BOSS MRWT40RGB.4 4 Inch 102mm 2-Way Marine Waketower/UTV Roll Bar Speakers User Manual

MRWT4ORGB.4
USER’S MANUAL
4″ (102 mm) 2-WAY MARINE WAKE TOWER/UTV ROLLBAR SPEAKERS
FEATURING MULTICOLOR ILLUMINATION OPTIONS

INCLUDES WIRELESS RF
REMOTE CONTROL
WITH KEYCHAIN TAG

Thank you for choosing our product!
Please read the instructions carefully so you will know how to operate your product properly.
If there are any technical questions, please contact: Customer care: 805-751-4853 & Live chat
Online support: www.bossaudio.com/support
IMPORTANT
Please enter below the Serial No. which is located on the exterior of the product. Retain this information for future reference.
Model No. __
Serial No. __
Purchase Date__

Before use

Read and understand all instructions before you use your product. If you do not follow the instructions in this manual, we are not responsible for injury or damage resulting from improper handling. This will also invalidate the warranty.

Important safety precautions

• Be sure to observe the following guidelines:
  -Do not increase speaker volume so high that you cannot hear what is around you.
  -Use caution or temporarily discontinue use in potentially hazardous situations.
• Do not make any adjustments to the product when driving or in other situations where distractions can be hazard­ Responsible and safe driving is your primary responsibility when operating a vehicle.
• Start volume at a low setting then gradually increase the volume until you can hear it comfortably, without sound distortion and ear discomfort.
• In the event of smoke, strange noise, or odor emitted from the product or any other abnormal operational signs appearing on the product, disconnect the product from the power supply. Discontinue use and contact your dealer or our technical support. Using the product in this condition may result in permanent damage to the system.
• Servicing must only be carried out by a technician. Contact our technical support for any service questions.

Installation precautions

• WARNING: Always consult a professional installer.
• Installation must be performed by a professional. Contact our technical support for any installation questions.
• Observe the safety and operating instructions of the devices which are connected to the product.
• Only use attachments/accessories specified by the manufacturer for installation.
• Do not modify this product, as this affects the safety of the product. Risk of injury or damage to the product.
• Before installation, disconnect the negative terminal of the vehicle battery to prevent damage to the product, fire, and/or possible injury.

Introduction

This product has four marine-grade speakers with a 2-way system and is designed to be mounted on a wake tower boat or UN. The supplied clamps allow you to quickly and safely mount the speakers on the proper tubings of your vehicle. The speakers need a connection to your amplifier or head unit for 4 channel audio output.
Each speaker has an RGB LED light with multiple color modes, and you can control LED lights with the supplied remote control.
Please read this manual carefully so you will know how to operate your product properly. After you have finished reading this manual, store it in a safe place for future reference.

Delivery content

• (4) Marine grade speakers
• (4) Mounting clamps (pre-attached to each speaker)
• (8) M6 x 15mm hex bolts and spring washers (pre-attached to each mounting clamp)
• (12) Rubber mounting pads (1/8″ thickness)
• (1) Remote control (CR2025 coin battery inserted)
• (1) Keychain tag
• (1) 12V vehicle battery cable with 3.5mm plug (for LED power)
• (1) LED cable
• User manual and warranty card

Mounting speakers

Important notes on mounting

• The vaunting system is designed to provide a safe and stable installation. However, it is important to remember that these are objects that will be used in an environment that is extremely bumpy and turbulent. Consider this, and use extreme caution when mounting to avoid what may be a serious accident.
• The supplied damps accept the tube size range of 1.5″ — 2″ to attain a strong and safe hold. If some gap around the clamped tube occurs for clamping looseness, use universally available rubber inserts to fill the gap to prevent the movement of the mounted speakers.
• The supplied rubber mounting pads must be used to prevent abrasion and provide more secure clamping.
• The supplied spring washers must be used to provide more stable bolt tightening against vibration.

1. Unpack the speakers. Each speaker is pre-attached with a clamp that has 2 hex bolts and spring washers. Remove the clamps, hex bolts, and spring washers from the speakers. On a speaker, find two holes on the clamp and use a proper hex wrench to loosen the bolts with spring nuts then take the clamp off. Repeat the step above to remove the damps, bolts, and spring washers from the other three speakers.

2. Determine the mounting location and a proper mounting tube on your vehicle. The tube size should be in the range of 1.5″ — 2″ to attain a strong and safe hold by the clamp.

3. Cut the supplied rubber pads to a suitable length, and remove the protective layer. Then stick the adhesive side on the inner surface of the clamp which comes in contact with the mounting tube. Stick another rubber pad on the speaker surface which comes in contact with the mounted tube.

4. Hold the speaker on the mounting tube, and place the clamp on top of the tube, then fasten the damp with two bolts and spring washers.
   Tighten each bolt until you feel resistance, then tighten each of the two bolts a few turns. Tighten both equally to greatly improve the safety of the mounting.

5. Repeat steps 2-4 to mount the other three speakers.

|

To ensure the safety of the mounted speakers, always check the mounting conditions (e.g. the bolt tightness and no clamp damage) of the speaker before each vehicle ride.

