LAEGENDARY RC Monster Car User Manual

June 6, 2024
LAEGENDARY

RC Monster Car

TABLE OF CONTENTS
Introduction …………………………………………………………………………………….4 Terms of Use ……………………………………………………………………………………5 Safety Precautions ……………………………………………………………………..6-8 What’s in the Box……………………………………………………………………………9 Quick Start. Getting up to Speed…………………………………………..10-16 Operation and Troubleshooting ……………………………………………17-20 WARRANTY……………………………………………………………………………………21 Replacement Parts …………………………………………………………………22-27 Anatomy of the LEGEND………………………………………………………28-33 CE Compliance & FCC …………………………………………………………………34

Introduction

Terms of use

INTRODUCTION

TERMS OF USE

Thank you for purchasing the LEGEND truck. Incredible speed, efficient operation and long run times are just some of the benefits. This manual contains the instructions you will need to operate and maintain your model so that you can enjoy it for years to come. However, please be advised that this model is a hobby-grade RC car which will require maintenance and replacing parts. Rest assured that LAEGENDARY is a team of professionals who aim to provide the highest level of factory support possible. We know you’re excited about getting your new model on the road, but it’s very important that you take some time to read through the Owner’s Manual. This manual contains all the necessary setup and operating procedures that will allow you to unlock the performance potential that LAEGENDARY engineers designed into your model. Also, be sure to read and follow the precautions and warnings in this manual and on any labels or tags attached to your model. They are there to educate you on how to operate your model safely and also get maximum life and performance from your model. Even if you are an experienced R/C enthusiast, it’s important to read and follow the procedures in this manual. Thank you again for choosing LAEGENDARY. We work hard every day to assure you receive the highest level of customer satisfaction possible. We truly want you to enjoy your new model!
You can find all replacement parts on our website at www.laegendary.com
If you have any questions about your model or its operation, call LAEGENDARY Customer Support at 646 859-1050 or E-mail: support@laegendary.com.

This product is surrendered by LAEGENDARY to the purchaser with the understanding that the purchaser accepts the responsibility that driving this model and using the enclosed accessories in a careless, improper, or unsafe manner can result in serious injury or death. Also, the purchaser assumes all liability resulting from any misuse, unsafe handling, failure to follow instructions, or any action that constitutes a violation of any applicable laws or regulations. LAEGENDARY shall not be liable for personal injury, loss of property, or loss of life resulting from the use of this product under any circumstances, including intentional, reckless, negligent, or accidental behavior. LAEGENDARY shall also not be liable for any special, indirect, incidental, or consequential damages arising out of the assembly, installation, or use of their products or any accessory or chemical required to use their products. By the act of operating/using the product, the user accepts all resulting liability and releases LAEGENDARY of any and all liability associated with its use. If you as the user do not accept liability of ownership, LAEGENDARY requests that you do not use this product. Do not open any of the enclosed materials. Return the model to LAEGENDARY but please be advised that we absolutely cannot accept an item for return or exchange after it has been run or is otherwise no longer in as-new condition.
All information contained in this Owner’s Manual is subject to change without notice. LAEGENDARY reserves the right to make changes and improvements to products without incurring any obligation to incorporate such improvements into products previously sold. If you have any questions about your model or its operation, call LAEGENDARY Customer Support at 646 859-1050 or E-mail: support@laegendary.com.

Safety Precautions
Safety Is Your Responsibility!
WARNING: RISK OF INJURY!
Do not stand directly behind the car while driving to avoid personal injury from rocks, sticks, or other thrown objects, especially during full throttle starts. Keep any spectators and animals at a safe distance. Wearing eye protection is recommended.
WARNING! CAUTION! DANGER! FIRE HAZARD!
CHARGING AND DISCHARGING BATTERIES HAS THE POTENTIAL FOR FIRE, EXPLOSION, SERIOUS INJURY, AND PROPERTY DAMAGE IF NOT PERFORMED AS PER THE INSTRUCTIONS. BEFORE USE, READ AND FOLLOW ALL MANUFACTURER’S INSTRUCTIONS, WARNINGS AND PRECAUTIONS. NEVER ALLOW CHILDREN UNDER THE AGE OF 14 TO CHARGE OR USE THE BATTERIES WITHOUT THE SUPERVISION OF A RESPONSIBLE, KNOWLEDGEABLE ADULT. DO NOT LEAVE THE BATTERIES OR CHARGER UNATTENDED WHILE CHARGING.
CHARGING AND HANDLING PRECAUTIONS
· DO NOT let any exposed battery contacts or wires touch each other. This will cause the battery to short circuit and create the risk of fire. · While charging, ALWAYS place the battery on a nonflammable surface such as concrete. · NEVER charge batteries on wood, cloth, carpet or on any other flammable material. · ALWAYS charge batteries in a well-ventilated area. · REMOVE flammable items and combustible materials from the charging area. · DO NOT place objects on top of the charger or batteries. · If any battery or battery cell is damaged in any way, do NOT charge, discharge, or use the battery. · DO NOT disassemble, crush, short circuit, or expose the batteries or cells to flame or any other source of ignition. · If a battery gets hot to the touch during the charging process, disconnect the battery from the charger and discontinue charging immediately. · ALWAYS unplug the charger and disconnect the batteries when not in use. · DO NOT leave the charger and batteries unattended while charging, discharging, or any time that the charger is ON with batteries connected. If there are any signs of a malfunction or in the event of an emergency, unplug the charger from the power source and disconnect the batteries from the charger. · REMOVE the batteries from your car before charging. · DO NOT expose the batteries and charger to water or moisture. · ALWAYS store battery packs safely out of the reach of children and pets.

www.LAEGENDARY.com

34

www.LAEGENDARY.com

www.LAEGENDARY.com

56

www.LAEGENDARY.com

Safety Precautions
· DO NOT charge batteries under ANY of the following conditions: – Batteries that are hot to the touch. – Batteries that are not expressly stated by the manufacturer to be suitable to accept the power output (voltage and amperage) the charger delivers during the charging process. – Batteries that are damaged or defective in any way. Examples of damage or defects include, but are not limited to, batteries with dented cells, damaged or frayed wires, loose connections, fluid leaks, corrosion, plugged vents, swelling, cell deformity, impact damage, melted components, or any other signs of damage. – Battery packs that have been altered from original manufacturer configuration. – Non- rechargeable batteries (explosion hazard). – Batteries that have missing or unreadable labels, preventing you from properly identifying the battery type and specifications.
IMPORTANT POINTS TO REMEMBER
· Because your model is controlled by radio, it is subject to radio interference from many sources that are beyond your control. Since radio interference can cause momentary losses of radio control, always allow a safety margin in all directions around the model in order to prevent collisions. · Range test your radio system in the area that you will be running the model to ensure that you have range that covers the area you want to drive. After range testing, drive slowly in the area at first to make sure there is no interference that can cause momentary lapses of control. · Always use new or freshly charged batteries in your model to maximize signal power output and range. · The motors, batteries, and speed control can become hot during use. Be careful to avoid getting burned. · Choose the right location to drive. Your model is absolutely not intended for use on public roads or congested areas where its operation can conflict with or disrupt pedestrian or vehicular traffic. This is to prevent the possibility of injury or death resulting from collision with the model by another human being or animal. · Do not drive the RC car by yourself. Bring a friend along to act as a spotter to alert you if a person or animal is approaching. · Do not operate your model at night, or anytime your line of sight to the model may be obstructed or impaired in any way. · Do not drive the model close to you where a mistake or loss of control could cause the model to collide with you or any spectator. · Always carefully inspect your model for damage or loose components before running. Do not drive the model if it is damaged in any way. Tighten any loose hardware. · Never pick up the model by its tires or wheels. Always keep your hands safely clear of moving parts whenever the batteries are plugged in.

