magnum Pathfinder 500W Electric Bike User Manual
- June 6, 2024
- magnum
Table of Contents
Pathfinder 500W
PLEASE READ ME FIRST
www.magnumbikes.com
General Introduction
WELCOME
Thank you for purchasing a Magnum electric bike and welcome to the Magnum
Bikes family of e-bike enthusiasts. We encourage you to join our Facebook
group “Magnum Bikes Community” which you can find at the following link:
https://www.facebook.com/groups/389290978573773
Our Facebook group is a place for Magnum riders to ask questions, have
discussions, share recommendations and experiences and connect with other
Magnum Bike enthusiasts.
USE OF THE MANUAL
We encourage you to read this manual thoroughly before you take your new
E-bike for a ride. It is important not to overlook the safety instructions and
explanations of both traditional and non-traditional bike parts, as this will
offer you a general understanding of your new E-bike. This manual is designed
to help you get the most out of your E-bike, and so we have attempted to
answer as many of your potential questions as possible. Please take a moment
to read through the various sections before you get in the saddle.
SERVICE AND TECHNICAL SUPPORT
This manual is intended as a general overview of your new E-bike and is
therefore not an extensive reference. For technical support, including
information about service, maintenance and repairs, please consult your
dealer. You can visit our website
(www.magnumbikes.com) for more information about
our products and technology, or to find a dealer close to you.
INCLUDED WITH THE PATHFINDER E-BIKE
Unpacking & Assembling
STEP 1. Install the handlebar and stem
- Turn out the front end screw of the stem
- Open the front cover of the stem and put the handlebar into it. Adjust the angle of the handlebar
- Tighten the screw at the upper end of the stern and lock the handlebar
- After installation, move the handlebar back and forth to make sure the screws are tightened
STEP 2. Install pedals
- Take out the pedal and tool kit from the accessory box. L (left) and R (right) are engraved on the end of the foot screw.
- Screw-in the pedal, left counterclockwise, right clockwise, and finally, tighten with an open-end wrench.
Parts Introduction
1. Display
2. The left brake lever controls the rear disc brake
3. The right brake lever controls the front disc brake
4. Electronic horn| 5. Gear shifter
6. Throttle
7. Stem adjustment
---|---
Brake lever adjustment and fixing
Adjust the angle of the brake lever to a comfortable position, and then
tighten the screw above the brake lever with the Allen wrench from the
included tool kit.
HANDLEBAR HORIZONTAL ADJUSTMENT
When unpacking and assembling, adjust the horizontal angle of the handlebars
with stem adjustment 7. Adjust to a desired or comfortable horizontal
position and finally tighten the stem adjustment with provided tool kit.
Battery
BATTERY REMOVAL
Insert the key into the Inc–k hole on the Side of the e-bike and twist it
to the battery unlock position, then the battery can be taken out.
BATTERY INSTALLATION
Key is in the lock hole on the side of the battery in the unlock position,
then place the battery into the slot and twist the key to the lock position.
Remove key.
BATTERY SAFETY
Do not leave the battery unused for a long time, take it out and charge it
at least once a month. Battery failure caused by improper or irregular
charging is not covered by the warranty.
Try not to exhaust the battery completely during riding. Charge it as soon as
possible at the last bar of the battery indicator on the meter. Complete
exhaustion of the battery will affect the battery life.
Waterproof instructions: The battery casing protects from basic rain while
inserted and riding. Do not leave the whole e-bike in rain for a long time.
After exposure to light rain wipe the battery dry as soon as possible.
DO NOT submerge the battery or allow heavy rain exposure.
Product Specs
ELECTRONIC DETAILS
Motor Type: Rear Geared Hub Motor
Motor Output:48v 500w
Battery Voltage / Amp Hours / Watt Hours: 48v / 13ah /624wh
Battery Chemistry: Lithium Nickel Cobalt Manganese (Li-ncm)
Estimated Charge Time: 4-4.5 Hrs
Estimated Min And Max Range:30 To 50 Miles (Depending On Riding Style,
Terrain, Rider Weight, and Pedal Assist Level.)
