STARSPACE BTX-290 Office Chair Instruction Manual

June 6, 2024
STARSPACE

STARSPACE BTX-290 Office Chair Instruction Manual

ASSEMBLY GUIDE

Congratulations, you are now the owner of a brand new STARSPACE chair!

Following this assembly guide and you will find a quick start guide to assemble your STARSPACE chair. We highly recommend checking out our Assembly Videos as well for even more detailed and visual instructions.

If you run into any difficulty during the assembly, remember to check out the assembly Video to see if you’ve missed anything. If you’re unable to resolve your problems, drop us an email as well and our support team will assist you.

PACKAGE LIST

  1. Back Cushion *1
    PACKAGE LIST

  2. Seat Cushion *1
    PACKAGE LIST

  3. Arms *2
    PACKAGE LIST

  4. Seat Plate *1

  5. Back Pillow *1
    PACKAGE LIST

  6. Lift *1
    PACKAGE LIST

  7. Lift Cover *1
    PACKAGE LIST

  8. Star Base *1
    PACKAGE LIST

  9. Casters *5

  10. Bolts 1/41” 4

  11. Bolts 5/163/4” 3

  12. Bolts M845mm 4

  13. Plastic Caps *4

  14. Wrench *1

ASSEMBLY INSTRUCTION

Step 1: Turn the Star Base(8) upside down, then press the Casters(9) into the holes at the end of each base leg, insert the Lift(6) into the center hole of the StarBase, the Lift Cover(7) should be placed over the Lift.

ASSEMBLY INSTRUCTION

Step 2: Align the Seat Plate(4) over the pre-drilled holes underneath the Seat Cushion, make sure that the front of the seat plate is facing the front of the Seat Cushion. Attach the Seat Plate(4) to the Seat Cushion(2) using FOUR Botls 1/4*1”(10) , tighten all the bolts with the Wrench(14), being careful not to missthread the bolts or damaged the seat.

ASSEMBLY INSTRUCTION

Step 3: Turn the Seat Cushion upright and align the center hole of the Seat Plate(4) over the lift, then push the Seat Cushion(2) down onto the lift firmly until the connection is secure.

Step 4: Attach Seat Cushion and Back Cushion, align the Steel Plate over the predrilled holes with Three Bolts 5/16*3/4”(11), tighten all the bolts with the wrench(14).

ASSEMBLY INSTRUCTION

Step 5: Using the Seat Plate to tilt 135°angle Locking, then tighten the zipper between seat cushion and back cushion, then tilt angle back to 90°.

Note 1: Arm rests are labeled with an “L” (left) or “R” (right) to show which sides they should be placed on.

ASSEMBLY INSTRUCTION

Step 6: Attach the Arms(3) to the Seat Cushion(2) and Back Cushion(1) with Four Bolts M8*45mm(12), using the Wrench(14).

ASSEMBLY INSTRUCTION

Step 7: Press the Plastic Caps(13) into the Arms holes to cover the bolts.

ASSEMBLY INSTRUCTION

CAUTION:

Make sure all bolts and screws are fully tightened before using chair. Lubricate all moving parts and tighten all bolts/ screws every 6 month or whenever needed.

INSTRUCTIONS FOR USE

  1. Seat Height:Paddle-First lever on the right side
    INSTRUCTIONS FOR USE
    To raise:
    While taking your weight off chair, lift lever up.
    To lower:
    While seated, lift lever up.

    • At the proper height, your feet should rest flat on the floor.
  2. Operating the tilt lockout-the second lever on the right side
    INSTRUCTIONS FOR USE
    Push down to lock the tilt person mechanism.
    Pull up to unlock the tilt mechanism.

    • At the proper height, your feet should rest flat on the floor.
  3. Built-in adjustable lumbar support
    INSTRUCTIONS FOR USE
    The built-in adjustable lumbar support with controlled lumbar knob effectively relieves pressure from the lumbar region.

SAFETY AND MAINTENANCE

  • Do not stand on the chair, Do Not use the chair as stepladder.
  • Use this product for seating one person at a time.
  • Do not use the chair unless all bolts and screws are firmly secured.
  • Avoid contact with sharp objects to prevent puncturing the fabric.
  • Every 6 months, check all bolts and screws to ensure they are tight.
  • To clean, spot clean only using a damp towel and mild cleaner, first test on a small, obscure area of fabric.
  • Chair weight limit not to exceed 350 lbs.

SAFETY INFORMATION

  • Sit in the center of the chair,with your back to the backrest.
    SAFETY INFORMATION

  • Do not sit at the front edge of the chair.
    SAFETY INFORMATION

  • Do not stand on the chair.
    SAFETY INFORMATION

  • Do not use the chair with more than one person .
    SAFETY INFORMATION

  • Do not push the chair around when a person is sitting in it.
    SAFETY INFORMATION

  • Do not push down on the backrest when a person is reclined.

  • Do not place all your weight on the backrest only.
    SAFETY INFORMATION

LIMITED WARRANTY

STARSPACE promises to repair or replace any STARSPACE chair that is found to be defective in material or workmanship within one (1) year from the date of original purchase so long as you, the original purchaser, still owns it. This is your sole and exclusive remedy. This warranty is subject to the provisions below.

EXCLUSIONS

This warranty does not apply and no other warranty applies to:

  • Normal wear and tear, which are to be expected over the course of ownership.
  • Misuse, abuse or excessive use of the product.
  • Modifications or attachments to the product that are not approved by STARSPACE.
  • Products that were not installed, used, or maintained in accordance with product instructions and warnings.
  • Products used for rental or commercial purposes.
  • Damage caused by the carrier in-transit is handled under separate terms.

Seating Usage: Normal use for seating is identified as the equivalent of a single shift, forty- (40) hour workweek. To the extent that a seating product is used in a manner exceeding this, the applicable warranty period will be reduced in a pro-rata manner.

Some retailers might have custom models imported direct from the factory and therefore are not supported by our local service team because we don’t have the correct parts, please contact your retailer directly for support. If you have any questions about that we will be happy to assist and identify those items.

RETURN POLICY

We adopt a 30 days return policy which means that all products purchased on this
website may be returned to us within the time frame. You need to contact us within
30 days after the product(s) came into your possession and the product(s) must be
returned to us without any undue delays.

Returned products must be returned in the same condition as they were sent and they must be sent in its original packaging.

If the product is not faulty, (i.e. if you changed your mind or if you are unhappy with the product for some other reason), the cost of shipping will fall on you. And it is your responsibility that the package arrives safely to us so we recommend that you use a courier service where it is possible to track the shipment.

If the product is faulty when you receive it please contact us and we will help you out.

We reserve the right to give a partial refund in cases when the product(s) is not in an unused condition, is damaged or have missing parts not due to our error.

HOW RETURNS WORK:

Contact us through the contact form on our website and attach the invoice to the message as a proof of purchase. And please also write the reason for return.

We will then get back to you as soon as possible with information on where to send the product(s).

As soon as we have received the product(s) and made an inspection we will inform you of our decision.

If a refund is approved we will automatically credit the purchase to your credit card or original method of payment.

Before you get started, a few pointers:

  • Having a friend to help makes assembly extra-easy
  • Mind the important safety information
  • Contact us if you have any issues

Customer Support

can this QR Code to watch our assembly video for the chair
QR Code

phone: +1 628-222-2513
Email: service@starspacechair.com
Web: http://www.starspacechair.com/

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals