axis APS401T 12/24V Parking Sensor System Installation Guide
- June 6, 2024
- AXIS
Table of Contents
JAPAN QUALITY
APS401T
12/24V Parking Sensor System
GENERAL INSTALLATION DIAGRAM
SENSOR INSTALLATION DIAGRAM
Fix the position of sensors. No obstacle should be detected at 90° from the toview otherwise the system will false alarm.
Installation distance diagram
Installation distance diagram
Installation diagram
ADVISED POSITION TO INSTALL THE SENSOR
| A.
Four drill holes A.B.C.D should be in line.
---|---
| B.
0.5~0.8m vertical to the ground. 0.55m is recommended.
| C. Vertical, tidy surface
without metal components is preferred.
SELECT DRILLING POSITION FOR SENSOR A &D
| A.
Choose suitable drilling positions for the A and D sensor and mark.
---|---
|
For best detection angle, position A & D sensor 1/8 from the edge.
SELECT DRILLING POSITION FOR SENSOR B &C
| A.
Measure the distance between sensors A and D.
---|---
|
Divide distance by 3 and mark sensor B & C.
DRILLING
|
A. Use a small drill bit to locate the position
---|---
| B.
Drill with the bumper cutter supplied.
SENSOR INSTALLATION
|
A. Insert the sensors into the holes and secure them.
---|---
|
B. Arrange to wire neatly and securely.
BUZZER INSTALLATION
|
Paste the buzzer on the center console or the rear of the seat.
---|---
CONTROL BOX INSTALLATION
|
---|---
PARKING SENSOR SYSTEM
This system consists of ultrasonic sensors, a control unit, and a buzzer This system detects the distance between the vehicle and obstructions by ultrasonic sensors installed at the rear of the vehicle. The distance and direction of the obstruction will be shown by an audible buzzer with step-up “BiBi” sounds.
MAIN FEATURES
- Audible buzzer
- Volume Adjustable
- Four stages “BiBi” alarm sound
- Waterproof control box
- Hidden installation
TECHNICAL SPECIFICATIONS
- Rated Voltage: 12V/24V
- Operating Range: DC 10~32V
- Operating Current: 10-120mA
- Detecting Distance: 0.3~1.5m
- Ultrasonic Frequency: 40KHz
- Working Temperature: -20~+70°C
ALARM MODE
| Detecting distance | Alarm sound |
|---|---|
| ≥1.6m | Silence |
| ≥1.1~1.5m | Bi…………Bi………… |
| ≥0.6~1.0m | Bi………Bi……… |
| ≥0.4~0.5m | Bi……Bi…… |
| ≤0.3m | Bi… |
INSTALLATION STEPS
- Carefully choose a position for sensors
- Select drilling position for sensor A&D
- Select drilling position for sensor B&C
- Locate the position and drill
- Install the sensors and hide the wires
- Install the Buzzer
- Install the control box (NOTE: The control box is waterproof)
TEST
- Adjust the direction and orientation of sensors. Neaten the wiring after installation.
- Connect the power wire to the reversing light circuit.
- Connect the wires between the control box and Buzzer.
- After starting the car, the Buzzer will sound one time on power-up. Insert one sensor into the control box port. within 1.0m of hte sensor, it should detect normally.
Disconnect this sensor from the control box and use the same method to check other sensors. Then insert all sensors into matching ports.
NOTE
- The car must be off during the installation
- Performance may be affected in heavy rain, gravel roads, bumpy roads, hot or moist weather, or it the sensor is covered by ice or mud.
- Other ultrasonic or electric waves (eg voltage reducers) may affect the performance of the system.
- The sensors should be installed securely but not over-tight.
- Rubber sensors are designed to avoid “Metal resonance” in metal bumpers.
- Avoid installing the digital control box in areas of interference or moisture.
- Test the system to make sure it works correctly.
- This system is a reversing aid and the manufacturer accepts no responsibility for an accident after the kit is installed.