Display Type: Bigstone H102 Display
Display Readouts: Speed (mph or kph), Frontlight on/off, Assist Level 0-3,
Battery Level, Odometer, Trip Distance, Range (estimated remaining mileage)
Drive Modes: Pedal Assist, Twist Throttle
Max Speed:25mph
Lights: Integrated Front and Rear Light controlled by the display (power
on/off)
BICYCLE DETAILS
Total Weight: 50Ibs
Battery Weight: Bibs
Frame Type: Low Step
Fork Details: Fixed Alloy
Gearing Details: Shimano Altus 7 Speed
Shifter Details: Shimano Altus
Stem: Adjustable Alloy
Brake Details: Tektro Hydraulic disc brakes
Saddle: VELO saddle
Seat post:Rigid
Rack / Fenders: Rear rack, front and rear fenders
Tires: Innova 20″ fat tire
Wheel Size:20″ x 3″
Safety
PRECAUTIONS
- When adjusting the handlebars or saddles, be careful not to expose the safety line marks off the handlebars and saddles
- Before cleaning the e-bike, please turn off the main power supply and unplug the charging cable
- Note about water washing: It is strictly forbidden to directly wash or soak the e-bike with a high-pressure water gun or water pipe, and it is strictly forbidden to wash with water
- This product has a certain rain-proof function, please dry it in time after riding on rainy days, do not rain for a long time
BATTERY CHARGING & MAINTENANCE
- Charge at 0°C – 40°C, discharge at -20°C – 50°C, keep the battery dry and ventilated
- When there is only one battery power indicator or the meter shows only one bar left, please turn off the power and charge it in time. The exhaustion of the battery will seriously affect the battery’s performance and life. Please turn off the electric door lock when charging
- Do not leave your battery charging overnight.
- Please use the original charger, pay attention to the battery type and voltage applied to the charger
- The charger lights up in red during charging and turns green when fully charged. Please unplug the charging head when the battery is full.
- Please close the rubber cover of the charging port after charging, otherwise, it will affect the rainproof effect and cause damage to the battery
- When replacing the charger, it should match the battery model
- It is strictly forbidden to put the battery in acid or alkaline liquid, try to avoid rain, keep away from fire, heat, and high temperature. It is strictly forbidden to destroy or disassemble the battery. Do not insert metal objects into the charging port to avoid short circuits.
- Used batteries cannot be dismantled without authorization, and should be recycled by relevant professional departments
Pathfinder Display Manual
Specification of H102 Display
Key Functions
H102 display is included 3 buttons, the distribution position is shown in the
figure below, and the functions are as follows
Power key, for switching machine and function confirmation, and information
switching function.
Adjust and increase the button, which is used to adjust the power gear, select
the setting options and switch the lights.
Adjust and reduce buttons for power gear adjustment, setting options
selection, and 6KM start assistant.
Functional Overview
6.1. Switch on and off machine operation and display
Shut downstate, continue to press down 2 seconds The meter displays the
welcome form and then enters the main form of the system.
In the power-on state, press continuously 2 seconds, the meter displays the
shutdown form, and then the system shutdown. The button can be released.
6.2. Main form and operation
H102 provides you with a variety of displays to meet your riding needs. The
display content of H102 includes
-
Speed display :
Shows the speed of the current ride. -
Speed unit display:
You can set the select speed unit by km/h or mph. -
6KM Display:
When the power gear is not 0Continuous press for opening the 6km implementation functions location will display the 6km icon. -
The lights display:
Power On mode holds the key for more than 2 seconds, for opening or turning off the lights. -
assistant level displays:
Display the current assistant level, turn on the default level 0, adjustable range 0-6, and the 6th level may be hidden, but can be hidden or closed by setting items. -
Battery level display:
Display current battery power information. The battery is full of electricity, showing full, and when the last level starts flashing, the tip needs to be charged to the battery. -
Bluetooth instructions:
Bluetooth function not available on the Pathfinder 350 or 500 -
Information display:
i. ODO: This shows the mileage accumulated by the user.
ii. TRIP: Display the user’s cycling mileage. The single mileage will not
be cleared when power is off. The user needs to reset the mileage manually in
the setting interface.
iii. RANGE: Remaining mileage. The remaining mileage is an estimate that
may differ from the actual ride.
