allen roth 48-in Vanity With Top Instruction Manual

allen roth 48-in Vanity With Top Instruction Manual

ATTACH YOUR RECEIPT HERE

Serial Number__ Purchase Date__
ALLEN + ROTH and logo design are trademarks or registered trademarks of LF, LLC. All rights reserved.
welcoming • sophisticated • inspiring
Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-866-439-9800, 8 a.m. – 8 p.m., EST, Monday – Sunday.
You could also contact us at partsplus@lowes.com or visit www.lowespartsplus.com. SM20604

PACKAGE CONTENTS

HARDWARE CONTENTS (NOT SHOWN ACTUAL SIZE)

SAFETY INSTRUCTIONS

Please read and understand this entire manual before attempting to assemble, operate or install the product.

WARNING

• There are several assembly steps, including unpacking, that require two adults.

CAUTION

• DO NOT try to pry off top from vanity, as damage to top or vanity may occur.
• Follow these instructions closely, take your time, and use care while assembling this vanity.

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts with
package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.
Estimated Installation Time: 45 minutes (24 hours for silicone caulk to dry).
Tools Required for Installation (not included): Phillips screwdriver, utility knife or scissors, silicone caulk, power drill with drill bit.
Helpful Tools (not included): Measuring tape, level

INSTALLATION INSTRUCTIONS

1. Take out the top (B) and backsplash (C) according to the steps indicated by the drawings, and place them face down onto a scratch free surface such as a foam sheet that came in the
   packaging.
   
   INSTALLATION INSTRUCTIONS

2. Apply silicone caulk (not included) to the top edge of sink (K). With the help of another adult, lower the sink onto the back Make sure the sink over-flow hole is facing
   the front of stone top. Be sure to align the sink well with the stone top cut out allowing for equal stone overhang on the front, back and sides of the ceramic sink (K).side of the stone top.
   Note: To install the sink onto the top correctly, ensure that the two “BACK” stamps on the sink and the top are aligned on the same sides. Use the guide lines marked on the sink and
   bottom side of stone top to assist with sink location.
   

3. Screw bolts (GG) into the threaded holes of stone top (B).
   
   INSTALLATION INSTRUCTIONS

4. Lower the sink brackets (HH) over the bolts (GG) and allow to rest on the sink lip. Adjust location of bracket to firmly grasp sink lip. Lower lock washers (JJ) over bolts (GG) and secure with nuts (II). Hand tighten nuts (II) with included wrench (KK). DO NOT OVER TIGHTEN!
   Tip: Check that the sink placement is well centered front to back and side to side of the stone top cut out before allowing the silicone caulk to dry. If the sink is not centered well
   unscrew sink clamps, re-adjust the sink position and re-tighten the sink brackets.
   
   Hardware Used
   
   Note: Clean area where the vanity (A) will be permanently located prior to beginning installation, ensuring the vanity (A) will not interfere with any water supply and drain lines once mounted

5. With two people, carefully place vanity (A) against the wall in its final location.
   While holding the vanity base firmly against the wall, use the pre-assembled levelers on the bottom of each leg of the vanity (A) to level the item. Twisting the levelers counterclockwise
   will raise the height of the vanity (A), and twisting them clockwise will lower the vanity. Once the vanity is in place, against the wall, and level from front to back and side to side, drill a hole through the vanity mounting area and into the wall studs (as illustrated in diagram 5). Using appropriate mounting hardware (not included), secure the vanity (A) to a wall stud. If possible, secure the vanity (A) to two wall studs for increased stability.
   
   WARNING
   Vanity (A) MUST be secured to wall.
   INSTALLATION INSTRUCTIONS
   Note: At this stage it may be easier to install the faucet and drain kit (not included) to top (B) per the manufacturer’s instructions, before moving on to Step 6.

6. Apply stain free silicone caulk (not included) to the top edge of vanity (A). With the help of another adult, gently lower top (B) onto the vanity (A). Wipe away any excess caulk with a
   soft cloth, and wait approximately 24 hours for it to dry.
   

