EnviroLite 3200LEDC 32 in. Oval Matte Black Integrated 3000K CCT LED Ceiling Light Flush Mount Installation Guide

EnviroLite 3200LEDC 32 in. Oval Matte Black Integrated 3000K CCT LED

Ceiling Light Flush Mount

Please read carefully and save these instructions, as you may need them at a later date.

CAUTION
CAUTION – Risk of Fire. Consult a qualified electrician to ensure the correct branch circuit conductor. min 90°C supply conductors. Turn off the main power at the circuit breaker before installing the fixture in order to prevent possible shock.
GENERAL
All electrical connections must be in accordance with local and National Electrical Code (N.E.C.) standards. If you are unfamiliar with proper electrical wiring connections obtain the services of a qualified electrician. Remove the fixture and the mounting package from the box and make sure that no parts are missing by referencing the illustrations on the installation instructions.

ASSEMBLY AND INSTALLATION

1. Turn off the power.
2. Remove the four decorative nuts (13) from the metal ring (12). Remove the metal ring (12) and acrylic lens (11) from the fixture pan (9).
3. Pull the supply wires (4 & 6) and house ground wire (2) out from the outlet box (1).
4. Position your fixture at the desired location. Be sure the fixture wires (3, 5, & 8) can reach the outlet box (1). Mark the location of the four keyhole slots located on the fixture pan (9). Be sure to mark only the narrow parts of the keyhole slots. Remove the fixture pan (9) from the ceiling. Drill the four holes using the appropriately sized drill bit. Insert the provided ceiling anchors (14) into the holes. Screw the anchor screws (10) halfway into the ceiling anchors (14).
5. Attach the lanyard (16) on the fixture pan (9) to the outlet box (1) using a lanyard screw (15). Connect the supply ground wire (2) to the fixture ground wire (3) using wire connector (7). Connect the white supply wire (4) to the white (or ribbed) fixture wire (5) using a wire connector (7). Connect black supply wire (6) to the black (or smooth) fixture wire (8) using a wire connector (7). Carefully tuck all wires back into the outlet box (1).
6. Place the fixture pan (9) over the anchor screws (10), lining them up with large openings of the keyhole slots. Push the fixture pan (9) flush against the ceiling. Then twist the fixture pan (9) so that the anchor screws (10) slide into the narrow opening of the keyhole slots. Tighten the four anchor screws (10) until the fixture pan (9) is flush with the ceiling.
7. Place the acrylic lens (11) over the fixture pan (9). Place the metal ring (12) over the acrylic lens (11) lining up the holes with the fixture pan (9) posts and securing it with the four decorative nuts (13).

1. Outlet box
2. Supply ground wire
3. Fixture ground wire
4. White supply wire
5. White fixture wire
6. Black supply wire
7. Wire connector
8. Black fixture wire
9. Fixture Pan
10. Anchor Screw
11. Acrylic Lens
12. Metal Ring
13. Decorative Nut
14. Ceiling Anchor
15. Lanyard Screw
16. Lanyard

FCC NOTICE

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC responsible party: Cordelia Lighting
Address: 20101 S Santa Fe Avenue East Rancho Dominguez, CA 90221
Phone: 800-345-0542

NOTICE: This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 14 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference can be determined by turning the equipment off and on, the user is encouraged to try to correct the interface by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the device and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

WARRANTY
Cordelia warrants this product to be free from defects in material and workmanship for five years from the original date of purchase by the consumer. This warranty is limited to the counter replacement at the time of purchase, with the original purchase receipt. Cordelia will not be liable for the loss or damage of any kind, incidental or consequential damages of any kind, whether based on warranty contract or negligence and arising in connection with the sale, use or repair of the product claimed to be defective. Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state. Misuse, accident, improper installation or maintenance will also void the warranty.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>