ROTEL RA‑1592MKII Stereo Integrated Amplifier Owner’s Manual
- June 6, 2024
- ROTEL
Table of Contents
RA‑1592MKII Stereo Integrated Amplifier
Owner’s Manual Manuel de l’utilisateur Bedienungsanleitung Manual de Instrucciones Gebruikershandleiding Manuale di istruzioni Instruktionsbok
A
B
RA1592MKII
Stereo Integrated Amplifier Amplificateur Stéréo Intégré StereoVollverstärker
Amplificador Integrado Estereofónico Geïntegreerde stereoversterker
Amplificatore integrato stereo Integrerad stereoförstärkare
2
RA1592MKII Stereo Integrated Amplifier
Important Safety Instructions
Notice
The RS232 connection should be handled by authorized persons only.
WARNING: There are no user serviceable parts inside. Refer all servicing to
qualified service personnel.
WARNING: To reduce the risk of fire or electric shock, do not expose the unit
to moisture or water. Do not expose the unit to dripping or splashing. Do not
place objects filled with liquids, such as vases, on the unit. Do not allow
foreign objects to get into the enclosure. If the unit is exposed to moisture,
or a foreign object gets into the enclosure, immediately disconnect the power
cord from the wall. Take the unit to a qualified service person for inspection
and necessary repairs.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade or the third
prong are provided for your safety. If the provided plug does not fit into
your outlet, consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/ apparatus combination to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when unused for long periods
of time.
Refer all servicing to qualified service personnel. Servicing is required when
the apparatus has been damaged in any way, such as power supply cord or plug
is damaged, liquid has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate normally,
or has been dropped.
The apparatus should be used in non tropical climate.
The ventilation should not be impeded by covering the ventilation openings
with items, such as newspapers, table-cloths, curtains, etc.
No naked flame sources, such as lighted candles, should be placed on the
apparatus.
Touching uninsulated terminals or wiring may result in an unpleasant
sensation.
You must allow a minimum 10 cm or 4 inches of unobstructed clearance around the unit.
A
B
WARNING: The rear panel power cord connector is the mains power disconnect
device. The device must be located in an open area that allows access to the
cord connector.
The unit must be connected to a power supply only of the type and voltage
specified on the rear panel. (USA: 120 V/60Hz, EC: 230V/50Hz)
Connect the component to the power outlet only with the supplied power supply
cable or an exact equivalent. Do not modify the supplied cable. Do not use
extension cords.
The mains plug is the disconnect of the unit. In order to completely
disconnect the unit from the supply mains, remove the main plug from the unit
and the AC power outlet. This is the only way to completely remove mains power
from the unit.
Use Class 2 wiring for speaker connections to ensure proper installation and
minimize the risk of electrical shock.
The batteries in the remote control should not be exposed to excessive
temperature such as sunshine, fire or other heat sources. Batteries should be
recycled or disposed as per state and local guidelines.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following to conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Rotel products are designed to comply with international directives on the Restriction of Hazardous Substances (RoHS) in electrical and electronic equipment and the disposal of Waste Electrical and Electronic Equipment (WEEE). The crossed wheelie bin symbol indicates compliance and that the products must be appropriately recycled or processed in accordance with these directives.
This symbol means that this unit is double insulated. An earth connection is not required.
1
2
3
Pin Assignments
Balanced Audio (3 pole XLR): Pin 1: Ground / Screen Pin 2: In phase / +ve /
Hot Pin 3: Out of phase / ve / Cold
Figure 1: Controls and Connections Commandes et Branchements Bedienelemente und Anschlüsse Controles y Conexiones Bedieningselementen en aansluitingen C ontrolli e connessioni Kontroller och anslutningar
1
2
3
3
4
A
B
56
7 0
8
9
–
=q w e r t
y
ui o ] p [
4
Figure 2: RRAX150 Remote Control Télécommande infrarouge RRAX150 Fernbedienung
RRAX150 Mando a Distancia RRAX150
RA1592MKII Stereo Integrated Amplifier
Afstandsbediening RRAX150 Telecomando RRAX150 RRAX150 fjärrkontroll RR-AX150
A
K
SPKR A SPKR B
B
C
D L
E
M
F
MENU
G
N
H
I
J
RR-AX150
5
Figure 3: Analog Input and Speaker Output Connections Branchements des entrées analogiques et sorties enceintes acoustiques Anschlussdiagramm (analoge Eingangsanschlüsse, Ausgangsanschlüsse für die Lautsprecher) Conexiones de Entrada Analógicas y de Salida a las Cajas Acústicas Analoge ingangen en luidsprekeruitgangen Collegamenti ingressi analogici ed uscite diffusori Anslutningar för högtalare och analoga ingångar
Rotel RA-1592MKII
GND R
L
CLASS 1 LASER PRODUCT APPAREIL LASER
DE CLASSE 1
SPEAKER
PHONO
Rotel RCD-1572
RP-565E
SPEAKER
6
Figure 4: Digital Input and 12 Volt Trigger Out Connections Entrées numériques
et Branchements des sorties trigger 12 V Anschlussdiagramm (Digitaleingänge,
12VTriggerAusgänge) Entrada Digital y Conexiones de Salida para Señal de
Disparo de 12 Voltios Digitale ingangen en 12Vtriggeruitgangen Collegamenti
ingressi digitali e segnali Trigger 12 V Anslutningar för digitala ingångar
och 12volts styrsignaler 12-
RA1592MKII Stereo Integrated Amplifier
CD PLAYER
DIGITAL AUDIO OUTPUT OPTICAL COAXIAL
Computer (Supplied)
Rotel RA-1592MKII
CLASS 1 LASER PRODUCT APPAREIL LASER
DE CLASSE 1
Rotel RCD-1572
RP-565E
7
Figure 5: Balanced (XLR) Inputs Entrées symétriques (XLR) Anschlussdiagramm (symmetrische (XLR) Eingänge) Entradas Balanceadas (XLR)
Gebalanceerde ingangen (XLR) Collegamenti ingressi bilanciati (XLR)
Balanserade anslutningar (XLR)
(XLR)
Rotel RA-1592MKII
CLASS 1 LASER PRODUCT APPAREIL LASER
DE CLASSE 1
Rotel RCD-1572
RP-565E
8
RA1592MKII Stereo Integrated Amplifier
Important Notes
When making connections be sure to: 4 Turn off all the components in the
system before hooking up any components, including loudspeakers. 4 Turn off
all components in the system before changing any of the connections to the
system. It is also recommended that you: 4 Turn the volume control of the
amplifier all the way down before the amplifier is turned on or off.