6.3. Average speed and maximum speed display
Under the normal speed display interface, press the key and the key at the
same time to enter the average speed and maximum speed display page, as shown
below
Average speed refers to the average speed of the vehicle up to the moment of
starting up, and the maximum speed is also the maximum speed recorded so far
in this starting up. After shutdown and restart, the average speed and maximum
speed start recording and calculation again.
Press any key once to exit the average speed and maximum speed display.
6.4. Setting item description and operation
6.4.1. Enter and exit the Settings page and instructions for the
Settings
Press the key and at the same time enter the setting interface. The meter on
the setting page is displayed as follows:
On the Settings page, you can select and modify or display the items.
After the item is selected, press the key to confirm the perforation
If more than one page is displayed, there will be PAGE DOWN under the display
area. Select PAGE DOWN to enter the next page.
In the Settings page, press and at the same time can quickly exit the Settings
page, back to the main page display.
Wheel setting and display
Select the TIRE SIZE, and then press the key to enter the Wheel
Diameter Setting and Display Items page.
If the vehicle controller has fixed the vehicle wheel diameter size, this
numeric term will not be adjustable and will only be used to display the
system wheel diameter size.
6.4.2. Unit settings and display
Select the UNITS, and then press the key to enter the Unit Settings and
Display Items page.
Users can adjust the display unit of mileage and speed according to actual
needs. Choice of metric or British units.
6.4.3. Maximum speed setting
Select the TOP SPEED, and then press the key to enter the Maximum Speed
Setting page.
This item can be adjusted only by entering the password, which can be selected
as 20KM/H, 25HK/H, and 32KM/H. Please consult the dealer or vehicle
manufacturer for the password.
6.4.4. Battery information.
Select the BATTERY INFO and then press the key to enter the
BATTERY information display page.
Display current battery voltage, battery capacity, number of charging cycles.
If the battery is not recommended by the manufacturer, the battery information
may not be displayed properly.
6.4.5. System version
Select the VERSION, and then press the key to enter the Version information
display page.
Display the hardware version and the software version, respectively.
6.4.6. Hidden assistant level setting
Select the PAGE DOWN, and then press the key to enter the next
Settings page, select HIDE LEVEL and then press again.
Select ON to turn on the hidden gear function, and select OFF to turn off the
hidden gear function. If ON is selected, the adjustable range of the gear in
the main interface is 0-5. If OFF is selected, the adjustable range of the
power gear is 0-6.
6.4.7. Mode setting
Select the MODE, and then press the key to enter the Mode setting item.
SPEED mode or TORQUE mode can be selected depending on the type of power
sensor. Default SPEED mode.
6.4.8. Single mileage reset
Select the TRIP, and then press the key to enter the TRIP page.
Press the key and at the same time for more than 2 seconds to clear the single mileage value.
Common questions and solutions
Q: Why can’t you turn it on?
Answer: the boot needs to hold down the power button for 2 seconds. If
you can’t turn on the check table wire beam and the controller’s connector
contact is secure.
Q: How should the instrument display the fault code?
A: Please check the corresponding faults according to the fault
description and control check. If you can’t solve it, please send the vehicle
to the nearest dealer.
Q: the operating instrument has no response and how to handle it.
Answer: Long presses the power key for more than 2 seconds, turns on
again.
Warranty
Your MAGNUM E-bike comes with a limited warranty. Please visit
www.maanumbikes.com or your local magnum dealer
for details.
The bike must be registered at
www.magnumbikes.com/warranty in order
to be covered by the one-year warranty.
Stay Connected
@magnumbikes
@magnumbikes
www.magnumbikes.com
info@magnumbikes.com
323-375-2666
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>