Armacost 713420 Proline RGB Color LED Controller With RF Remote Control User Guide
- June 6, 2024
- Armacost
Table of Contents
Armacost 713420 Proline RGB Color LED Controller With RF Remote Control User Guide
Introduction
This LED controller is designed to drive constant voltage RGB LED products such as LED tape light or LED fixtures in a voltage range of 5–24 volts DC. The receiver works with the RF wireless remote control, which allows the user to choose between multiple colors, adjust the LED brightness, and select dynamic effects.
Receiver & wiring
1. Input – from power supply
The controller input and output voltage range is 5–24 volts DC. Make sure the LED lighting voltage is within this range and below the rated wattage of the power supply. Connect input wires from the power supply to the controller as indicated by the polarity markings on the controller (+ to + and – to –).
2. Output – to LED lighting
Observe polarity indicated on the controller when connecting to LED lighting (+ to +, G to G, R to R, and B to B).
Make sure the voltage of the LED lighting is the same as the power supply and
the maximum load doesn’t exceed that of the controller.
CAUTION: Shorting of output cables could cause permanent damage to controller.
Make sure cables are well insulated from each other.
3. Controller status indicator
This light shows the controller status as follows:
Steady green: Normal working mode
Single green blink: Command received
Long single green blink: Mode or color cycle limit reached
Long single yellow blink: Brightness or speed limit reached
Red flash: Overload protection
Yellow flash: Overheat protection
Green flash 3 times: New remote control paired
4. Wiring diagram
Connect the power supply to the controller input and the controller output to the LED lighting. The output voltage of the power supply must be the same as the voltage of the LED lighting. Make sure all power cables are connected securely and insulated before powering on.
Remote Control
5. On / Off
Press the “|” key to turn on controller or the “0” key to turn off. The controller will remember the controller state when powered off, and will return to that state when powered back on.
6. RGB color setting
Press the “COLOR+” and “COLOR–” keys to scroll through all the color options. The colored keys are shortcuts for preset colors. Press the and the keys to adjust color brightness.
7. Dynamic effects
Press “MODE+” and “MODE–” to select the dynamic effect mode and “SPEED+” and “SPEED–” to adjust the effect speed.
Press the “DEMO” key to play the dynamic effects.
8. Remote indicator
When pressing keys, the indicator blinks if the remote is working properly. If the indicator flashes slowly when pressing keys, battery power is low and it needs to be replaced. Replace with a CR2032 battery.
Remote control operation
9. Using the remote control
Pull out plastic battery insulation tab before use. The RF wireless remote will work through walls and doors. Do not install in a metal enclosure.
10. Pairing with a new remote control
The remote control and receiver are already paired, but up to 5 remotes can be paired to one receiver.
To pair a new remote:
- Disconnect power to receiver and wait five seconds.
- Reconnect power and wait ten seconds.
- Press the “SPEED–” and “SPEED+” keys simultaneously for about three seconds until the remote indicator flashes quickly
11. De-pairing remotes
To de-pair a remote control, pair the remote you wish to continue using with the controller and any other paired remotes will be de-paired.
Safety Protection
The controller has a function to prevent it from being damaged by mis-wiring, output short circuit, overloading, or overheating. It will automatically shut down under these extreme conditions until safe operating conditions are restored. To avoid shutdowns, make sure the installed LED lighting is compatible with constant voltage driving, is in the rated range of the controller, and the cables are well connected and insulated. Also, install the controller with proper ventilation and heat dissipation in mind.
Specifications
Customer support
Email: support@armacostlighting.com
Phone: 410-354-6000
Monday–Friday, 9 a.m.–5 p.m., ET
Warranty
Limited 1-year warranty. This product is for dry location use only. Improper installation, improper powering, abuse, or failure to use this device for its intended purpose will void warranty. Proof of purchase is required for all returns. Questions? Email support@armacostlighting.com.
© 2020 Armacost Lighting. All rights reserved. 201001
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>