Remarques importantes
Pendant les branchements, assurez-vous que : 4 Tous les maillons sont éteints
avant leur branchement, quels qu’ils soient, y compris les enceintes
acoustiques. 4 Éteignez tous les maillons avant de modifier quoi que ce soit
au niveau de leurs branchements, quels qu’ils soient. Il est également
recommandé de : 4 Toujours baissez le niveau sonore via le contrôle de volume,
avant d’allumer ou d’éteindre l’amplificateur.
Wichtige Hinweise
Achten Sie beim Herstellen der Verbindungen auf Folgendes: 4 Schalten Sie alle
Komponenten im System ab, bevor Sie Geräte (einschließlich Lautsprecher)
anschließen. 4 Schalten Sie alle Komponenten im System ab, bevor Sie
Anschlüsse im System verändern. Ferner empfehlen wir, dass 4 Sie die
Lautstärke herunterdrehen, bevor Sie den Verstärker ein- oder abschalten.
Notas Importantes
Cuando realice las conexiones, asegúrese de que: 4 Desactiva todos los
componentes del equipo, cajas acústicas incluidas, antes de conectar cualquier
nuevo componente en el mismo. 4 Desactiva todos los componentes del equipo
antes de cambiar cualquier conexión del mismo. También le recomendamos que: 4
Reduzca el nivel de volumen de su amplificador a cero antes de activarlo o
desactivarlo.
Héél belangrijk
Bij het maken van de verbindingen: 4 Zorg dat niet alleen de RA-1592MKII, maar
de gehele installatie uitstaat, als nog niet alle verbindingen gemaakt zijn. 4
Zorg dat niet alleen de RA-1592MKII, maar de gehele installatie ook uitstaat,
als u verbindingen gaat wijzigen. Wij raden u ook aan om 4 de volumeregelaar
van de (voor)versterker geheel dicht te draaien (volkomen linksom) wanneer u
uw eindversterker aan- of uitzet.
Note importanti
Quando effettuate i collegamenti assicuratevi di: 4 Spegnere tutti i
componenti del sistema prima di collegare qualsiasi componente, inclusi i
diffusori. 4 Spegnere tutti i componenti del sistema prima di modificare
qualsiasi connessione nel sistema. Vi raccomandiamo inoltre di: 4 Portare il
volume a zero prima di accendere o spegnere l’amplificatore.
Viktigt
Tänk på följande när du gör anslutningar: 4 Stäng av alla apparater i
anläggningen innan du ansluter nya komponenter eller högtalare. 4 Stäng av
alla apparater i anläggningen innan du ändrar någon anslutning. Du
rekommenderas också: 4 Vrida ner volymen på förförstärkaren helt och hållet
innan förstärkaren slås på eller av.
ÇÊÌ°Â ÁÏÂ~ÌËfl
è ÔÓÒÓÂËÌÂÌËÂÏ: 4 Ç°ÍÎ~ËÚ ,Ò ÍÓÏÔÓÌÂÌÚ°, ,ÍÎ~fl ÍÓÎÓÌÍË. 4 Ç°ÍÎ~ËÚ ,ÒÂ
ÍÓÏÔÓÌÂÌÚ° , ,¯ÂÈ ÒËÒÚÂÏÂ, ÔÂÊ ~ÂÏ ~ÚÓ-ÚÓ , ÌÂÈ ÏÂÌflÚ¸. êÂÍÓÏÂÌÛÂÚÒfl ÚÍÊÂ:
4 Ç°,ÂÒÚË ,,ÓÏÍÓÒÚ¸ ÛÒËÎËÚÂÎfl Ì ÏËÌËÏÛÏ, ÔÂÂ ÚÂÏ ÍÍ ,ÍÎ~Ú¸ ËÎË ,°ÍÎ~Ú¸ Â,,Ó.
9
Contents
About Rotel
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Figure 1: Controls and Connections
3
Figure 2: RRAX150 Remote Control
4
Figure 3: Analog Inputs and Speaker Output Connections
5
Figure 4: Digital Input and 12 Volt Trigger out Connections
6
Figure 5: Balanced (XLR) Inputs
7
Important notes
8
About Rotel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
A Word About Watts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
A Few Precautions
10
Placement
10
Cables
10
The RRAX150 Remote Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Remote Control Batteries
10
AC Power and Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
AC Power Input [
10
POWER Switch and Power Indicator 1
11
12V TRIGGER Connection r
11
Input Signal Connections -up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Phono Input u and Ground Connection (GND)
11
Line Level Inputs u
11
Balanced (XLR) Inputs p
11
Digital Signal Inputs –
11
Output Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
MONO SUB Output i
11
Preamp Output o
11
Headphone Output 5
11
Speaker Outputs ] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Speaker Selection
11
Speaker Wire Selection
11
Polarity and Phasing
12
Speaker Connections ]
12
Remote Sensor 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Display 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Front USB Input 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
APTX Bluetooth Connection 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Audio Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
VOLUME Control 4D
12
BALANCE Control 9C
12
TONE Control Bypass 9C
12
BASS and TREBLE Controls 9C
12
Source Input Selector 8J
13
Dimmer Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Display Dimmer 9B
13
PCUSB Input q . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
RS232 t . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Rotel Link w . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
EXT REM IN Jack e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Network Connection = . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Protection Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Settings Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Power Indicator Is Not Illuminated
15
Fuse Replacement
15
No Sound
15
Cannot Connect via Bluetooth
16
Playable Audio Formats
16
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Our story began over 50 years ago. Over the decades, we have received hundreds
of awards for our products and satisfied hundreds of thousands of people who
take their entertainment seriously – like you!
