Xiaomi BHR4089GL True Wireless Earphones 2 Basic User Manual
- June 6, 2024
- Xiaomi
Table of Contents
Xiaomi BHR4089GL True Wireless Earphones 2 Basic User Manual
Read this manual carefully before use, and retain it for future reference.
Product Overview
Illustrations of product, accessories, and user interface in the user manual are for reference purposes only. Actual product and functions may vary due to product enhancements.
Instructions
Charging
-
Charging the earphones
When the earphones are placed in the charging case, they will automatically start charging. -
Charging the charging case
The indicator of the charging case is white during charging, and goes off once it is fully charged.
Checking Battery Level
-
Checking the battery level of the earphones
Aer connecting the earphones to a phone, you can check the earphones battery level on the phone’s status bar.
Note: The phone’s status bar always displays the battery level of the earphone with the lowest battery level. This feature is not supported by some phones. -
Checking the battery level of the charging case
Open the lid of the charging case, or place the earphones into the charging case:
- When the indicator light of the charging case stays lit for 5 seconds, it means the battery is sufficient.
- The indicator of the charging case is blinking white, which indicates that the baery level of the charging case is low. Please charge it immediately.
Checking the battery level by a Mi phone
Aer successfully connecting to a phone, place the earphones into the charging
case and close its lid. Make sure the Bluetooth function is enabled on your Mi
phone. Hold your phone close to the charging case, then open the case’s lid. A
notification will appear on the phone, then you can check the battery level of
the earphones and the charging case.
Note: When checking the battery level on your phone, please update your Mi phone to the latest stable version. This feature is currently only supported by some Mi phones.
Turning On
When opening the charging case, the earphones will automatically turn on.
Note: When using the earphones for the first time, place them in the charging case and close the lid to activate them.
Sleep Mode
Place the earphones back into the charging case and close the lid, the
earphones will disconnect and go into sleep mode automatically.
Wearing
Take the earphones out of the charging case, and insert them into your ears
according to the le (L) and right (R) marks.
Note: Aer using the earphones, place them back into the charging case. This will extend their lifespan and help you avoid losing or misplacing them.
Connecting
Connecting the earphones to a new device
- Place the earphones into the charging case, press and hold the touch area of either earphone for 3 seconds. The indicator of the earphones is blinking white, and the earphones are waiting for a connection.
- Enable the device’s Bluetooth, then locate and connect to “Mi TW
Earphones 2 Basic”. If a passcode is requested, enter “0000”.
● Connecting the earphones with a Mi phone
Place the earphones into the charging case and close its lid. Make sure the
Bluetooth function is enabled on your Mi phone. Hold your phone close to the
charging case, then open the case’s lid. Follow the on-screen instructions of
the phone to connect to the earphones.
Note: The feature of fast connection is currently only supported by some Mi phones, please update your Mi phone to the latest stable version.
● Connection interrupted
When your device is out of wireless range of the earphones or its Bluetooth
function is disabled, the earphones will automatically enter the awaiting
connection mode. If the earphones are not connected to any device within five
minutes, they will enter sleep mode.
● Automatic connection
When the earphones are in the charging case, opening the lid of the charging
case will automatically connect the earphones to the most recently used
Bluetooth device. If the earphones are not connected to any device within five
minutes, they will enter sleep mode.
Note: If the earphones cannot automatically connect to a device, you will need to manually connect the earphones to the desired device via the device’s Bluetooth settings.
Due to the connection characteristics of the Bluetooth signal, in dense environments with 2.4 GHz electromagnetic signal interference, there may be occasional disconnects or no sound.
Clearing connection history
- Place the left and the right earphone into the charging case.
- Simultaneously press and hold the touch areas of the left and the right earphones for seven seconds, then release the touch areas once the indicators of the earphones light up in white.
- The earphones have been reset and the connection history has been cleared. The indicators of the earphones blink white, and the earphones are waiting for a connection.
Function Overview
Notes:
- The voice assistant function can be used only if your device supports it, and this function needs to be granted permission on the device.
- When only using the le earphone, place the right earphone into the charging case and close the lid.
Specifications
- Model: TWSEJ08WM Net Weight: 48 g Input: 5 V 1 A
- Charging Port: Type-C Impedance: 32 Charging Time: Approx.1.5h
- Wireless Connectivity: Bluetooth 5.0
- Bluetooth Profiles: BLE/HFP/HSP/A2DP/AVRCP
- Supported Audio Codecs: SBC/AAC
- Wireless Range: 10 m (open space without obstacles)
- Earphones’ Battery Life (standalone): Approx. 5 h
- Total Battery Life (with charging case): Approx. 20 h
- Bluetooth Operation Frequency: 2402–2480 MHz (for EU)
- Maximum Transmit Power for BT: 10 dBm (for EU)
- Maximum Transmit Power for BLE: 10 dBm (for EU)
WEEE Information
All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as terms and conditions of such collection points.
Hereby, Tiinlab declares that the radio equipment type
TWSEJ08WM is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the
following internet address:
http://www.mi.com/global/service/support/declaration.html
Safety Caution
- Do not expose baeries or baery packs to excessive heat such as sunshine, fire or the like.
- Replacement of a baery with an incorrect type that can defeat a safeguard (such as catching fire, explosion, leakage of corrosive electrolyte etc).
- Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion.
- Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas.
- A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.
- Risk of explosion if battery is replaced by an incorrect type.
- Dispose of used batteries according to the instructions.
- The product operation maximum ambient temperature is 40°C.
To prevent possible hearing damage, do not listen at high volume levels for long periods
The symbol indicates DC voltage
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
The device is too small to bear the label information, and we list the label contents on package and user manual as well.
The marking information is located at the boom of apparatus.
FCC ID : 2ASDITWSEJ08WM
IC: 24662-TWSEJ08WM
HVIN: V7
CAN ICES-3(B)/NMB-3(B)
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Xiaomi Inc. is under license. Other trademarks and trade names are those of their respective owners.
Manufactured for: Xiaomi Communications Co., Ltd.
Manufactured by: Tiinlab Acoustic Technology Limited (a Mi Ecosystem
company)
Address: Tianliao Building 1403, Tianliao Industrial Area A, Taoyuan
Street, Nanshan District, Shenzhen 518055, China
For further information, please go to www.mi.com
Read More About This Manual & Download PDF:
References
- Xiaomi United States | Xiaomi Official Website
- 服務條款及細則 - 香港官網
- 服務條款及細則 - 小米官網
- Xiaomi Global Home
- Xiaomi Global Home
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>