ANKER PowerDrive 2 Alloy User Manual
- June 7, 2024
- Anker
Table of Contents
USER MANUAL
PowerDrive 2 Alloy
Using Your Product
For the fastest and safest charge, use an Anker® cable, your device’s original cable, or another certified cable (such as MFi).
Important Safety Instructions
- SAVE THESE INSTRUCTIONS– This manual contains important safety and operating instructions for car charger Model A2727.
- Before using a car charger, read all instructions and cautionary markings on the car charger.
- Do not expose the charger to rain, moisture, or snow.
- Use of an attachment not recommended or sold by the car charger manufacturer may result in a risk of fire, electric shock, or injury to persons.
- To reduce the risk of damage to the cigarette lighter connector and ord, pull by the cigarette lighter connector rather than the cord when disconnecting the charger.
- Make sure the cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress.
- Do not operate charger with damaged cord or cigarette lighter connector – replace it immediately.
- Do not operate the charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified serviceperson.
- Do not disassemble the charger; take it to a qualified service person when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire.
- To reduce the risk of electric shock, unplug the charger before attempting any maintenance or cleaning. Turning off controls will not reduce this risk.
- To reduce the risk of fire or electric shock, do not interconnect output terminations
- CAUTION – For continued protection against the risk of fire, replace only with the same type and ratings of fuse, fuse rating 32Vdc, 7A or 63Vdc, 7A.
- The maximum ambient temperature during the use of the appliance must not exceed 40°C.
SAVE THESE INSTRUCTIONS
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio / TV technician for help.
The following importer is the responsible party (for FCC matters only).
Company Name: Fantasia Trading LLC
Address: 9155 Archibald Avenue, Suite 202, Rancho Cucamonga, CA, 91730, US
Telephone: +1 (909) 484 1530
This device complies with Industry Canada license-ICES-003. Operation is
subject to the following two conditions:
(1) This device may not cause interference, and (2) This device must accept
any interference, including interference that may cause undesired operation of
the device.
Declaration of Conformity
Hereby, Anker Innovations Limited declares that the product type A2727 is in
compliance with Directive 2014/30/EU & 2011/65/EU. The full text of the EU
declaration of conformity is available at the following internet address:
https://www.anker.com.
Anker Innovations Limited | Room 1318-19, Hollywood Plaza, 610 Nathan
Road, Mongkok, Kowloon, Hong Kong
Anker Innovations Deutschland GmbH | Georg-Muche-Strasse 3-5,
80807 Munich, Germany
Anker Technology (UK) Ltd | Suite B, Fairgate House, 205 Kings Road,
Tyseley, Birmingham, B11 2AA, United Kingdom
Specifications
| Input| DC 12 / 24V
---|---|---
| Output| 5V 4.8A (2.4A Max Per Port)
| Size| 1.76 × 1.0 × 1.0 in / 44.7 × 25.2 × 25.2 mm
| Weight| 0.7 oz / 20 g
Customer Service
| 18-month limited warranty *
---|---
| Lifetime technical support
| support@anker.com
| (US) +1 (800) 988 7973 Mon – Fri 9:00am – 5:00pm (PT)
(UK) +44 (0) 1604 936200 Mon – Fri 6:00 – 11:00 (GMT)
FAQs and more information, please visit:
anker.com/support
@Anker
@Anker Japan
@Anker Deutschland
@AnkerOfficial
@Anker_JP
@anker_official
@anker_jp
Product Number A2727
51005001950 V03
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>