CORSAIR 10GAK9901 Key Light User Guide

**CORSAIR 10GAK9901 Key Light User Guide

**

Federal Communication Commission Interference Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does  cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate this equipment. This equipment complies with FCC radiation exposure limits  set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and a human body.

For questions about Elgato product compliance with FCC regulations, please contact: Compliance Officer, Corsair Memory Inc., 47100 Bayside Pkwy, Fremont, CA 94538, USA

This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Elgato, a division of:
Corsair Memory Inc., 47100 Bayside Pkwy, Fremont, CA 94538, USA Corsair Memory, BV Wormerweg 8, 1311 XB, Almere, Netherlands Copyright 2018 – 2021 Corsair Memory Inc. All rights reserved. Elgato and the Elgato logo are trademarks of Corsair Memory Inc., registered in the U.S. and other countries.
Part: 51GAK9905

• R-C-CSI-20GAK9901
• R-R-SXt-A6541304000I

Set up your Key Light

Screw Key Light directly onto the pole via the integrated socket and screw. Extend the pole to your preferred height.

A non-slip rubber washer is included for mounting a camera, camcorder, etc. It is recommended that you remove it when mounting Key Light.

Do not overtighten.

• Push the button to position the ratchet after tightening.
  

• Padded and expandable up to 6 cm / 2.35 in
  

• Connect the power supply and plug it into a power outlet.
  

Installation (Software)

1. Download and install the Control Center app
   

2. Switch on your Key Light. It will take approximately 15 seconds to boot up.

3. Launch Control Center and pair Key Light by clicking the + icon.
   

4. Use Control Center to switch Key Light on/off, adjust brightness, and fine-tune color temperature.
   

Key Light requires a 2.4 GHz network with WPA or WPA2 encryption. Your  system must therefore be Wi-Fi enabled. Ensure that Key Light is within range of your computer and router.

If your PC is not equipped with Wi-Fi, use the Elgato Control Center app from the App Store or Google Play to add and control Key Light from an iOS or Android device. Wi-Fi connection is only  needed for initial pairing. Once Key Light is added to your network, you can control it via any Mac or Windows PC within your network.

Reset

Power off Key Light. Push and hold the RESET Button (II) for at least 10 seconds until the light flashes 3x. Wait a moment before switching on Key Light again.

RESET will restore your Key Light factory settings and forget all Wi-Fi credentials.

Warning

• Key Light may become hot during prolonged use. Always handle with care.
• Do not cover this product, especially the ventilation holes.
• Do not place on or near a carpet, curtains, or any other flammable materials.
• Be especially cautious when setting up near children.
• Do not attach items to Key Light or its pole.
• Do not leave the product exposed to direct sunlight.
• Do not set up in areas susceptible to strong air currents. Drafts and breezes can cause movement that may result in damage to the product.
• Keep the light free from dirt and dust. If Key Light becomes dirty, wipe it lightly with a soft cloth moistened with a little water and mild, neutral detergent. Benzene, thinner, and other volatile agents can cause permanent damage and should never be used for cleaning.
• Always mount the pole to a level, stable surface. Uneven or unstable surfaces may cause tipping and result in damage or personal injury.
• Do not use the pole for applications other than those specified in this guide or the packaging

Frequency range: 2412 – 2472 MHz (2462 MHz for FCC, ISED), Max RF e.i.r.p power < 20 dBm, Temperature range: 0 °C – 45 °C. Hereby, Corsair Memory Inc. declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EC.
The declaration of conformity for Elgato products is available at www.elgato.com/doc

References

• Declaration of Conformity

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>