Safety Precautions
· Keep the RC car stored with the batteries removed, out of the reach of children and protected from access by any other unauthorized driver. · Always disconnect the batteries in the model when it is not in use. Never store the vehicle with batteries in the model, as this can cause a fire leading to property damage, serious personal injury or even death. · Do not continue to operate the model with low batteries or you could lose control of it. Indications of low battery power include slow operation and delayed vehicle response. Stop immediately at the first sign of weak batteries. When the batteries in the transmitter become weak, the red power light will begin to flash. Stop immediately and install new batteries. · Most importantly, use good common sense at all times.
SPEED CONTROL
Your model’s electronic speed control (ESC) is an extremely powerful electronic device capable of delivering high current. Please closely follow these precautions to prevent damage to the speed control or other components. · Disconnect the Battery: Always disconnect the battery or batteries from the speed control when not in use. · Insulate the Wires: Always insulate exposed wiring with heat shrink tubing to prevent short circuits. · Transmitter on First: Switch on your transmitter first before switching on the speed control to prevent runaways and erratic performance. · Don’t Get Burned: The ESC and motor can become extremely hot during use, so be careful not to touch them until they cool. Supply adequate airflow for cooling. · No Reverse Voltage: The ESC is not protected against reverse polarity voltage.

What’s in the box? WHAT’S IN THE BOX?
TOP DESIGN MAY VARY, DEPENDING ON THE MODEL YOU PURCHASED

Quick Start

QUICK START. GETTING UP TO SPEED

REMOVE THE TRUCK BODY

Pull out the pins and remove the body

Make sure all accessories are properly attached, remove the protection film from the body before turning on the truck.
CHARGE AND INSTALL RECHARGEABLE BATTERY PACK
1. USB Charger Lights Indicator: a) The power light turns solid red when plugged in the outlet b) The green light flashes when the battery is connected c) The green light turns solid when charging is complete

2 USB chargers

Plug adaptor

Wrench tool

Remote control

2 Batteries

Battery safety bag

User manual

www.LAEGENDARY.com

78

www.LAEGENDARY.com

www.LAEGENDARY.com

9 10

www.LAEGENDARY.com

Quick Start

2. Loosen the latches of the battery cover to open it.

3. Place your fully charged battery in the battery slot. Connect the battery connector. Do not force it! It only goes one way!

Quick Start

INSTALL TRANSMITTER BATTERIES
1.Remove the battery cover. Press down on the top of the cover and on the arrow at the bottom of the cover, while sliding the cover off in the direction of the arrow. (Figure 1) 2. Install 3 x 1.5V AA batteries (not included) in correct polarities. (Figure 2) 3. Slide back the battery cover. (Figure 3)

USB CHARGER PRECAUTIONS
CAUTION!
The USB Charger does not support an input current higher than 4A. When the input current is higher than 4A, the USB charger will enter into the protection mode, and all the lights will turn off.

Quick Start

Quick Start

TRANSMITTER INSTRUCTIONS

4. Replace the battery cover to the bottom of the car and close the battery compartment door.

INSTALL LED WIRE 1. Pass the LED wire through the body bracket. 2. Lock the LED into the front and rear bumper. Connect the wire to the ESC socket.

TIGHTEN THE WHEEL
Tighten the wheel nuts before each running session and periodically check the tightness of the wheel nuts while you are running.

A. Power Switch B. Steering Trim C. Steering Dual Rate Adjustment D. Steerig Reverse Switch E. Speed Mode (Full Speed And Half Speed Mode)

ESC Socket

(Figure 1)

(Figure 2)

(Figure 3)

NOTICE 1. When installing batteries, please be sure to match the polarities labeled on the battery holder. 2. Do not mix old and new batteries. 3. Do not mix different types of batteries.

www.LAEGENDARY.com

11 12

www.LAEGENDARY.com

1. Turn on the power switch on the transmitter,red LED will flash. 2. When pairing successful with the car, red LED and blue LED will turn solid.
Blue LED will flash when power is low on the transmitter, please replace batteries before continuing.

www.LAEGENDARY.com

13 14

www.LAEGENDARY.com

1. Forward 2. Brake 3. Left 4. Right 5. Backward

Quick Start

Quick Start

TRANSMITTER SWITCH INSTRUCTIONS
A. Power Switch
When pairing for the first time, both the car and the transmitter have to be turned on within 3 seconds, to pair the frequency. The blue LED and red LED on the transmitter will turn solid when pairing is successful. At the same time, the LED on the car will turn solid.
B. Steering Trim