7. Apply silicone caulk (not included) to unpolished side and bottom of backsplash (C). Position backsplash (C) on top (B) and against wall. Clean any excess caulk before allowing to dry.
   
   INSTALLATION INSTRUCTIONS

8. If you need to adjust the doors, do so in the following manner.
   To adjust door up or down, loosen screws (a) on both hinges, adjust door, and retighten screws.
   To adjust door left or right, turn screws (b) on both hinges, in and out.
   To adjust door in or out, loosen screws (c) on both hinges, adjust door, and retighten screws.
   

9. As shown in the diagram, fully extend the drawer and locate the plastic levers on the metal glide tracks. Push the left-side and right-side levers at the same time to disengage the drawer from the drawer glides. Gently lift the drawer up to remove it from vanity (A).
   
   INSTALLATION INSTRUCTIONS

10. To reinstall drawer(s) into vanity (A), fully extend metal glide tracks. Gently lower and slide drawer box into rear glide catch. Next, lower drawer box down to completely rest
    on extended glides. Then, push plastic levers to lock the drawer box in place.
    Note: Drawer box alignment can be adjusted, if necessary. As shown in the diagram, spin the adjustment wheel to the left to raise the drawer box, or to the right to lower the drawer
    box. The left and right-side glide heights can also be adjusted independently in order to find the drawers best alignment position.
    
    CAUTION
    DO NOT force drawer or damage to glide(s) may occur. If drawer does not slide in with ease, remove and try again from the start. Assembly is now complete. Install desired
    faucet and drain assemblies (neither included) per the manufacturers’ instructions to complete the installation. ****

CARE AND MAINTENANCE

• Dust the vanity regularly with a soft, non-lint producing cloth or household dusting
• You can clean the vanity with a gentle, non-abrasive household
• Make sure to dry the wood immediately with a soft cloth or
• The ceramic sink can be cleaned using standard ceramic cleaning agents available at your local
• Tips for using touch-up pen (AA): For scratches, stroke in direction of scratch; for worn areas, stroke in direction of wood Rub off excess colorant promptly with a soft cloth.

IMPORTANT

• Shade variations and patterns are an inherent characteristic of stone (e.g. granite, marble, engineered stone). Stone tops will vary from product to product. Use caution placing items such as soap or any fragranced material on the stone surface. Use a soap dish, coaster or similar item to protect the surface if placing any soap or fragranced products on the
• If soap or fragranced products come in contact with the stone top, rinse the surface with water and dry using a soft non-abrasive
• WARNING: Must use cleaning agents safe for stone. Check your cleaning agents use restrictions before using on any stone. Damage to the stone may result. Vanity manufacturer not responsible for damage caused by improper cleaning agents or soaps used. Warranty will not cover damage caused by the use of improper soaps or cleaning
• DO NOT use products to clean the stone top that contain acetone, lemon, vinegar or other acids as these may cause damage to the stone surface.
• Periodically reseal the stone top using an appropriate stone sealer available from your local home Follow the manufacturer’s directions on how to apply. ****

WARRANTY

The manufacturer warrants this item against defects in materials and workmanship for a period of one (1) year from the date of original retail purchase. This warranty applies only to the original purchaser. This warranty does not apply to any damage on the product by accident, misuse, or modified, improper installation or by affixing accessories not produced by the manufacturer. The manufacturer will not be held liable for damages caused from cleaners or soaps that etch or stain the stone top. The manufacturer is not accountable whatsoever for product installation during the warranty period. There is no further expressed warranty. The manufacturer shall not be legally responsible for incidental, consequential or special damages arising at or in connection with product use or performance except as may otherwise be accorded by law. The manufacturer disclaims any and all implied warranties.

REPLACEMENT PARTS LIST

For replacement parts, call our customer service department at 1-866-439-9800, 8 a.m. – 8 p.m., EST, Monday – Sunday. You could also contact us at partsplus@lowes.com or visit
www.lowespartsplus.com.

GTC-SINK CLIPS

HH| Sink Bracket
II| Nut
JJ| Lock Washer
KK| Wrench

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>