ResMed 37207 AirSense 10 AutoSet CPAP Machine User Guide
- June 6, 2024
- ResMed
Table of Contents
Air Sense™10
AUTOSET
AUTOSET FOR HER
ELITE
CPAP
Quick start guide
Read your entire AirSense™ 10 User Guide before use.
Setup
|
---|---
- Place the device on a stable level surface.
- Plug the power connector into the rear of the device. Connect one end of the power cord into the power supply unit and the other end into the power outlet.
| 
---|--- - Connect the air tubing firmly to the air outlet located on the rear of the device.
- Connect the free end of the air tubing firmly onto the assembled mask. Press Start/Stop to begin therapy.
AirSense 10 with HumidAir
If you have an AirSense 10 device with HumidAir™, fill the humidifier as
follows:
| 
---|---
- Open the humidifier and fill it with water up to the maximum water level mark.
- Close the humidifier and insert it into the side of the device.
Heated humidification offers relief from dryness and congestion and is
designed to make therapy more comfortable. If you do not have an AirSense 10
device with HumidAir, consider purchasing
HumidAir and ClimateLineAir™ heated air tubing.
Adjusting to therapy
If you are a first-time user, you might need some time to get used to therapy.
This is not unusual as it takes most patients between one and two weeks to
adjust to the air pressure.
Overcoming symptoms by changing comfort settings
If you are having difficulties getting used to therapy, use the AirSense 10
comfort features to help you on your journey to better sleep.
-
Trouble falling asleep— If you are having trouble falling asleep with high pressure, turn on Auto Ramp or increase Ramp Time.
-
Bloated feeling— If you are experiencing a slightly bloated feeling from swallowing air, turn on Auto Ramp or increase Ramp Time.
-
Feeling of not getting enough air— If you feel like you are not getting enough air, turn Ramp Time to Off.
To change the Ramp Time:
**1. Press the dial to enter My
Options.
2. Turn the dial to highlight Ramp Time and then press to select it.
**3. Turn the dial to adjust to your preferred setting.
4. Press the dial to save the change.
If you have an AirSense 10 device with HumidAir, you have more comfort features available which help make your therapy more comfortable. -
Dry or runny nose— If you are getting a dry or runny nose, adjust the Humidity Level by turning it up.
-
Droplets of water (condensation)— If you are getting droplets of water on your nose, mask, or air tubing, adjust the Humidity Level by turning it down.
Cleaning
-
Wash the air tubing in warm water using mild detergent.
Do not wash in a dishwasher or washing machine. -
Rinse the air tubing thoroughly and allow it to dry out of direct sunlight and/or heat.
-
Wipe the exterior of the device with a dry cloth.
If you have an AirSense 10 device with HumidAir, clean the humidifier as per
steps 1 and 2.
Refer to your mask User Guide for detailed instructions on cleaning your mask.
Checking and replacing your parts regularly
It is important for your comfort and health that you check and replace your
parts and supplies regularly. Replacing your parts and supplies on a regular
basis helps ensure you are receiving optimal
therapy and continued comfort.
Refer to your AirSense 10 User Guide for detailed instructions on checking
your device. Contact your care provider for information on your replacement
schedule.
| Serial number | Device number |
|---|---|
| Mask type and size | Date of setup |
Notes
ResMed Pty Ltd
1 Elizabeth Macarthur Drive Bella Vista NSW 2153 Australia
See www.resmed.com for other ResMed locations
worldwide. For patent information, see
www.resmed.com/ip.
AirSense, ClimateLine, and HumidAir are trademarks of ResMed. ClimateLine is
registered in U.S. Patent and Trademark Office.
© 2020 ResMed. 378942/1 2020-11
References
- Sleep apnea and COPD - learn about symptoms and treatment | ResMed
- Legal disclaimers and intellectual property - ResMed
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>