dB KL12Q Active Speaker User Manual
- June 6, 2024
- dB
Table of Contents
www.dbtechnologies.com info@dbtechnologies‐aeb.com
Quick start user manual Section 1
The warnings in this manual must be observed together with the “USER MANUAL
– Section 2”.
Le avvertenze nel presente manuale devono essere osservate congiuntamente al
“MANUALE D’USO – Sezione2”.
Die Warnungen in diesem Handbuch müssen in Verbindung mit der
“BEDIENUNGSANLEITUNG – Abschnitt 2” beobachtet werden”.
Les avertissements specifiés dans ce manuel doivent être respectés ainsi que
les “CARACTERISTIQUES TECHNIQUES Section 2”
Las advertencias del presente manual see deben tener en cuenta
conjuntamente con las del “MANUAL DEL USUARIO” – Sección 2”.
A.E.B. Industriale Srl Via Brodolini, 8 Località Crespellano 40053 VALSAMOGGIA
BOLOGNA (ITALIA)
Tel +39 051 969870 Fax +39 051 969725
www.dbtechnologies.com info@dbtechnologies-
aeb.com
Thank you for choosing a dBTechnologies Product!
The SYA 12 is a versatile active speaker. It is equipped with one 1” compression driver (1.35” voice coil), and one 12” woofer (2.5” voice coil). The multiple input pattern allows easy and versatile use. For example, the user can connect a dynamic microphone (CH1), an independent source from a mixer (CH2), a Bluetooth MP3 reader (CH3), controlling each volume level. The user can enhance lower and upper frequencies with the convenient DSP preset function. Balanced link output allows the audio connection to a second loudspeaker, choosing among “Mix” or “Line” output types.
Check the site www.dbtechnologies.com for the complete user manual!
1) Unpacking
The box contains:
N°1 SYA 12
N°1 Mains cable (VDE)
This quick start and warranty documentation
2) Easy installation
SYA 12 is equipped with:
perfect for gigging bands as well as small venues installations. The 36 mm pole-mount predisposition is designed for use on a standard pole stand (like a tripod).
A –Upper integrated handle
B – Lateral integrated handles
C – Pole mount hole, with two tilt angles selection (0°/ 7.5°)
NEVER USE THE HANDLES TO SUSPEND THE SPEAKER!
Those mechanical particulars were thought of for easy use and for different configuration needs. SYA 12 is perfect for gigging bands as well as small venues installations. The 36 mm pole-mount predisposition is designed for use on a standard pole stand (like a tripod).
The acoustical design allows facing different environments. The dispersion
pattern is shown in the upper picture. As described, the related pattern data
are:
a) vertical coverage: 60°
b) horizontal coverage: 90°
The rear side
inclination, symmetrical, as shown in the upper picture, is 45°. SYA12 can be
used as a stage monitor in small contexts, in this case, please consider the
characteristic dispersion pattern presented above.
IT IS MANDATORY TO READ AND FULLY UNDERSTAND THE COMPLETE USER MANUAL FOR THE
ADMITTED
CONFIGURATIONS OF THE PRODUCT, SAFETY INFORMATION, AND THE PROPER USE OF
ACCESSORIES (IF ANY).
3) Connections, controls, first turn on
All the connections and controls are in the amplifier panel side:
CH1:
1–Audio Combo Input (for XLR or TRS connectors)
2–Line/Mic selector
3–Mic/Line Volume Control CH2:
4–Audio Input (Balanced / TRS)
5–Line Volume control CH3 (Bluetooth ):
6–BT status sync LED
7–BT Volume Control MASTER SECTION
8–DSP Preset switch
9–Balanced audio output
10–Link/Mix switch
11–Master Volume with control LEDs MAINS SECTION
12–VDE MAINS INPUT
13–ON-OFF SWITCH
a) Connect the audio input (1). The combo connector allows a TRS or XLR
connection. In case of a dynamic microphone, plug it and select “Mic” in the
Audio input sensitivity switch (2). In the other cases check that the switch
is set on “Line”. Adjust the level of Volume (3). b) Connect a second input,
depending on the kind of connection (XLR/TRS), then adjust the related volume
level.
c) If needed, enable with the switch (7) the Bluetooth receiver. Pair it with
a visible device (ex. an MP3 reader).