D. Steering Reverse Switch
(Figure 9)
(Figure 10)
· When the switch is on NOR, turn the steering wheel clockwise and the car will turn to the right. Turn the steering wheel counter clockwise, and the car will turn to the left. (Figure9) · When the switch is on REV, turn the steering wheel clockwise and the car will turn to the left. Turn the steering wheel counter clockwise and the car will turn to the right. (Figure10)
E. Speed Mode (Full Speed And Half Speed Mode)

When the chassis switch is turned on and the front tires are not straight, use the ST. TRIM to adjust the position. · when the car oversteers to the left, ST. TRIM should be adjusted clockwise. · when the car aversteers to the right, ST. TRIM should be adjusted anticlockwise.
C. Steering Dual Rate Adjustment

SR. D/R knob can be set to control the steering throw. · turning the ST. D/R knob clockwise to increase the steering throw, the maximum angle is 48°. · turning the ST. D/R knob anticlockwise to reduce the steering throw, the minimum angle is 10°.

Suggestion: To avoid damaging the car, please turn the switch to half speed mode (L) when you play the car for the first time!
The default setting for the speed mode is “L” (half speed mode). When you want to begin your high speed experience, please set it to “H” full speed mode).

H
Full speed mode

L
Half speed mode

· Switch on H: full speed mode (the speed is about 48 km/h) · Switch on L: half speed mode (the speed is about 26 km/h)

www.LAEGENDARY.com

1516

www.LAEGENDARY.com

Operation

Troubleshooting

OPERATION
1. Always turn on your transmitter before you turn on the receiver in the vehicle. Always power off the receiver before turning your transmitter off.

2. ALWAYS operate your vehicle in a wide open area. Operating the vehicle on slippery floor or indoors may cause the vehicle to crash due to high speed.

3. WARNING! The water level should be lower than the bottom of the truck. If excessive amount of water gets into the body of the truck and causes damages or other related problems, we will not be responsible for any such damages.
The customer will be responsible for any replacements and additional accessories if needed.

4. ALWAYS start with low speed, or the vehicle may slip or run on curves (as shown on Pic 1). NEVER operate your vehicle in max speed. Operating the vehicle in max speed may hurt yourself and damage the vehicle.
Start
Half
Start Half Speed
High High Speed
MOTOR CARE
· Seat the motor brushes by driving smoothly on a flat surface during use of the first battery charge. Failing to do so can greatly reduce motor performance and functional life. · Prolong motor life by preventing overheating conditions. Undue motor wear results from frequent turns, stops and starts, pushing objects, driving in deep water and tall grass, and driving continuously up hill.

TROUBLESHOOTING

PROBLEM
Scratched top
Steering not working properly

SOLUTION
The RC car comes with a protective plastic film that needs to be removed prior to using the car. If a new truck shell is needed, it can be ordered through our website www.laegendary.com
1. Replace the batteries of the remote with brand new ones and fully charge the car battery.
2. Turn off the switch on the transmitter, then on, and pair again. Make sure not to touch the throttle when pairing. 3. Clean the steering arm set and make sure the arm is still in place, connected to the car.
4. Check the light of the transparent wire coming out of the car; it should be a solid red.
5. Unplug the wires connecting the servo and the ESC, then pair the car with the transmitter again. This is to check the defective part; if the car pairs with the remote, then the servo might be the problem.
6. Servo and remote controller can be ordered through our website www.laegendary.com

Reverse command not responding
Car going on its own and not responding correctly

When the car is moving forward in order to go in reverse please execute the following commands on the remote: first throttle push will bring the car to a stop and in neutral mode. The second throttle push will make the car go in reverse. (please refer to Transmitter Instructions in this User Manual)
Do not press any buttons on the remote control while pairing with the car because it will recognize that command every time. Rebind the remote and car and turn them on within 3 seconds so you reset the commands and car responds properly.

