JOHN LEWIS Limbo Wall fitting User Manual
- June 6, 2024
- John Lewis
Table of Contents
User Manual
Limbo
Wall fitting
Thank you for purchasing this Limbo Wall fitting. Please read the instructions carefully before use to ensure the safe and satisfactory operation of this product. Please keep these instructions for future reference.
Warnings!
This is a Class 1 product and must be earthed.
Please read these instructions carefully before commencing any work. It is
recommended that this fitting be installed by a qualified electrician.
Install in accordance with the IEE Wiring regulations and the Building
Regulations.
To prevent electrocution switch off at mains supply before installing or
maintaining this fitting.
Ensure other persons cannot restore the electrical supply without your
knowledge.
If you are in any doubt, please consult a qualified electrician.
This light fitting should be connected to a 5 amp fused circuit.
If replacing an existing fitting, make a note of the connections.
Always use the correct type and wattage bulb. Never exceed the wattage stated.
When changing a bulb or adjusting the heads, always switch off at the mains
and allow it to cool down. Dispose of used bulbs carefully.
This product is suitable for indoor use only.
This product is suitable for installation on surfaces with normal flammability
e.g. wood, plasterboard, masonry. It is not suitable for use on highly
flammable surfaces (e.g. polystyrene, textiles).
For your safety, always switch off the supply before changing lightbulbs,
cleaning, or removing shades. Always take care when handling lightbulbs to
avoid injury in case of breakage.
Parts List
Installation Instructions
Refer to assembly diagrams. Carefully unpack the carton, making sure all the
parts are present before assembly.
Step 1
Remove the existing fitting, carefully note the position of each set of wires.
Step 2
Remove the fixing bracket from the wall back and attach it to the wall using
the screws provided. Take care to avoid damaging any concealed wiring and
pipes.
Step 3
Having identified the household wiring from your existing light fitting,
connect to the connection block inside the product in the following way:
Check that…..
You have correctly identified the house wires.
The connections are tight.
No loose strands have been left out of the connection block.
Step 4
When completed, ensure that there are no bare or loose strands of wire
exposed, and cover all exposed areas of the connection block with 2 layers of
insulation tape.
Step 5
Ensure the arm is pointing upwards, attach the product to the fixing bracket,
by refitting the screws into the holes in the wall back and tightening the
screws to secure. Take care not to trap any wiring.
Attaching the shade
To attach the glass shades, remove cap nuts and washers. Ensure one washer is
on either side of the glass. Place the glass over the retaining threads and
refit the cap nuts. Do not overtighten.
Care and cleaning
Finish – We recommend cleaning with a soft dry cloth. Do not use abrasive
materials as these will damage the finish.
Glass parts – Remove and wash in warm water or just use a damp cloth. Do not
use abrasive materials as these will damage the finish.
Recommended bulb
1 x 60W
SES Candle
or
1 x 42W
SES Eco Halogen Candle
When changing a bulb, always switch off at the mains and allow the bulb to
cool before handling. Dispose of used bulbs carefully. Do not exceed the
wattage stated or use a different shape bulb from that indicated on the
fitting.
Specification
Maximum wattage: 60W
Voltage: 240V, 50Hz
IP Rating: 20
Weight: 0.3kg
This
symbol indicates that this product should not be treated as normal household
waste and should be recycled. John Lewis does not operate instore take-back,
but as embers of the Distributor Trade Back, the scheme has funded the
development and upgrade of recycling facilities across the UK. Please take it
to your nearest collection facility or for further details contact your local
council or visit www.recycle-more.co.uk.
We have taken great care to ensure that this product reaches you in perfect
condition.
However, should any parts be damaged or missing please contact our Product
Helpline on (01202) 690945.
John Lewis Partnership
171 Victoria Street
London SW1E 5NN
johnlewis.com
Made in China
References
- John Lewis & Partners | Department Store | Home, Fashion, Tech & More
- Everything you need to know to Recycle More
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>