Rotel was founded by a family whose passionate interest in music led them to
manufacture high-fidelity components of uncompromising quality. Through the
years, that passion has remained undiminished and the family goal of providing
exceptional value for audiophiles and music lovers, regardless of their
budget, is shared by all Rotel employees.
Rotel’s engineers work as a close team, listening to, and fine tuning, each
new product until it reaches their exacting musical standards. They are free
to choose components from around the world in order to make that product the
best they can. You are likely to find capacitors from the United Kingdom and
Germany, semiconductors from Japan or the United States, while toroidal power
transformers are manufactured in Rotel’s own factory.
We all have concerns about our environment. And, as more and more electronics
are produced it is especially important for a manufacturer to do all it can to
engineer products that have a minimum impact on the environment.
At Rotel, we are proud to do our part. We have reduced the lead content in our
products by using special lead-free ROHS solder and components. Our engineers
continually strive to improve power supply efficiency without compromise to
quality. When in standby mode Rotel products use minimal power to meet global
Standby Power Consumption requirements.
The Rotel factory is also doing their part to help the environment through
constant improvements to product assembly methods for a cleaner and greener
manufacturing processes.
All of us at Rotel thank you for buying this product. We are sure it will
bring you many years of enjoyment.
A Word About Watts
This amplifier’s power output is rated as 200 watts for each channel, when
both channels are operating together at full power. Rotel has chosen to
specify the power output in this way because, in Rotel’s experience, it gives
the truest value of the receiver or amplifier’s power capability.
When comparing specifications for different products, you should be aware that
power output is often specified in other ways, so you may not be comparing
like with like. For example, the power output may be quoted with only one
channel operating, giving a higher maximum figure.
A loudspeaker’s impedance rating indicates the electrical resistance or load
it offers when connected to the amplifier, usually 8 ohms or 4 ohms. The lower
the impedance, the more power the speaker will need. In effect, a 4 ohm
speaker will require twice as much power as an 8 ohm speaker.
However, Rotel amplifiers are designed to work into any speaker impedance
between 8 and 4 ohms, and with all the channels working up to their full
power. Because Rotel designs are optimized for use with all channels operating
together, Rotel is able to specify the true power output for both channels.
10
RA1592MKII Stereo Integrated Amplifier
Getting Started
Thank you for purchasing the Rotel RA-1592MKII Stereo Integrated Amplifier.
When used in a high-quality music audio system, your Rotel product will
provide years of musical enjoyment.
The RA-1592MKII is a full featured, high performance component. All aspects of
the design have been optimized to retain the full dynamic range and subtle
nuances of your music. The RA-1592MKII has a highly regulated power supply
incorporating a Rotel custom-designed toroidal power transformer and custom-
made slit foil capacitors. This low impedance power supply has ample power
reserves, which enables the RA-1592MKII to easily reproduce the most demanding
audio signals. This type of design is more expensive to manufacture, but it is
better for the music.
The printed circuit boards (PCB) are designed with Symmetrical Circuit Traces.
This insures that the precise timing of the music is maintained and faithfully
recreated. The RA-1592MKII circuitry uses metal film resistors and polystyrene
or polypropylene capacitors in important signal paths. All aspects of this
design have been examined to ensure the most faithful music reproduction.
The main functions of the RA-1592MKII are easy to install and use. If you have
experience with other stereo systems, you shouldn’t find anything perplexing.
Simply plug in the associated components and enjoy.
A Few Precautions
WARNING: To avoid potential damage to your system, turn off ALL the components
in the system when connecting or disconnecting the loudspeakers or any
associated components. Do not turn the system components back on until you are
sure all the connections are correct and secure. Pay particular attention to
the speaker wires. There must be no loose strands that could contact the other
speaker wires, or the chassis of the amplifier.
Please read this manual carefully. In addition to basic installation and
operating instructions, it provides valuable information on various RA-1592
system configurations as well as general information that will help you get
optimum performance from your system. Please contact your authorized Rotel
dealer for answers to any questions you might have. In addition, all of us at
Rotel welcome your questions and comments.
Save the shipping carton and all enclosed packing material for future use.
Shipping or moving the RA-1592MKII in anything other than the original packing
material may result in severe damage to your amplifier.
If included in the box please complete the owner’s registration card or
register on line. Also be sure to keep the original sales receipt. It is your
best record of the date of purchase, which you will need in the event warranty
service is ever required.
Placement
Like all audio components that handle low-level signals, the RA-1592MKII can
be affected by its environment. Avoid placing the RA-1592MKII on top of other
components. Also avoid routing audio signal cables near power cords. This will
minimize the chance it will pick up hum or interference.
The RA-1592MKII generates heat as part of its normal operation. The heat sinks
and ventilation openings in the amplifier are designed to dissipate this heat.
The ventilation slots in the top cover must be open. There should be
10 cm (4 inches) of clearance around the chassis, and reasonable airflow
through the installation location, to prevent the amplifier from overheating.
Remember the weight of the amplifier when you select an installation location.
Make sure that the shelf or cabinet can support it. We recommend installing
the RA-1592MKII in furniture designed to house audio components. Such
furniture is designed to reduce or suppress vibration which can adversely
affect sound quality. Ask your authorized Rotel dealer for advice about
component furniture and proper installation of audio components.
