Armacost LIGHTING 513125 ProLine CCT Tunable White LED Controller User Manual
- May 15, 2024
- Armacost LIGHTING
Table of Contents
Armacost LIGHTING 513125 ProLine CCT Tunable White LED Controller
Specifications
- Product Name: ProLine CCT Tunable White LED Controller with RF Remote Control
- Model Number: 513125
- Input Voltage: 100/230V AC
- Output: LED Lighting
Product Usage Instructions
Receiver & Wiring
Make sure the voltage of the LED lighting matches the power supply. Avoid
exceeding the maximum load of the controller. Insulate cables properly to
prevent shorting.
Controller Status Indicator
The indicator light provides information on the working status of the
controller, such as normal operation, command received, mode or color cycle
edge, brightness limit, overload protection, overheat protection, and remote
controller pairing status.
Wiring Diagram
Connect the power supply to the controller input and the controller output
to the LED lighting. Ensure all power cables are securely connected and
insulated before powering on.
Remote Control Operation
Pull out the plastic battery insulation tab before use. The RF wireless
remote works through walls and doors but should not be installed in a metal
enclosure.
Pairing with a New Remote Control
- Unplug power to the receiver and wait five seconds.
- Reconnect power and within ten seconds press the ON and keys simultaneously until the remote indicator flashes quickly.
Safety Protection
This product is for dry location use only. Improper installation, powering,
abuse, or use for unintended purposes will void the warranty. Proof of
purchase is required for returns.
FAQ
-
What should I do if the controller status indicator shows a red flash?
A red flash indicates overload protection. Check and reduce the load on the controller to prevent damage. -
How can I increase or decrease LED brightness using the remote control?
Press the brightness control buttons on the remote to increase or decrease LED brightness.
ProLine CCT Tunable White LED Controller
With RF Remote Control
Model # 513125
Introduction
This LED controller is designed to work with constant voltage CCT Tunable White LED products such as LED tape light or LED fixtures in a voltage range of 12–24 volts DC. The receiver works with the RF wireless remote control, which allows the user to adjust LED brightness and select color temperature.
Receiver & wiring
-
Input – from power supply
The controller input and output voltage range is 12–24 volts DC. Make sure the LED lighting voltage is within this range and below the rated wattage of the power supply. Connect input wires from the power supply to the controller as indicated by the polarity markings on the controller (+ to + and – to –). -
Output – to LED lighting
Observe polarity indicated on the controller when connecting to LED lighting (+ to + and – to –).
Make sure the voltage of the LED lighting is the same as the power supply and the maximum load doesn’t exceed that of the controller.
CAUTION : Shorting of output cables could cause permanent damage to controller. Make sure cables are well insulated from each other. -
Controller status indicator
This light shows the working status of the controller.
It shows different events as following:- Steady green: Normal operation
- Single green blink: Command received
- Long single green blink: Mode or color cycle edge
- Long single yellow blink: Reach brightness limit
- Red flash: Overload protection
- Yellow flash: Overheat protection
- Green flash 3 times: New remote controller paired
-
Wiring diagram
Connect the power supply to the controller input and the controller output to the LED lighting. The output voltage of the power supply must be the same as the voltage of the LED lighting. Make sure all power cables are conected securely and insulated before powering on.
Remote Control -
On
Press to turn controller on. -
Off
Press to turn controller off. The controller will remember the controller state when powered off, and will return to that state when powered back on. -
Color selection
Cycles through color temperatures. -
Favorites
When on a selected color press and hold to set that color to one of the four buttons. -
Brightness control
Press to increase LED brightness and press to decrease it. -
Remote indicator
When pressing keys, the indicator blinks if the remote is working properly. If the indicator flashes slowly when pressing keys, battery power is low and it needs to be replaced. Replace with a CR2032 battery.
Remote control operation -
Using the remote control
Pull out plastic battery insulation tab before use. The RF wireless remote will work through walls and doors. Do not install in a metal enclosure. -
Pairing with a new remote control
The remote control and receiver are already paired, but up to five remotes can be paired to one receiver.
To
pair a new remote: -
Unplug power to receiver and wait five seconds.
-
Reconnect power and within ten seconds press the ON and keys simultaneously until the remote indicator flashes quickly.
-
De-pairing remotes
To de-pair a remote control, pair the remote you wish to continue using with the controller and any other paired remotes will be de-paired.
Safety Protection
The controller has a function to prevent it from being damaged by mis-wiring,
output short circuit, overloading, or overheating.
It will automatically shut down under these extreme conditions until safe
operating conditions are restored. To avoid shutdowns, make sure the installed
LED lighting is compatible with constant voltage, is in the rated range of the
controller, and the cables are well connected and insulated. Also, install the
controller with proper ventilation and heat dissipation in mind.
Specifications
- Output mode …………………………………………… PWM constant voltage
- Working voltage …………………………………………………….. 12–24V
- DC Rated output current …………………………………………………….. 1x10A
- Brightness grade ………………………………………………………..11 levels
- PWM frequency ……………………………………………………………..1KHz
- PWM physical grade …………………………………………………. 256 steps
- Overload protection …………………………………………………………… yes
- Overheat protection …………………………………………………………… yes
- Remote frequency …………………………………………………. 433.92MHz
- Remote control range ……………………. up to 50 ft./ 15m in open areas
- Controller dimensions …….. 3.43 X 0.95 X 0.59 in. / 87 X 24 X 15mm
- Remote dimensions …………. 5.27 X 1.4 X 0.38 in./ 134 X 36 X95mm
Customer support
- Email : support@armacostlighting.com
- Phone : 410-354-6000
- Monday–Friday, 9 a.m.–5 p.m., ET
Warranty
3-year limited warranty. This product is for dry location use only. Improper installation, improper powering, abuse, or failure to use this device for its intended purpose will void warranty. Proof of purchase is required for all returns. Questions? Email support@armacostlighting.com.
armacostlighting.com
© 2022 Armacost Lighting. All rights reserved.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>