www.LAEGENDARY.com

1718

www.LAEGENDARY.com

Troubleshooting

PROBLEM
Car will not pair with the remote
Wheels are not spinning properly
Stripping sound upon accelerating

SOLUTION
1. Our LEGEND car has a thermal protection feature. When the ESC detects that the temperature is too high, it will automatically start thermal protection. Thus, it needs to be switched off and wait for a few minutes to cool the temperature down.
2. Keep the remote and the car a few feet away from each other while pairing.
3. Keep the remote and the car away from large metal objects while pairing so there is no interference.
1. Tighten the locknuts (Part Number LG-WJ02) that are holding the wheels in place.
2. Check for any missing pieces like hub hex with shafts (Part Number LG- ZJ09) and/or rear dog bone (Part Number LG-WJ05). If parts are missing, they can be ordered through our website www.laegendary.com
3. If all parts are intact, the differential may be broken and needs to be replaced.
1. Inspect the car and make sure all the pieces are in place and no foreign objects were caught up in it. Please refer to the schematic in this User Manual to properly check the parts.
2. Check the front and rear differentials (Part Number LG-ZJ06) if they are functioning properly with both the axels and main drive shaft. Make sure that the gears of either the differential and/or main drive shaft (Part Number LG- ZJ05) are not stripped.

Troubleshooting

PROBLEM
Battery/charger not working
Rebinding the remote control with the car

SOLUTION
1. Solid red light on the charger ­ charger is plugged in.
2. Blinking red light ­ charger is defective.
3. Blinking green light on the charger ­ battery is plugged in and charging.
4. Solid green light on the charger ­ battery is fully charged.
5. Blinking green light after 3-4hrs of charging ­ battery is defective.
6. Please try charging the battery using the second USB charger to determine which is defective.
Replacement batteries and chargers can be purchased through our website www.laegendary.com
Turn on the remote control first and within 3 seconds turn on the car as well in order to rebind them; if not successful, repeat this action 2-3 times. If the pairing is still not successful, the remote and/or the ESC needs to be replaced.

Warranty

LAEGENDARY WARRANTY

To guarantee you have the best experience we offer a 1 year warranty covering defects in materials, workmanship and assembly on all our products*. To ensure that you don’t invalidate the terms of the warranty please read and understand this booklet.

*If a defect in materials, workmanship or assembly is found BEFORE the product has been used, we will exchange the entire product, if the product is returned complete and in perfect condition in its original packaging. **

IT IS THE PARENTS’ OR GUARDIANS’ RESPONSIBILITY TO ENSURE MINORS RECEIVE APPROPRIATE GUIDANCE AND/OR SUPERVISION WHEN USING OR WORKING ON THIS PRODUCT.

THIS IS A COMPLEX HIGH PERFORMANCE RC MODEL AND MUST BE TREATED WITH CARE AND RESPECT. LAEGENDARY has made every effort to ensure your product is as strong and durable as posible. However, it is still possible to break or cause damage by crashing or misuse. Most rc car parts are consumables and will wear with use (servo, differential, tires, shafts, bumpers, shocks, arms etc). More extreme or frequent use will increase the wear rate of these components. Always check these parts before and after using your car and replace before failure. All the parts of this car are available to be purchased separately, or as small sets, to allow you to get years of use from your RC truck. The bodyshell is not just for looks, it is also designed to protect vital areas of the running gear and electronics from damage.

LAEGENDARY DOES NOT operate a new for old warranty once the product has been used. Once the product has been used we offer a component level warranty and will replace the defective component(s) at our discretion.

Warranty is only valid if the items were purchased direclty from LAEGENDARY (purchases from third party sellers will not be covered under the warranty)

COVERED BY WARRANTY – 1 year warranty for the Motor (excludes damages caused by the user, including but not limited to incorrect maintenance.) – 6 months warranty for the Electronic Speed Controller (excludes damages caused by the user, including but not limited to incorrect maintenance.)