The RA-1592MKII is supplied with an RR-AX150 remote control and must be placed
where the infrared signal from the remote can reach the front panel Remote
Sensor.
Cables
Be sure to keep the power cords, digital signal cables and analog audio signal
cables in your installation away from each other. This will minimize the
chance of the analog audio signal cables picking up noise or interference from
the power cords or digital cables. Using only high quality, shielded cables
will also help to prevent noise or interference from degrading the sound
quality of your system. If you have any questions see your authorized Rotel
dealer for advice about the best cable to use with your system.
The RRAX150 Remote Control
Some functions can be done with either the front panel controls, or the
supplied RR-AX150 remote control. When these operations are described, the
square call out numbers refer to the main unit, while the encircled letters
refer to the remote control.
Remote Control Batteries
Two AA size batteries (supplied) must be installed before the remote control
can be used. To install the batteries, remove the cover on the back of the RR-
AX150. Install the batteries as shown in the illustration in the battery well.
Test the control for proper operation, then replace the cover. When the
batteries become weak the remote control won’t operate the RA-1592MKII
consistently. Installing fresh batteries should eliminate the problem.
AC Power and Control
AC Power Input [
Your RA-1592MKII is configured at the factory for the proper AC line voltage
in the country where you purchased it (either 120 volts AC or 230 volts AC
with a line frequency of either 50 Hz or 60 Hz). The AC line configuration is
noted on a decal on the back panel.
NOTE: Should you move your RA1592MKII to another country, it is possible to
reconfigure your amplifier for use on a different line voltage. Do not attempt
to perform this conversion yourself. Opening the enclosure of the RA1592MKII
exposes you to dangerous voltages. Consult a qualified service person or the
Rotel factory service department for information.
NOTE: Some products are intended for sale in more than one country and as such
are supplied with more than one AC cord. Please only use the one appropriate
for your country/region.
Because of its relatively high power rating, the RA-1592MKII can draw
considerable current. Therefore, it should be plugged directly into a 2-pin
11
polarized wall outlet. Do not use an extension cord. A heavy duty multi-tap
power outlet strip may be used if it (and the wall outlet) is rated to handle
the current demanded by the RA-1592MKII and all the other components connected
to it.
If you are going to be away from home for an extended period of time such as a
month-long vacation, it is a sensible precaution to unplug your amplifier (as
well as other audio and video components) while you are away.
POWER Switch and Power Indicator 1
Press the front panel Power Switch button, to turn the unit on. The Power
Indicator light is illuminated when the unit is on. Press Power Switch button
again to turn the unit off.
When the power switch is in the ON position, the remote control ON and OFF
buttons may be used to activate the RA-1592MKII. In Standby mode the power LED
remains lit, but the display is turned off.
NOTE: Place the self adhesive ring over the light surrounding the Power switch
if the blue light is too bright.
12V TRIGGER Connection r
See Figure 4 Some audio components can be turned on automatically when they
receive a 12V turn on signal. The two 12V Trigger Outputs of the RA-1592MKII
provide the required signal. Connect compatible components to the RA-1592MKII
with a conventional 3.5mm mini plug cable. When the RA-1592MKII is in turn off
mode, the trigger signal is interrupted, so the components controlled by it
are turned off.
Input Signal Connections
NOTE: To prevent loud noises that neither you nor your speakers will
appreciate, make sure the system is turned off when you make any signal
connections.
Phono Input u and Ground Connection (GND)
See Figure 3 Plug the cable from the turntable into the appropriate left and
right phono inputs. If the turntable has a “ground” wire, connect it to the
screw terminal to the left of the Phono inputs. It will help prevent hum and
noise.
Line Level Inputs u
See Figure 3 The CD, Tuner, and Aux inputs of the amplifier are analog “line
level” inputs. These inputs are for connecting components such as CD players
or other audio playback devices with an analog audio output.
The left and right channels are clearly labeled and should be connected to the
corresponding channels of the source component. The Left connectors are white,
the Right connectors are red. Use high quality RCA cables for connecting input
source components to the RA-1592MKII. Ask your authorized Rotel dealer for
advice about cables.
Balanced (XLR) Inputs p
See Figure 5 A pair of balanced XLR inputs accept audio signals from CD
player, Blu-ray player or other source components with XLR outputs.
NOTE: You should choose only one method of analog connection from a source
component to RA1592MKII. Do not connect both the RCA and XLR outputs of a
source component to the RA1592MKII at the same time.
Digital Signal Inputs –
See Figure 4 There are three sets of digital inputs labeled 1, 2 and 3, for
COAXIAL and OPTICAL respectively. Connect the COAXIAL or OPTICAL PCM outputs
of your source component into these sockets. The digital signals will be
decoded and played by the RA-1592MKII. The unit is capable of decoding PCM
signals up to 24 bit, 192kHz.
Output Connections
MONO SUB Output i
There are 2 connectors for mono subwoofer output to connect to a subwoofer.
These mono outputs are summed with both the left and right audio signal. They
are parallel outputs allowing 2 subwoofers to be connected to the RA-1592MKII.
Preamp Output o
The RA-1592MKII has a set of preamp outputs labeled PRE OUT. The currently
selected source input is available from this output. Typically the PRE OUT
output is used to provide a signal to another integrated amplifier or power
amplifier, which is used to drive remote speakers.
NOTE: Changes to the settings of the Volume, Balance or Tone controls affect
the signal from the Preamp Output.
Headphone Output 5
The headphone output allows you to connect headphones for private listening.
This output accepts a standard 3.5mm (1/8″) mini stereo headphone connector.
Plugging in a set of headphones does not cut off the signal to
the speakers. Use the front panel 7 or remote control K A-B Speaker
Selector to turn off the speakers.
NOTE: Because the sensitivity of speakers and headphones can vary widely,
always reduce the volume level before connecting or disconnecting headphones.