d) If you need to link SYA 12 to another one, please use a cable with XLR
connectors (not supplied). Connect the Link output (9) of the first, to the
balanced Input
(1) of the second one. In the second loudspeaker, please check that Selector
(2) is set on the “Line” position and that Volume (3) is set to the correct
value.
e) Set properly the DSP preset switch (8), choosing between “Playback”,
”Flat”, Bass Boost” or “Wedge” configuration.
e) Plug properly the mains VDE input cable (supplied) in the related input
(12). Check that the audio source is set on the minimum level. Then switch the
POWER switch (13) to “ON” position. Increase gradually the volume of the audio
source to the desired level. Check the site
www.dbtechnologies.com for further
information, for added accessories, and for the complete user manual!
Technical Data
Speaker Type: 2-way active speaker
Usable Bandwidth [-10 dB]: 53 – 20000 Hz
Frequency Response [-6 dB]: 58 – 19500 Hz
Max SPL (1 m): 127 dB
HF compression driver: 1 ” Exit
HF voice coil: 1.35”
LF: 12”
LF Voice Coil: 2.5”
Crossover frequency: 1700 Hz (24 dB/oct)
Horizontal dispersion: 90°
Vertical dispersion: 60°Amplifier
Amp: Custom made
Amp Class: Class-D + A/B– Active Fan cooling
RMS Power: 800 W
Operating voltage (factory set):
220-240V~ (50-60Hz) or
110-120V~ (50-60 Hz)
| Processor and user interface
Controller: 28/56 bit
AD/DA Conversion: -24 bit, 48 kHz
Limiter: Peak, RMS, Thermal
Controls: Line/mic, Channel Volume, Link/Mix, Presets
Input / Output
Mains connections: VDE
Signal Inputs: 3 channels (Combo, XLR+trs, Bluetooth )
Signal Out: (Balanced) 1x XLR OUT (LINK)
Mechanics
Housing: Polypropylene
Grille: Full metal grille
Pole Mount: Yes, 36 mm (0°/7.5° selectable)
Handles: 3 (2 on sides. 1 on the top)
Width: 365 mm (14.37 in)
Height: 622 mm (24.51 in)
Depth: 342 mm (13.46 in)
Weight: 16.5 kg (36.37 lbs).
---|---
http://www.dbtechnologies.com/qrcode/000073/
Scan with your QR Reader App to download the complete User Manual
POWER SUPPLY SPECIFICATIONS (POWER ABSORPTION)
Draw at 1/3 of full power in maximum use conditions 0’1: 1.1 A (220-240V1 –
1.7 A (100-120V-)
** INSTALLER NOTES: The values refer to 1/3 of full power, in heavy operating
conditions (music program with frequent clipping or activation of the
limiter). We recommend sizing according to these values in case of
professional installations and tours.
Download the complete user manual from the site:
www.dbtechnologies.com/EN/Downloads.aspx
EMI CLASSIFICATION
According to the standards EN 55032 and EN 55035, this equipment is designed
and suitable to operate in class B electromagnetic environments.
FCC ID: 2ADDV-TLSYA12
FCC CLASS B STATEMENT ACCORDING TO TITLE 47, PART 15, SUBPART B, §15.105
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the
equipment.
The Bluetooth® word mark and logos are registered trademarks owned by
Bluetooth® SIG, Inc. and any use of such marks by AEB
Industriale SRL is under license. Other trademarks and trade names are those
of their respective owner.
RED CERTIFICATION
Hereby, AEB Industriale declares that the KL loudspeaker is in compliance with
Directive 2015/53/EU, in reference to the following
harmonized standards:
Health & Safety EN 62479 / EN 62368-1+A11
EMC EN 301 489-1 V2.2.0, EN 301 489-9 V2.1.1, EN 55032, EN 55035
Spectrum EN 300 328 V2.1.1
SIMPLIFIED EU DECLARATION OF CONFORMITY
The full text of the EU declaration of conformity is available at the
following internet address:
http://www.dbtechnologies.com/en/downloads
Features, specifications,s, and appearance of products are subject to change
without notice.dBTechnologies reserves the right to make changes or
improvements in design or manufacturing without assuming any obligation to
change or improve products previously manufactured.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>