Armacost 631470 RibbonFlex Pro 18 Inch Weatherproof Red-Green or Blue LED Tape Light Instruction Manual

June 5, 2024
Armacost

Armacost-631470-RibbonFlex-Pro-18-Inch-Weatherproof-Red-Green-or-Blue-
LED-Tape-Light-LOGO

Armacost 631470 RibbonFlex Pro 18 Inch Weatherproof Red-Green or Blue LED

Tape Light

Armacost-631470-RibbonFlex-Pro-18-Inch-Weatherproof-Red-Green-or-Blue-LED-
Tape-Light-PRODUCT

Please read completely before installing.
It is important to read these guidelines completely to understand how LED tape lighting works and how it can be configured and installed so you can properly design your lighting layout.
Installing tape lighting is an easy DIY project. However, basic wiring skills and tools for stripping, splicing, and connecting wires are required.

IMPORTANT

  • Do not submerge for long periods of time.
  • Do not power LED tape while coiled on reel, as the LEDs will overheat. The mounting surface will act as a heat sink to dissipate heat.
  • Do not stare directly into the LED lights when illuminated.
  • Never connect more than one power supply to a run of LED lighting.
  • Use only insulated staples and plastic clips to secure cords and wires.
  • Route and secure wires so they will not become pinched or damaged.
  • Do not install low-voltage DC wiring in the same runs as 120-volt AC power.
  • Do not submerge for long periods of time.
  • Do not power LED tape while coiled on reel, as the LEDs will overheat. The mounting surface will act as a heat sink to dissipate heat.
  • Do not stare directly into the LED lights when illuminated.
  • Never connect more than one power supply to a run of LED lighting.
  • Use only insulated staples and plastic clips to secure cords and wires.
  • Route and secure wires so they will not become pinched or damaged.
  •  Do not install low-voltage DC wiring in the same runs as 120-volt AC power.

All wiring must be in accordance with national and local electrical codes, low-voltage Class 2 circuit. If you are unclear as to how to install and wire this product, consult a qualified professional.

Planning
RibbonFlex LED lighting is designed for indirect lighting applications. The LEDs themselves are not intended to be seen directly by the eye. Every installation is unique, and the desired lighting effect is based primarily upon personal preference. Installation location, wall colors, mounting angles, and the light’s reflection off walls, surfaces, and objects will affect the final lighting appearance. Subtle adjustments to the positioning and angle of the LED tape can greatly impact the overall lighting effect.

Installation considerations

  •  How will you switch your LED lighting on and off?
  •  Do you want to be able to dim your lighting?
  •  What is the best layout configuration for your installation?
  •  What are the best ways to mount the tape lighting?
  •  How will you cut, connect, and conceal the wires to your lighting?

Powering LED tape light strips

Power tape light strips by wiring directly to a 12-volt battery. Maintain polarity at all connection points (+ to +, – to –).Armacost-631470
-RibbonFlex-Pro-18-Inch-Weatherproof-Red-Green-or-Blue-LED-Tape-Light-
FIG-1
A low-voltage LED dimmer can also be used with battery powered systems.
If connecting to a standard 120-volt circuit, a 12-volt DC power supply will be required.Armacost-631470-RibbonFlex-Pro-18-Inch-Weatherproof-Red-Green-
or-Blue-LED-Tape-Light-FIG-2

Surface preparation and installation
Before removing the 3M paper backing, test the LED strip in the space you intend to light. Once the platic backing is removed and the lighting is fully installed, you cannot reposition or move the LED tape light to another location. The tape may not stick securely.
Power the LED tape light and temporarily hold or tape into position with painter’s tape – do not remove the 3M plastic backing. Do not stare directly into the LEDs.
Try various angles and positions to get the desired level of illumination and lighting appearance. If the LEDs create undesirable bright spots on walls or reflections, reposition the tape light strip farther away from surfaces or try a different mounting angle.

  •  Mounting surfaces should be smooth, clean, completely dry, dust free and above 60ºF (15 ºC) before installing/sticking the LED tape strip in place. Thoroughly clean all mounting surfaces with isopropyl alcohol. Do not use common rubbing alcohol and household cleaners, which may leave behind residues.
  •  For best adhesion, lightly sand the surface where you will mount the tape lighting with fine grit sandpaper (150-300 grit). Sand in a circular motion rather than straight-line motion.
  •  When installing on painted surfaces, paint should be fully cured based on manufacturer’s cure time.
  •  Be careful not to peel off the 3M adhesive from LED strip; just remove the red plastic backing.
  •  3M sticky back tape requires pressure to activate the adhesive.
  • Working from one end to the other, firmly press the tape down with your fingers, taking care not to press on the individual LEDs.

Visit armacostlighting.com/installation for additional installation tips and FAQs.

  • Input voltage ……………………………………………………………… 12-volt DC
  • Energy consumption: Blue strips …………………………..4.14W (.35A) each Green & Red strips ………………..5.06W (.42A) each
  • Beam angle ………………………………………………………………………. 120°
  • LED light source …………………………………………. High Power SMD 2835
  • See product packaging or visit armacostlighting.com for additional product-specific information.

Three-year limited warranty

Improper installation, abuse, or failure to use this product for its intended purpose will void warranty. This warranty only applies when all components, including LED power supplies, have been provided by or approved for use by Armacost Lighting. The warranty does not cover labor or any other costs or expense to remove or install any defective, repaired or replaced products.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Armacost User Manuals

Related Manuals