Speaker Outputs ] See Figure 3
The RA-1592MKII has two sets of speaker outputs, labeled SPEAKER A and SPEAKER
B. The speaker outputs are controlled by the A-B speaker selector
buttons 7 on the front panel and the buttons K on the remote control.
Speaker Selection
If only one set of speakers will be used at any given time, the speakers may
have an impedance as low as 4 ohms. If there are times when both the A and B
speakers will be used, all the speakers should have an impedance of 8 ohms or
more. Speaker impedance ratings are less than precise. In practice, very few
loudspeakers will present any problems for the RA-1592MKII. See your
authorized Rotel dealer if you have any questions.
Speaker Wire Selection
Use insulated two-conductor stranded wire to connect the RA-1592MKII to the
speakers. The size and quality of the wire can have an audible effect
12
RA1592MKII Stereo Integrated Amplifier
on the performance of the system. Standard speaker wire will work, but can
result in lower output or diminished bass response, particularly over longer
distances. In general, heavier wire will improve the sound. For best
performance, you may want to consider special high-quality speaker cables.
Your authorized Rotel dealer can help in the selection of cables for your
system.
Polarity and Phasing
The polarity the positive/negative orientation of the connections for
every speaker and amplifier connection must be consistent so all the speakers
will be in phase. If the polarity of one connection is reversed, bass output
will be very weak and stereo imaging degraded. All wire is marked so you can
identify the two conductors. There may be ribs or a stripe on the insulation
of one conductor. The wire may have clear insulation with different color
conductors (copper and silver). There may be polarity indications printed on
the insulation. Identify the positive and negative conductors and be
consistent with every speaker and amplifier connection.
Speaker Connections ] Turn off all the components in the system before
connecting the speakers. The RA-1592MKII has color-coded binding post type
speaker connectors on the back panel. These connectors accept bare wire,
connector lugs, or dual banana type connectors. (except in European Community
countries where their use is not permitted.)
Route the wire from the RA-1592MKII to the speakers. Give yourself enough
slack so you can move the components to allow access to the speaker
connectors.
If you are using dual banana plugs, connect them to the wires and then plug
into the backs of the binding posts. The thumbscrews of the binding posts
should be screwed in all the way (clockwise).
If you are using terminal lugs, connect them to the wires. If you are
attaching bare wires directly to the binding posts, separate the wire
conductors and strip the insulation from the end of each conductor. Be careful
not to cut into the wire strands. Unscrew (turn counterclockwise) the binding
post. Place the connector lug or wire around the binding post shaft. Turn the
binding post clockwise to clamp the connector lug or wire firmly in place.
NOTE: Be sure there are no loose wire strands that could touch adjacent wires
or connectors.
Remote Sensor 2
This remote sensor window receives IR commands from the remote control. Please
do not block this sensor.
Display 3
The front panel display shows the source selected, volume level and tone
settings. The display provides access to the setup and configuration menu
options of the amplifier.
Front USB Input 6
The front USB input can be connected to an iPhone, iPad or iPod device
providing music playback to the amplifier. To enable audio playback using
one of these devices simply plug the device into the front USB and select USB
as the desired source. The iPhone, iPad and iPod device will remain active
allowing search and play functions.
APTX Bluetooth Connection 0
The Bluetooth Antenna 0 on the RA-1592MKII’s back panel is for wireless
streaming via Bluetooth, from your device (i.e. mobile phones, tablets or
computers). From your device, look for “Rotel Bluetooth” and connect to it.
Connection is normally automatic, but if prompted for a password, please press
“0000” on your device. The RA-1592MKII’s supports both traditional Bluetooth,
AAC and APTX Bluetooth audio streaming.
Audio Controls
VOLUME Control 4D
Turn the knob clockwise to increase the volume, or counter clockwise to
decrease the volume. From the remote control press the volume + or – button
to turn the volume up or down. Press the MUTE E button to completely
mute the volume.
BALANCE Control 9C
The Balance Control adjusts the left-to-right balance of the sound output. The
factory default is the center position or “0”. To change the balance from
the front panel, press the MENU 9 button to toggle the front display to
BALANCE SETTING mode. Then press the – or + buttons on the front panel to
change the value to LEFT or RIGHT. The value can change from L15 to R15.
NOTE: This setting is saved permanently including after powering off the
RA1592MKII.
To make temporary changes not saved after power off, from the remote,
press the BAL C button to access the BALANCE SETTING menu, then press the
up/down/left/right G arrow buttons to adjust. When finished, press the BAL C
button again to exit the menu.
Tone Control Bypass 9C
Bass and Treble Control (Tone Control) circuits are bypassed at factory
default to ensure the purest possible sound. The front display will show TONE
BYPASS. To turn on the tone control from the front panel, press the MENU
9 button to toggle to the Bypass control then press the – or + buttons on
the front panel to turn bypass on or off.
NOTE: This setting is saved permanently including after powering off the
RA1592MKII.
To temporarily changes the Tone Control Bypass, press the BYPASS C button
on the remote control to toggle the Bypass mode enabled and disabled.
Bass and Treble Controls 9C
Set the Bass or Treble controls from the front panel by pressing the MENU
9 button to toggle to the BASS / TREBLE menu. Press ENTER 9 button to toggle
between the options. Press the – or + 9 button to adjust the value.
The Bass and Treble values range from -10 to +10.
NOTE: These settings are saved permanently including after powering off the
RA1592MKII.
13
To temporarily change the Bass and Treble settings from the remote control,
press the BASS or TREB button C, then press the up/down/left/right G
arrow buttons on the remote to adjust the value.
NOTE: Bass and Treble changes are only available when Tone Bypass is disabled
(see Tone Control Bypass section).
