 x 4,68 x 1,02 in (H x W x D)
Power Supply:
15 V DC or Power over Ethernet
(PoE 802.3af Mode-A)
Operating conditions: 0 to +55°C / 32 to 131°F
Relative Humidity
10 % to 85 % (non condensing)
Connectors: 1 x RJ45, 4 x Screw terminal
Loudspeaker: 102 dB
WiFi: 2.4 GHz, 802.11 b/g/n, internal antenna
PoE: IEEE 802.3 af/at
Housing: Polycarbonate, UV-resistant
System requirements: Mobile Device: Newest iOS on iPhone/iPad, newest Android on Smartphone/Tablet
Internet: High-Speed Landline Broadband Internet connection, DSL, cable or fiber optic, no socks or proxy server
Network: 802.11 b/g/n 2.4 GHz or Ethernet Network, with DHCP
Compatible with all DoorBird IP Video Door Stations.

Scope of delivery:

• 1 x IP Door Chime
• 1 x Network Cable
• 1 x Power supply unit (mains adaptor) with four country-specific adaptors (110 – 240 V AC to 15 V DC)
• 1 x Small parts
• 1 x Installation manual

Approvals: CE, IC, FCC, RoHS, IP50
Weight: 200 g

Errors and omissions excepted.

LEGAL NOTES

General remarks

1. DoorBird is a registered trademark of Bird Home Automation GmbH.
2. Apple, the Apple logo, Mac, Mac OS, Macintosh, iPad, Multi-Touch, iOS, iPhone and iPod touch are trademarks of Apple Inc.
3. Google, Android and Google Play are trademarks of Google, Inc.
4. The Bluetooth® word mark and logos are registered trademarks of Bluetooth SIG, Inc.
5. All other company and product names may be trademarks of the respective companies with which they are associated.
6. We reserve the right to make changes to our products in the interests of technical advancement. The products shown may also look different from the products supplied based on ongoing enhancement.
7. Reproducing or using texts, illustrations and photos from this instruction manual in any media – even if only in the form of excerpts
   • shall only be permitted with our express written consent.
8. The design of this manual is subject to copyright protection. We do not accept any liability for any errors or any erroneous content or printing errors (even in the case of technical specifications or within graphics and technical sketches).
9. Our products are in compliance with all technical guidelines, electrical and telecommunications regulations applicable in Germany, the EU and the USA.
10. Our products and also the components contained therein (ICs, software, etc.) may only be used for civilian non-military purposes.

Data privacy and data security

1. For maximum security, the device uses the same encryption technologies as are used in online banking. For your security, no port forwarding or DynDNS is used either.
2. The data centre location for remote access over the Internet by means of an App is obligatory in the EU if the determined Internet IP-Address location of the device is within the EU. The data centre is operated in line with the most stringent security standards.
3. Video, audio and any other surveillance methods can be regulated by laws that vary from country to country. Check the laws in your local region before installing and using this device for surveillance purposes.

If the device is a door-, indoor station or camera:

• In many countries video and voice signal may only be transmitted once a visitor has rung the bell (data privacy, configurable in the App).
• Please carry out the mounting in such a way that the detection range of the camera limits the device exclusively to the immediate entrance area.
• The device may come with a visitor history and motion sensor. You can activate/deactivate this function if required.

If necessary, indicate the presence of the device in a suitable place and in a suitable form.
Please observe any relevant country-specific statutory regulations concerning the use of surveillance components and surveillance cameras applicable at the installation site.
Check with the property owner and your house community if you are allowed to install and use this product. Bird Home Automation GmbH cannot be held responsible for any miss-use or miss-configuration of this product, including the unauthorized opening of a door.
Bird Home Automation cannot be held responsible for damages caused by improper existing installations or improper installation.

Software and operating system’s updates (so-called “firmware updates”) are generally automatically installed on the products of Bird Home Automation GmbH via Internet, if technically possible. Automatic firmware updates keep the products‘ software up to date so that they always work reliably, safely and efficiently. Through further development, features can be added, extended or slightly changed. Major changes or limitations to existing features will generally occur if Bird Home Automation GmbH deems it necessary (e.g. for data protection, data security or stability reasons, or to keep them up to date). When a firmware update is available, Bird Home Automation GmbH‘s servers generally automatically distribute it to all compatible products connected to the Internet or Bird Home Automation GmbH‘s servers. This process is gradual and can take several weeks. As soon as a product receives a firmware update, the system will be installed and will restart by itself. Installed firmware updates cannot be undone. Since the products and software of Bird Home Automation GmbH are not explicitly customer-specific products, a customer cannot deny an automatic update if the product is connected to the Internet or to the Bird Home Automation GmbH’s server.

Instructions for disposal
Do not dispose of the device with regular domestic waste. Electronic equipment must be disposed e.g. at local collection points for waste electronic equipment in compliance with the Waste Elec trical and Electronic Equipment Directive.

Publisher
Bird Home Automation GmbH
Uhlandstraße 165
10719 Berlin
Germany
Web: www.doorbird.com
Email: hello@doorbird.com

It is possible that these manual still contains typographical errors or printing errors.The information in this manual will be checked regularly and corrections will be made in the next version. We accept no liability for errors of a technical or printing nature and their consequences.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>