NOT COVERED BY WARRANTY

– All other parts not mentioned above, such as but not limited to: Servo, Differential, Shocks, Axels,

Arms, Wheels, etc

– Component failure or premature wear as a result of crash damage

– Lack of maintenance, improper use or abuse

Half

– Water damage or problems resulting from water intake

– Bodyshells once they have been painted and/or used

** In many cases it is faster and more cost effecHtiigvhe for the user to fit replacement parts to the product so we maintain the right to request this of the user.

Replacement parts are available for sale on our website at : www.laegendary.com

Replacement Parts REPLACEMENT PARTS

No. LG-SJ01 BR

Product Name Car shell

Specifications –

Quantity

1×1

Remarks

No. LG-SJ01 BY

Product Name Car shell

Specifications –

Quantity

1×1

Remarks

No. LG-SJ01 RO

Product Name Car shell

Specifications –

Quantity

1×1

Remarks

No. LG-SJ01 YP

Product Name Car shell

Specifications –

Quantity

1×1

Remarks

No. LG-SJ01 CL

Product Name Car shell

Specifications –

Quantity

1×1

Remarks

No. LG-SJ03

Product Name Car shell bracket

Specifications –

Quantity

1×2

Remarks

No. LG-SJ04

Product Name Front bumper block

Specifications –

Quantity

1×1

Remarks

No. LG-SJ05

Product Name Rear bumper block

Specifications –

Quantity

1×1

Remarks

No. LG-SJ06

Product Name Front upper arm

Specifications –

Quantity

1×2

Remarks

No. LG-SJ07

Product Name Rear upper arm

Specifications –

Quantity

1×2

Remarks

No. LG-SJ08

Product Name Front lower arm

Specifications –

Quantity

1×2

Remarks

No. LG-SJ09

Product Name Rear lower arm

Specifications –

Quantity

1×2

Remarks

www.LAEGENDARY.com

19 20

www.LAEGENDARY.com

www.LAEGENDARY.com

21 22

www.LAEGENDARY.com

Replacement Parts

Replacement Parts

No. LG-SJ10

Product Name Front steering cup

Specifications –

Quantity

1×2

Remarks

No. LG-SJ11

Product Name Rear knuckle

Specifications –

Quantity

1×2

Remarks

No. LG-SJ12

Product Name Shock proof plank

Specifications –

Quantity

1×2

Remarks

No. LG-ZJ01

Product Name Steering arm set

Specifications –

Quantity

1×1

Remarks

No. LG-ZJ02

Product Name Tire

Specifications –

Quantity

1×2

Remarks

with sponge inserts

No. LG-ZJ03

Product Name Shock absorbers

Specifications –

Quantity

1×2

Remarks

No. LG-SJ13

Product Name Connecting rod

Specifications –

Quantity

1×3

Remarks

includes steering ball head

No. LG-SJ14A

Product Name Car chassis

Specifications Quantity
Remarks

1×1 for RC car model without LED lights

No. LG-SJ14B

Product Name Car chassis

Specifications –

Quantity

1×1

Remarks

for RC car model with LED lights

No. LG-ZJ04

Product Name 5 wires servo

Specifications –

Quantity

1×1

Remarks

No. LG-ZJ05

Product Name

Main drive shaft assembly

Specifications –

Quantity

1×1

Remarks

No. LG-ZJ06

Product Name Differential

Specifications –

Quantity

1×1

Remarks

No. LG-SJ15A

Product Name Battery compartment

Specifications –

Quantity

1×1

Remarks

for RC car model without LED lights

No. LG-SJ15B

Product Name Battery compartment

Specifications Quantity
Remarks

1×1 for RC car model with LED lights

No. LG-SJ16

Product Name Front cover

Specifications –

Quantity

1×1

Remarks

No. LG-ZJ07A

Product Name