A properly setup high-performance audio system produces the most natural sound
with little or no adjustment of the tone controls. Use these controls
sparingly. Be particularly careful when turning the controls up as this
increases the power output in the bass or treble range, increasing the load on
the amplifier and speakers.
NOTE: Setting the Bass and Treble controls does not automatically turn on the
tone control. To turn on tone control, refer to previous section Tone Control
Bypass.
Source Input Selector 8J
Press the corresponding input button on the front panel 8 or remote control J
to select the desired listening source.
Push the front panel source buttons to toggle between Optical 1 – 3, Coaxial
1- 3 and Aux or use the dedicated source button on the remote control.
Dimmer Control
Display Dimmer 9B To change the brightness of the front display, press the
MENU 9 button
to toggle to the Display Settings. Then press the – or + buttons on the front
panel to change the brightness.
NOTE: This setting is saved permanently including after powering off the
RA1592MKII.
To temporarily change the display brightness, press the DIM B button on
the remote.
PCUSB Input q
See Figure 4
Connect this input using the supplied USB cable to the USB socket of your
computer.
The RA-1592MKII supports both USB Audio Class 1.0 and USB Audio Class 2.0
modes. Windows computers do not require installation of a driver for USB Audio
Class 1.0 and support playback of audio up to 96kHz sampling rates. The
Factory Default setting is USB Audio Class 1.0.
To take advantage of USB Audio Class 2.0 audio playback supporting up to
384kHz sampling rates you will need to install the Windows driver supplied on
the CD included with the RA-1592MKII. You will also need to switch the RA-
1592MKII to USB Audio Class 2.0 playback mode with the following:
· Press MENU on the front panel until “PC-USB AUDIO CLASS” appears on the
display.
· Select “2.0” using the “-” button then press “ENTER”.
· Power cycle the RA-1592MKII and reboot your PC after changing the USB Audio
mode to ensure both units are properly configured.
Many audio playback applications do not support 384kHz sampling rate. Please
confirm your audio player supports 384kHz audio and you have 384kHz audio
files to properly playback this sample rate. Also, you may need to configure
the audio driver in your PC to output 384kHz or your computer may “down
sample” to a lower audio sample rate. For more information please refer to
your audio player or operating system information.
The RA-1592MKII has been certified as Roon Tested and compatible with Roon
software via PC-USB.
Being Roon Tested means that Rotel and Roon have collaborated to ensure you
have the best experience using Roon software and the RA-1592MKII together, so
you can just enjoy the music.
For the best user experience it is suggested to use USB Audio Class 2.0 when
using Roon.
NOTE: USB Audio Class 2.0 requires installation of the Windows PC driver on
the CD ROM included with the RA1592MKII.
NOTE: MAC computers do not require a driver to support PCUSB 1.0 or 2.0 audio.
NOTE: Upon successful installation of the driver, you may need to select the
ROTEL audio driver from the audio/speaker setup of your computer.
NOTE: Support for MQA and MQA Studio requires USB Audio Class 2.0. Please
select USB Audio 2.0 to support MQA.
RS232 t
The RA-1592MKII can be controlled via RS232 for integration with automation
systems. The RS232 input accepts a standard straight DB-9 Male-to-Female
cable.
For additional information on the connections, software, and operating codes
for RS232 control of the RA-1592MKII, contact your authorized Rotel dealer.
Rotel Link w
Rotel Link is not used for RA-1592MKII.
EXT REM IN Jack e
This 3.5mm mini-jack receives command codes from industry-standard infrared
receivers via hard-wired connections. This feature could prove useful when the
unit is installed in a cabinet and the front-panel sensor is blocked. Consult
your authorized Rotel dealer for information on these external repeaters and
the proper wiring of a jack to fit the mini-jack receptacle.
14
RA1592MKII Stereo Integrated Amplifier
Network Connection =
The RA-1592MKII can be attached to a network using the rear panel
NETWORK socket =. The NETWORK configurations allow both STATIC
and DHCP IP addressing. See the Network section of this manual under Setting
Menu for IP address configuration information.
The NETWORK connection allows software updates to be downloaded from the
Internet. The NETWORK connection also allows IP control for integration with
automation systems.
For additional information on the IP control please contact your authorized
Rotel dealer.
Protection Circuit
The amplifier has both thermal and over-current protection circuitry that
protects the amplifier against damage in the event of extreme or faulty
operating conditions. The protection circuits are independent of the audio
signal and have no impact on sonic performance. Instead, the protection
circuits monitor the temperature of the output devices and shut down the
amplifier if temperatures exceed safe limits.
Most likely, you will never see this protection circuitry in action. However,
should a faulty condition arise, the amplifier will stop playing and will
display “AMP PROTECTION” on the front panel.
If this happens, turn the amplifier off. Let it cool down for several minutes,
and attempt to identify and correct the problem that caused the protection
circuitry to engage. When you turn the amplifier back on, the protection
circuit will automatically reset.
In most cases, the protection circuitry activates because of a fault condition
such as shorted speaker wires, or inadequate ventilation leading to an
overheating condition. In very rare cases, highly reactive or extremely low
impedance speaker loads could cause the protection circuit to engage.
If the protection circuitry triggers repeatedly and you are unable to isolate
and correct the faulty condition, contact your authorized Rotel dealer for
assistance in troubleshooting.
Settings Menu
You can access the settings menu from the front panel by pressing the MENU
9 button or F on the remote. You can change the value of the selected
option by pressing the +/- button on the front panel or up/down/left/right
G arrow buttons on the remote. Step through the sub-menus by pressing the MENU
9 button on the front panel or F on the remote.
· TONE Control: TONE BYPASS ON/OFF, BASS level and TREBLE levels can be
changed to desired settings. Press the ENTER button on the front panel or on
the remote to toggle between the tone setup options. (For more information on
Tone Control refer to the Tone Control Bypass, Bass and Treble control
sections.)
NOTE: These settings are stored permanently even after the RA 1592MKII is
powered off.
