JOHN LEWIS Magnolia 8LT Pendant User Guide
- June 7, 2024
- John Lewis
Table of Contents
MAGNOLIA 8LT PENDANT
USER GUIDE
Product code 701 422220
Getting started| Thank you for purchasing this Magnolia pendant. Please
read the instructions carefully before use to ensure safe and satisfactory
operation of this product.
---|---
Warnings|
For your safety, this product must be installed in accordance with local
Building Regulations.
If in any doubt, or where required by the law, consult a competent person who
is registered with an electrical self-certification scheme. Further
information is available online or phone your Local Authority.
To prevent electric shock, switch off the mains supply before installing or
maintaining this product. Ensure other persons cannot restore the electricity
supply without your knowledge.
Always use the correct bulb type with the correct wattage as indicated in the
specification table. This product is Class I and should be fitted to a
lighting Supply protected by a 5 amp fuse or equivalent circuit breaker.
When changing the bulb, always switch off at the mains and allow the old bulb
to cool down before handling. Dispose of used bulbs carefully.
Caution! The bulb and surrounding parts can become hot during use.
For indoor use only.
Parts List
Ref
| Description|
Qty
---|---|---
A
| Mounting bracket|
1
B
| Screw fixings|
2
C
| Light fitting|
1
Product assembly
The height of the fitting is adjustable prior to electrical installation only. To adjust the length of cable, pull the metal support wire through into the ceiling cup until the desired height is achieved. If you wish to lengthen the wire again simply push the small tube that the wire passes through in on itself (it is spring loaded) and gently pull the wire back through to the desired length, as soon as the tube is released it will automatically lock in position again. With the support wire length achieved pull the supply cable through into the ceiling cup until the desired length is achieved. Ensure that the supply cable is left slack so it is the metal support wire taking all of the strain of the weight once installed and not the supply cable.
Step 1
Remove mounting bracket (A) from fitting by removing the retaining screws
and any washers, retain for later. Using the mounting bracket as a template,
mark and then drill the fixing holes in the mounting surface. (ensure the
screws (B) are firmly fixed into a solid or other suitable mounting and not
just the plasterboard) Take care not to damage wiring.
Attach mounting bracket to the mounting surface using suitable fixings. Do not
attach fitting to mounting bracket at this stage. Make sure no wires are
trapped in the process.
Step 2
Ensuring the power has been isolated, feed the household supply cable
through the black rubber sleeve of the terminal block and connect the
electrical supply wires to the connector blocks corresponding terminals.
Support the fitting weight and Make electrical connections as follows:
- Connect supply live to fitting live (marked “L”) on the terminal block.
- Connect supply neutral to fitting neutral (marked “N”) on the terminal block.
- Connect the supply earth to the earth (marked “ “) on the terminal block.
Please note that residential wiring can vary, if you are unsure about the
correct polarity please consult a qualified electrician. Ensure electrical
connections are tight and no loose strands of wire protrude from the terminal
block then close connector block cover by snapping back together. Excess cable
must be carefully located inside the ceiling cup or within the ceiling cavity
itself.
Step 3
Carefully offer fitting (C) over mounting bracket then secure in place with
the screws and any washers removed earlier. Take care not to damage the
wiring.
Step 4
Fit the bulb: type and wattage as indicated on the fitting.
The wattage indicated must not be exceeded.
Once installation is complete, the house electricity may be restored at the fuse box.
Product information| • Indoor use only
• Dimmable
• Replacement bulbs should be the same type and rating, available from John
Lewis
• Partners or other established brands Clean the fitting with a soft dry cloth
---|---
Aftercare and troubleshooting| If you experience any unresolvable technical
issues with the product, contact your nearest John Lewis & Partners shop or
John Lewis & Partner Technical Support on 03301 230106.
Why is the light not working when switched on?
Check your power supply is switched on
Turn off light and check that the bulb is inserted correctly
Check the bulb is still in working order.
Specification| Max. power: 4W LED Only (250-400 lumen) Voltage: 220–240V, 50Hz
IP rating: 20
Weight: 2.8kg
5-year guarantee| At John Lewis & Partners we test every light to high quality
standards so we are able to offer you a 5 year guarantee.
Recycling|
This symbol indicates that this product should not be treated as normal household waste and it should be recycled. John Lewis & Partners do not operate instore take back, but as members of the Distributor Take Back scheme have funded the development and upgrade of recycling facilities across the UK. Please take it to your nearest collection facility or for further details contact your local council or visit www.recycle-more.co.uk.
John Lewis Plc
171 Victoria Street
London SW1E 5NN
johnlewis.com
Made in China
IL4399 Issue 1 05/21
Please retain these instructions for future reference
References
- John Lewis & Partners | Department Store | Home, Fashion, Tech & More
- Everything you need to know to Recycle More
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>