---|---

Speaker wire connection

For signal input to the speakers, connect the front and rear speakers to the 4 channel amplifier or head unit on your vehicle. The speakers are also powered by a connected amplifier or head unit.

|

For installation safety points, see “Installation precautions” on page 3.
For safety, disconnect the negative terminal of the vehicle battery prior to wiring.
Note the speaker load for your amplifier or head unit prior to wiring.
Use only high-quality marine-grade wires for reliable installation and to minimize signal or power loss.
Never run wires underneath the vehicle. Always run wires inside the vehicle for the best protection of wires. Make sure wires are not squeezed or damaged by sharp edges. Use rubber bushings for penetrations.

---|---

1. Each speaker has a pair of terminals (red and black). Connect the speaker wire (not included) to the two terminals on the speaker. Be sure to observe correct polarity.
   Press the spring-loaded terminal down, insert the bare wire end into the slot of the terminal, then release the terminal. Repeat the step to insert the wire into the other terminal.

2. Connect the other end of the speaker wire to the audio outputs on your amplifier, OR to the speaker wire leads of your head unit. Be sure to observe speaker polarity.
   If connected to your amplifier, refer to the amplifier’s user manual for proper audio output connection.
   If connected to your head unit, refer to the head unit’s user manual for proper speaker wire lead connection.

3. Repeat the steps above to connect the other three speakers to your amplifier or head unit.
   To retain stereo imaging, make sure the front and rear speakers are correctly connected with respect to the left and right sides.

LED power connection

LED light is equipped in the front of each speaker. Use the supplied LED cable to connect all the speakers to create RGB multicolor illumination.

|

Caution!
The LED lights are powered by a 12V DC vehicle battery. Never connect to any other voltage supply (e.g. 24V DC power supply in trucks or buses).
For safety, disconnect the negative terminal of the vehicle battery before connecting power to the speakers. Make sure wires are not squeezed or damaged by sharp edges. Use rubber bushings for penetrations. Position wires so that no one can trip over or become entangled in them.

---|---

1. Connect the supplied LED cable to four speakers as shown below.
   

2. Connect the supplied vehicle battery cable to the power jack on the speaker which has DC input. Then using high-quality extension wires (not included), connect the DC input speaker to the positive terminal of the vehicle battery. Then reconnect the negative terminal of the vehicle battery. Now the speakers are powered.

LED light control

The product comes with remote control for you to control the RGB LED light in the front of each speaker. Keep the remote control safely using the supplied keychain tap.

1. Turn on or off illumination. Make sure the DC input speaker is con­nected to the vehicle battery.

2. MODE +/-
   Switch to dynamic illumination and select a dynamic model.

3. SPEED +/-
   Switch to dynamic illumination and change a dynamic illumination speed.

4. COLOR +/-
   Switch to static illumination and select a color mode.

5. BRIGHT +/-
   Change illumination intensity.

6. DEMO
   Show nine dynamic illumination modes in sequence. The show repeats three times.

Replace battery
The remote control is powered by a CR2025 coin battery. If the battery is exhausted, replace it with a new battery of the same type.

1. Find the battery compartment at the back of the remote control. Pull the battery tray out.
2. Load a new battery with the correct polarity as shown on the tray.
3. Replace the battery tray. Make sure the tray is securely inserted.

Important notes on battery

• The danger of explosion if the battery is incorrectly replaced. Replace only with the same type or equivalent type. Observe correct polarity while inserting the battery.
• Do not leave the battery near fire or under direct sunlight. Do not place the remote control in hot places (e.g. on the dashboard). This may cause fire, explosion or excessive heat
• Remove the battery from the remote control if it is not used for a long time to avoid battery leakage.
• Do not recharge, dismantle or short-circuit the battery or throw it into the fire. This may cause a risk of explosion or battery leakage. If spilled fluid comes in contact with your skin or clothing, immediately rinse with water and consult a doctor.
• The remote control contains a coin button-type battery, which can be swallowed. Keep the battery out of reach of children at all times! If swallowed, the battery can cause serious injury or death.
  If you suspect that a battery has been swallowed or placed inside any part of the body, seek immediate medical attention.

Care for your product

• DO NOT clean the product in hot weather (e.g. hot sunlight).
• DO NOT use abrasive or highly alkaline cleaner on the product.
• DO NOT use gasoline, acetone, carbon tetrachloride, or other aggressive chemical solutions on the product.
• DO NO T scrape the product with a razor blade or another sharp instrument.
• This product is waterproof against splashing water. However, never submerge the product in water or other liquids.
• Wash the product with lukewarm water and mild soap or detergent using a dean sponge or soft cloth. Rinse well with dean water.

Care of the environment

Product disposal
Do not throw away the product with the normal household waste at the end of its life, but hand it in at an official col­lection point or recycling. By doing this, you help to preserve the environment.
Battery disposal
Batteries must not be disposed of with normal household waste. Recycle them at the collection points provided for this purpose. Contact the local authorities or your dealer for recycling advice. Correct disposal of old batteries helps protect the environment and human health.

Specifications

BOSS Audio Systems
3451 Lunar Court • Oxnard, CA 93030
www.bossaudio.com
805-751-4853 Customer Service
Tech Support: www.bossaudio.com/support

0421

Documents / Resources

| BOSS MRWT40RGB.4 4 Inch 102mm 2-Way Marine Waketower/UTV Roll Bar Speakers [pdf] User Manual
MRWT40RGB.4, 4 Inch 102mm 2-Way Marine Waketower UTV Roll Bar Speakers
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>