· BALANCE: Change left/right balance (For more information on Balance sections
refer to the Balance Control section).
NOTE: This setting is stored permanently even after the RA1592MKII is powered
off.
· DIMMER: Dims the display.
NOTE: This setting is stored permanently even after the RA1592MKII is powered
off.
· POWER ON MAX VOLUME: This sets the maximum volume level when the unit is
turned ON. “45” is the factory default.
NOTE: Power On Max Volume settings do not apply to sources configured with
Fixed Gain.
· POWER OPTION: Enables the RA-1592MKII to be controlled via the network port
when attached to an automation system. The power consumption is higher in
Quick Power mode. If network control is not required select the Normal Power
mode. “Normal” is the factory default.
Valid settings include: Normal, Quick.
NOTE: When the POWER OPTION is configured to Quick, the RA1592MKII will
consume additional power in standby mode.
NOTE: Due to local power consumption regulations the POWER OPTION function is
not available in all markets.
· AUTO POWER OFF: The RA-1592MKII can be configured to automatically power off
if unused for a specified period. If no changes are made to the unit within
the specified “Auto Power Off” time the unit will automatically go to STANDBY
mode. The Auto Power Off timer will be restarted if changes are made to the
volume, source or playback. The default for Auto Power Off is set to 20 MINS.
Valid settings include: 20 MINS (Default), DISABLE, 1 HOUR, 2 HOURS, 5 HOURS,
12 HOURS.
· FIXED GAIN: Configures a Fixed Volume level for a specified input. To enable
this feature press the +/- buttons to select the desired fixed volume level
for Aux 1, USB, PC-USB, Optical 1, Optical 2, Coax 1, Coax 2 or Bluetooth.
When enabled and the input with a Fixed Volume is selected, the Volume level
will immediately be set to the specified level.
Valid settings include: VARIABLE, FIXED 01-95, FIXED MAX.
· AUX1 VOL: VARIABLE (disabled) is factory default.
· USB VOL: VARIABLE (disabled) is factory default.
· PC-USB VOL: VARIABLE (disabled) is factory default.
· OPT1 VOL: VARIABLE (disabled) is factory default.
· OPT2 VOL: VARIABLE (disabled) is factory default.
· COAX1 VOL: VARIABLE (disabled) is factory default.
· COAX2 VOL: VARIABLE (disabled) is factory default.
15
· BLUETOOTH VOL: VARIABLE (disabled) is factory default.
NOTE: The Volume knob on the front panel and Volume +/ buttons on the IR
remote are disabled when the volume is Fixed. To disable this feature set the
Fixed Volume level to “Variable”.
· PC-USB AUDIO CLASS: Change supported PC-USB Audio Class of the attached
device.
NOTE: Some computers attached to the PCUSB do not support USB Audio Class 2.0
and do not support 32 bits /384 kHz audio playback. If needed the PCUSB can be
configured for USB Audio Class 1.0. Please refer to your computer operating
system for details.
· PC-USB AUDIO MODE: Change PC-USB Audio mode to support MQA and PCM Audio up
to 24bits or PCM Audio Only up to 32bits. When 32B ONLY is selected MQA audio
is not supported. To playback MQA the MQA/24B option must be selected.
Valid settings include: MQA/24B (Default), PCM 32B.
· NETWORK: Shows the network connection status and to view/configure the
network settings. If the network is properly configured and attached,
“Connected” will be displayed. To view or modify the network settings, press
the ENTER button.
The RA-1592MKII supports both DHCP and STATIC IP addressing. Select the
desired IP address method and press ENTER.
If DHCP is selected you can refresh IP address by pressing ENTER or press MENU
to view IP address information. Press the MENU button to toggle through IP
address settings. If the IP address is renewed the network will be tested and
connection status reported.
If STATIC IP address mode is selected you must configure all settings for the
network including IP Address, Subnet Mask, Gateway and DNS Server. Use the
up/down/left/right or +/- buttons to adjust the values and press ENTER to move
to the next value. When the proper IP information is configured press MENU to
go to the next setting. After entering the STATIC IP address information the
network will be tested and connection status reported.
NOTE: For more information regarding network connection please contact your
authorized Rotel dealer.
NOTE: A network connection is not required for the RA1592MKII to operate.
· MAIN: This shows the current software version loaded into the RA1592MKII.
The software can be updated if the RA-1592MKII is properly connected to the
Internet.
· Press ENTER to check if a new software version is available.
· If a new software version is available press the + button on the front panel
or the up/right button on the remote control to select YES then press ENTER
button to begin the software update process.
· The new software will be downloaded from the Internet. The RA1592MKII will
power cycle when the software update is complete.
NOTE: Do NOT power off the RA1592MKII during the software update process.
NOTE: It is recommended to Reset Factory Defaults after the software update is
complete.
· PC-USB: This shows current loaded software version for PC-USB processor.
· SIGNAL SENSE: Check if an audio signal is present on the configured Signal
Sense input. The RA-1592MKII monitors the data stream to determine if there is
audio. If there is no audio detected for 10 minutes, the RA-1592MKII will
enter Signal Sense Power Mode. When in Signal Sense Power Mode and the RA-
1592MKII detects audio on Signal Sense input, the unit will automatically
power on. To disable this function, select the OFF option which is the factory
default setting.
NOTE: When the SIGNAL SENSE function is activated, the RA1592MKII will consume
additional power in signal sense standby mode.
NOTE: Due to local power consumption regulations the SIGNAL SENSE function is
not available in all markets.
· FACTORY DEFAULT: This sets the unit back to the original state as when it
left the factory. Press the + button on the front panel or RIGHT arrow button
on the remote control to select
NOTE: All previously configured options will be erased and reset to the
factory default settings.
Troubleshooting
Most difficulties in audio systems are the result of incorrect connections, or
improper control settings. If you encounter problems, isolate the area of the
difficulty, check the control settings, determine the cause of the fault and
make the necessary changes. If you are unable to get sound from the RA-
1592MKII, refer to the suggestions for the following conditions:
Power Indicator Is Not Illuminated
The Power Indicator ring around the power button and the basic items in the
Display window should be illuminated whenever the RA-1592MKII is plugged into
the wall power outlet and the POWER switch is pushed in. If it does not light,
test the power outlet with another electrical device, such as a lamp. Be sure
the power outlet being used is not controlled by a switch that has been turned
off.
Fuse Replacement
If another electrical device works when plugged into the power outlet, but the
Power Indicator still will not illuminated when the RA-1592MKII is plugged
into the wall outlet, it indicates that the internal power fuse may have
blown. If you believe this has happened, contact your authorized Rotel dealer
to get the fuse replaced.
No Sound
Check the signal source to see if it is functioning properly. Make sure the
cables from the signal source to the RA-1592MKII inputs are connected
properly. Check the wiring between the RA-1592MKII and the speakers.
16
RA1592MKII Stereo Integrated Amplifier
Cannot Connect via Bluetooth
If you cannot pair your Bluetooth enabled device to the RA-1592MKII, delete
the memory of the previous connection on your device. On your device this is
often listed as “Forget this Device”. Then try to make the connection again.
Playable Audio Formats
USB Apple (iPhone, iPod, iPad)
Format
Any supported file loaded to Apple device.
Notes
Any supported file loaded to Apple device. Phone may resample depending on
stored format. May exclude Apps designed to play formats not originally
supported by the sending device.
APTX and AAC Bluetooth
Format
Notes
Any format supported May exclude Apps designed to play formats not originally by the sending device. supported by the sending device.
PC-USB Format
Format determined by the Media Player/ Server software that you use.
Notes
Any supported format by the PC software PCM Audio: 44.1k, 48k, 88.2k, 96k,
176.4k, 192k 384k (16 bit, 24 bit and 32 bit) MQA, MQA Studio (24 bits/384kHz)
Roon Tested
Coax/Optical Format
SPDIF LPCM
Notes
44.1k, 48k, 88.2k, 96k, 176.4k, 192k 16 bit, 24 bit
Specifications
Maximum Power Output Continuous Power Output Total Harmonic Distortion
Intermodulation Distortion (60 Hz : 7kHz, 4:1) Frequency Response:
Phono Input Line Level Inputs Damping Factor (20 Hz 20kHz, 8 ohms) Input
Sensitivity / Impedance Phono Input (MM) Line Level Inputs (RCA) Line Level
Inputs (XLR) Input Overload Phono Input (MM) Line Level Inputs (RCA) Line
Level Inputs (XLR) Preamplifier Output Level / Impedance Signal to Noise Ratio
(A weighted) Phono Input (MM) Line Level Inputs
Digital Section Frequency Response Signal to Noise Ratio (IHF “A” weighted)
Input Sensitivity/Impedance Preamplifier Output Level Coaxial/Optical Digital
Signals
PC-USB
“Made for iPod,” and “Made for iPhone,” means that an electronic accessory has
been designed to connect specifically to iPod or iPhone, respectively, and has
been certified by the developer to meet Apple performance standards. Apple is
not responsible for the operation of this device or its compliance with safety
and regulatory standards. Please note that the use of this accessory with
iPod, or iPhone may affect wireless performance.
iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple
Inc., registered in the U.S. and other countries.
Power Requirements: USA: EC:
Power Consumption Standby Power Consumption
Normal Network Wakeup BTU (4 ohms, 1/8th power) Dimensions (W x H x D)
Front Panel Height Weight (net)
350 watts/channel, 4 ohms 200 watts/channel, 8 ohms < 0.008% < 0.03%
20 Hz – 20kHz, 0 ± 0.5 dB 10 Hz – 100kHz, 0 ± 0.5 dB 600
5.2 mV / 47k ohms 340 mV / 100k ohms 540 mV / 100k ohms
52 mV 3.5 V 5.5 V 1.9 V / 100 ohms
80 dB 103 dB
10 Hz – 90k Hz (0 ± 2 dB, Max) 102 dB 0 dBfs / 75 ohms 1.43 V (at -20 dB)
SPDIF LPCM (up to 192k Hz 24 bit) USB Audio Class 1.0 (up to 96kHz 24bit) USB
Audio Class 2.0 (up to 384kHz 32bit) Driver installation required MQA and
MQA Studio (up to 24bits/384kHz) Roon Tested
120 volts, 60 Hz 230 volts, 50 Hz 500 watts
< 0.5 watts < 2 watts 1239 BTU/h 431 x 144 x 425 mm ( 17 x 5 7/8 x 16 ins.) 3U
(132.6 mm, 5 1/4 ins) 17.6 kg, 38.8 lbs.
All specifications are accurate at the time of printing. Rotel reserves the right to make improvements without notice. Rotel and the Rotel Hi-Fi logo are registered trademarks of The Rotel Co, Ltd., Tokyo, Japan.
The Rotel Co. Ltd. Tachikawa Bldg. 1F., 2-11-4, Nakane, Meguro-ku, Tokyo,
152-0031 Japan
Rotel USA Sumiko 11763 95th Avenue North Maple Grove, MN 55369 USA Phone:
510-843-4500 (option 2) E-mail:
Rotelsupport@sumikoaudio.net
Rotel Canada Kevro International 902 McKay Rd. Suite 4 Pickering, ON L1W 3X8
Canada Tel: +1 905-428-2800
Rotel Europe Dale Road Worthing, West Sussex BN11 2BH England Phone: + 44
(0)1903 221 710 Fax: +44 (0)1903 221 525
www.rotel.com
RA-1592MKII Owner’s Manual Ver D 070921 English
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>