Electronic speed controller

Specifications –

Quantity

1×1

Remarks

for RC car model without LED lights

No. LG-ZJ07B

Product Name

Electronic speed controller

Specifications –

Quantity

1×1

Remarks

for RC car model with LED lights

No. LG-ZJ08

Product Name 2.4G transmitter

Specifications –

Quantity

1×1

Remarks

No. LG-SJ17

Product Name Rear cover

Specifications –

Quantity

1×1

Remarks

No. LG-SJ18A

Product Name Battery cover

Specifications Quantity
Remarks

1×1 for RC car model without LED lights

No. LG-SJ18B

Product Name Battery cover

Specifications –

Quantity

1×1

Remarks

for RC car model with LED lights

No. LG-ZJ09

Product Name

Aluminum alloy wheel hub hex

Specifications –

Quantity

1×4

Remarks

No. LG-WJ01

Product Name Arm connector set

Specifications –

Quantity

1×3

Remarks

No. LG-WJ02

Product Name Locknut

Specifications –

Quantity

1×4

Remarks

www.LAEGENDARY.com

23 24

www.LAEGENDARY.com

Replacement Parts

Replacement Parts

No. LG-WJ03

Product Name

Front CVD drive shaft set

Specifications –

Quantity

1×2

Remarks

No. LG-WJ04

Product Name Transmission cup

Specifications –

Quantity

1×2

Remarks

No. LG-WJ05

Product Name Rear dog bone

Specifications –

Quantity

1×2

Remarks

No. LG-LS10

Product Name

Countersunk head screw

Specifications 2.6 x 8KBHO

Quantity

1×10

Remarks

No. LG-LS12

Product Name Round-headed screw

Specifications 2.6 x 20PBHO

Quantity

1×10

Remarks

No. LG-LS14

Product Name Round-headed screw

Specifications 2.5 x 6 x 5PWMHO

Quantity

1×10

Remarks

No. LG-WJ06

Product Name Shell pin

Specifications –

Quantity

1×8

Remarks

No. LG-WJ07

Product Name Motor fasteners

Specifications –

Quantity

1×1

Remarks

No. LG-WJ08

Product Name Shaft

Specifications –

Quantity

1×2 / 1×2

Remarks

No. LG-LS16

Product Name Round-headed screw

Specifications 3 x 31PMHO

Quantity

1×4

Remarks

No. LG-LS17

Product Name Round-headed screw

Specifications 3 x 36PMHO

Quantity

1×4

Remarks

No. LG-DJ01

Product Name 390 motor

Specifications –

Quantity

1×1

Remarks

includes gear

No. LG-WJ09

Product Name Bearing

Specifications 6.3 x 9.5 x 3

Quantity

1×4

Remarks

No. LG-WJ10

Product Name Bearing

Specifications 8 x 13 x 3.5

Quantity

1×4

Remarks

No. LG-LS01

Product Name Round-headed screw

Specifications 2.6 x 10PBHO

Quantity

1×10

Remarks

No. LG-DJ02

Product Name Li-PO

Specifications 7.4V 1600mAh

Quantity

1×1

Remarks

No. LG-DJ03

Product Name USB charger

Specifications –

Quantity

1×1

Remarks

No. LG-DJ04

Product Name Battery connector

Specifications –

Quantity

1×1

Remarks

No. LG-LS02

Product Name Round-headed screw

Specifications 2.6 x 13.5PBHO

Quantity

1×10

Remarks

No. LG-LS08

Product Name Round-headed screw

Specifications 2.3 x 16PBHO

Quantity

1×10

Remarks

No. LG-LS09

Product Name Round-headed screw

Specifications 2.6 x 7PBHO

Quantity

1×10

Remarks

No. LG-DJ05

Product Name Plug adaptor

Specifications –

Quantity

1×1

Remarks

No. LG-DJ06

Product Name Battery bag

Specifications –

Quantity

1×1

Remarks

No. LG-DJ07

Product Name Velcro strap

Specifications –

Quantity

1×1

Remarks

www.LAEGENDARY.com

25 26

www.LAEGENDARY.com

No. LG-DJ08

Product Name LED lights

Specifications –

Quantity

1×1

Remarks