NOTES
SPECIFICATIONS
GENERAL
– Detection Range:| 0.3 ~ 1.5m
– Rated Voltage:| 12/24V DC
– Operating Range:| 9-32V DC
– Operating Current:| 350mA @ 12V
BUZZER
– Proximity Alert:| Audible Tone
– Audible Buzzer:| Yes
– Buzzer Cable Length:| 15.8m
CONTROL BOX
– Water Resistance| IP67
– Power Leads:| 1.4m
– Dimensions:| 106W x 27H x 80Dmm
SENSORS
– Sensor Type:| Angled Rubber
– Sensor Size:| 20mm
– Sensor Dimensions:| 26W x 26H x 23.8Dmm
– Sensor Cable Length:| 2.1m
– Sensor Installation:| Under Mount or In-Bumper Mount
– Detecting Distance:| 0.3 – 1.5m
– Working Temperature:| -30° to +85°C
– Water Resistance| IP68
– Under-Mount Dimensions:| 61W x 31H x 22.4Dmm
INCLUDES
Control Box
4 x Sensors
Buzzer
4 x Brackets with Pads
4 x 3 Sensor Cable
Drill Bit
WARRANTY
Congratulations on your purchase of a quality Mobile Safety System! You’re joining thousands of satisfied customers who enjoy & experience the benefits of the products we distribute. In the unlikely event that some technical difficulty arises with your purchase, be assured that we are most anxious to see that the problem is quickly rectified to your satisfaction. Please familiarise yourself with the following simple conditions of our warranty. This warranty covers faults through component failure or failure of the product to operate in accordance with published specifications. Product failure as a result of unreasonable environmental conditions, accident, misuse, improper installation, unauthorized repair, vehicle electrical or wiring faults or neglect etc, will not be covered by this warranty. Removal and installation costs, if any, would be paid by the owner as well as any freight or postage costs of transporting the product to AudioXtra. AudioXtra shall not be liable or responsible for any loss or use of this product or any form of consequential loss.
CONSUMER WARRANTY
This product is warranted by AudioXtra Pty Ltd to be free from defects in
materials and workmanship under NORMAL USE for a period of TWENTY FOUR
MONTHS from the date of purchase.
WITHIN 30 DAYS OF PURCHASE DATE:
Please return the unit for replacement to our National Service Centre or the
Retailer from where you made the purchase. All accessories must be included.
Proof of purchase date must accompany the products.
AFTER 30 DAYS OF PURCHASE DATE:
Warranty repair and service is carried out by our National Service Centre.
Repair and service will be carried out at no cost to the owner if proof of
ownership and the date of purchase can be verified to the satisfaction of the
authorized center concerned with this repair. This proof should take the form
of either: a) The warranty card accompanying this product, stamped and
dated by the dealer. b) A Tax Invoice or Receipt showing full details of
the original vendor, purchaser, model number, and serial number.
COMMERCIAL WARRANTY
A product used in or associated with a commercial application will carry a
limited SIX MONTH warranty. An abnormal commercial application is one where
usage, dust, vibration, heat/cold, and other environmental conditions exist at
an extreme level. Our goods come with guarantees that cannot be excluded under
the Australian Consumer Law. You are entitled to a replacement or refund for
a major failure and for compensation for any other reasonably foreseeable loss
or damage. You are also entitled to have the goods repaired or replaced if the
goods fail to be of acceptable quality and the failure does not amount to a
major failure. Please complete the details below in the event of warranty
service being required.
Purchasers Name: ____
Purchasers Address: __
Model Number APS401T **Serial Number __**
Dealer Name: _____ Date of Purchase: / /
Dealer Address:___
Invoice/Sales Docket no: ___
General Hints: To expedite service and prompt return of the equipment, please:
a) Clearly describe the fault in detail
b) Safely and securely pack the unit for transport
c) Include your return address
d) Provide proof of purchase date as outlined above
National Service Centre:
10 STODDART ROAD, PROSPECT, SYDNEY NSW 2148 Australia Telephone: (02) 8841
9000 Fax: (02) 9636 1204
email: services@audioxtra.com.au
Documents / Resources
| axis
APS401T 12/24V Parking Sensor
System
[pdf] Installation Guide
APS401T, 12 24V Parking Sensor System
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>