No. LG-DJ09

Product Name Hexagon nut wrench

Specifications –

Quantity

1×1

Remarks

Replacement Parts

Anatomy of the LEGEND

LG-LS07 LG-SJ12
LG-LS09 LG-LS09
LG-LS09 LG-LS09
LG-LS07

LG-LS10

LG-WJ01

www.LAEGENDARY.com

27 28

www.LAEGENDARY.com

LG-WJ01 LG-WJ01

LG-SJ03 LG-SJ03

LG-ZJ07B

LG-LS02
LG-LS02 LG-LS02

LG-LS12 LG-LS12

LG-LS12 LG-LS12

LG-SJ16

LG-LS09

LG-LS09

LG-ZJ04

LG-ZJ04

LG-LS12

LG-LS12

LG-LS12 LG-LS12

LG-LS12

LG-LS12

LG-SJ12

LG-SJ17

Anatomy of the LEGEND

LG-LS07

LG-LS09 LG-LS09

LG-LS09 LG-LS07

LG-DJ01

LG-WJ07

LG-LS14

LG-DJ01

LG-LS14 LG-WJ07

Anatomy of the LEGEND

LG-ZJ06

LG-ZJ05 LG-SJ14B

LG-ZJ01

LG-SJ13

LG-LS10 LG-LS10

LG-LS10 LG-LS10

LG-LS10

LG-LS10

LG-LS10 LG-LS10

LG-ZJ06

No. LG-ZJ05 No. LG-ZJ06

www.LAEGENDARY.com

29 30

www.LAEGENDARY.com

LG-LS02

LG-ZJ09 LG-WJ09 LG-SJ11 LG-WJ09

LG-ZJ09

LG-WJ08 LG-SJ07
LG-WJ08

LG-WJ09

LG-LS08

LG-SJ10

LG-WJ09

LG-WJ04

LG-WJ05

LG-SJ09 LG-SJ08

LG-SJ06

LG-SJ13

LG-WJ03

LG-LS17

LG-LS08

LG-LS02

LG-ZJ03

LG-SJ08

LG-ZJ03

LG-LS08 LG-LS16
LG-LS17 LG-LS08

LG-LS16 LG-LS16

LG-ZJ03

LG-LS17 LG-SJ07

LG-LS08

LG-ZJ03

LG-WJ05

LG-WJ04

LG-ZJ03

LG-LS08

LG-SJ06 LG-LS02

LG-SJ13 LG-WJ03
LG-ZJ03

LG-LS16 LG-LS17

LG-ZJ09

LG-ZJ09

LG-SJ08

LG-WJ09

LG-LS08 LG-SJ10 LG-WJ09
LG-ZJ09

LG-SJ09

LG-WJ09

LG-WJ08 LG-SJ11

LG-WJ09

LG-ZJ09

LG-WJ08

LG-LS02

Anatomy of the LEGEND

Anatomy of the LEGEND

LG-WJ02

LG-WJ02

LG-ZJ02 LG-LS10

LG-SJ18B LG-LS10

LG-SJ15B

LG-SJ04

LG-LS10

LG-ZJ02

www.LAEGENDARY.com

31 32

www.LAEGENDARY.com

LG-WJ02

Anatomy of the LEGEND

CE Compliance & FCC

LG-ZJ02

CE COMPLIANCE & FCC

LG-LS01

LG-SJ05

LG-LS10 LG-ZJ02

LG-WJ02

Please help the environment by disposing of your product responsibly at the end of its life. The wheeled bin symbol indicates that this product should not be disposed of in your household waste containers. Instead, the product should be disposed of by using a designated collection point for the recycling of waste electrical and electronic equipment, The Waste of Electrical and Electronic Equipment(WEEE) Directive (2002/96/EC) requires that the best available recycling techniques be employed to minimize the impact on the environment. Recycling electronics helps by keeping harmful chemicals out of the environment, and also saves money by reusing precious metals. Remove any batteries and dispose of them and the product at your local authority’s recycling facility. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or the location where you purchased this product.
Declaration of Conformity for RED Directive In accordance with IEC 17050-1
This is to certify that the following products conform to the requirements of the RED Directive 2014/53/EU and that all essential test suites have been carried out.

Changes or modifictions not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,there is no guarantee that inteference will not occur in a particular installation. IF this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receive
is connected. · Consult the dealer or experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful inteference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

www.LAEGENDARY.com

33 34

www.LAEGENDARY.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals