AUTEL MaxiSys MS909CV User Guide
- June 6, 2024
- AUTEL
Table of Contents
**AUTEL MaxiSys MS909CV User Guide
**
Product Description
MaxiSys MS909CV provides the full functionality and online repair information
you need when diagnosing vehicles, identifying faults and researching repair
issues. It features a powerful octa-core processor and 9.7-inch TFT-LCD
capacitive touchscreen for swift diagnosis and optimum viewing. As an
intelligent diagnostics and information system, MaxiSys MS909CV not only
displays the relevant repair fixes and cases gathered from experienced
industry experts, but provides step-by-step guidance to ensure the repair is
done correctly and efficiently.
MaxiSys MS909CV has three main components:
- MaxiSys Display Tablet — the central processor and monitor for the system
- VCI — vehicle communication interface
- B200 — battery & electrical system tester
- 7” TFT-LCD Capacitive Touchscreen
- Ambient Light Sensor — detects ambient brightness
- Power LED
- Front Camera
- Microphone
- Speaker
- Collapsible Stand — extends from the back to allow hands-free viewing of the tablet
- Rear Camera
- Camera Flash
- Headphone Jack
- USB Port
- USB Port
- Mini USB Port
- HDMI (High-Definition Multimedia Interface) Port
- Mini SD Card Slot
- DC Power Supply Input Port
- Lock/Power Button — Iong press to turn on/off the Display Tablet, or tap to lock the screen
MaxiFlash VCI
- DC Power Supply Input Port
- Vehicle Data Connector
- Ethernet Port
- Vehicle LED
- Connection LED
- Power LED
- USB Port
LED Description
LED
| Color|
Description
---|---|---
Power LED
|
Yellow
| The VCI is powered on and performing self-check.
Green
| The VCI is ready for use.
Red
|
- Lights solid red when system failure occurs.
- Flashes red when the VCI is upgrading.
Vehicle LED
| Green| Flashes green when communicating with the vehicle.
Connection LED
|
Green
| Lights solid green when the VCI is oonnected via USB cable.
Cyan
| Lights solid cyan when the VCI is connected via Wi-Fi.
Blue
| Lights solid blue when the VCI is connected via Bluetooth.
MaxiBAS B200
- Power Button
- Status LED
- Power LED
- USB Port
- Battery Clamp Cable
- Aviation Plug
- Positive Clamp Cable Port
- Negative Clamp Cable Port
LED Description
LED
|
COIO£
|
Description
---|---|---
Status LED
|
Green
|
- Solid Green: The tester is connected via USB cable.
- Flashing Green: The tester is communicating via USB cable.
Blue
|
- Solid Blue: The tester is connected via Bluetooth.
- Flashing Blue: The tester is communicating via Bluetooth.
Red
|
- Flashing Red: Battery clamps are connected to the wrong battery terminals.
Power LED
|
Green
|
- Solid Green: The tester is powered on and the battery is sufficiently charged.
- Flashing Green: The tester is charging; turns to solid green after its battery is fully charged.
Red
|
- Flashing Red: The tester’s battery level is low. Please charge.
GETTING STARTEED
IMPORTANT: Before operating or maintaining this unit, please read these instructions carefully, and pay extra atten- tion to the safety warnings and precautions. Failure to use this product properly may cause damage and/or personal injury and will void the product warranty.
WARNING: The MaxiFlash VCI is compatible with Autel main cable V2.0 and USB cable V2 only.
Establishing Vehicle Communication
-
Connect the main cable V2.0 to the Vehicle Data Connector on the VCI unit and tighten the thumb screws.
-
Connect the cable’s 16-pin adapter to the vehicle’s DLC, which is usually located under the vehicle’s dashboard.
- Choose an adapter (Deutsch-6. Deutsch-9) according to diagnostic connector in the vehicle.
- Choose an adapter (Deutsch-6. Deutsch-9) according to diagnostic connector in the vehicle.
-
Power up the tablet Ensure the tablet is sufficiently charged Of Is connected to the DC power supply.
-
Select one of the three methods shown below( Bluetooth. Wi-Fl or USB cable V2) to connect the tablet with the VCI device and establish a communication link. Only use the supplied USB cable when programming.
-
When thethe VCI device is properly connected to the vehicle and the tablet. the VCI status button on the bottom bar of the screen will display a green badge indicating the Platform is ready to start vehicle diagnosis.
Inspecting the Battery
Before starting a test, observe the battery for:
- Cracking, buckling or If you see any of these defects, replace the battery.
- Corroded, loose or damaged cables and Repair or replace as needed.
Corrosion on the battery terminals, and dirt or acid on the case top. Clean the case and terminals using a wire brush and a mixture of water and baking soda. Wear protective glasses and gloves when working with batteries
IMPORTANT: Please ensure that the MS909CV is powered ON when pairing the device and during registration
Connecting to a Battery
-
Press and hold the Power Button to turn on the Ensure that the unit is sufficiently charged before using.
-
Enable Bluetooth on the
-
Open the Battery Test app and follow the on-screen instructions to pair the MS909CV with the B200 via Bluetooth
-
Connect the red clamp to the positive (+) terminal and the black clamp to the negative (—) terminal of the
Connecting the Multimeter
-
Plug the red test lead into the red input of the multimeter, 2. Connect the red aligator dip/red probe to the other end and the black test lead into the black input. of the red test lead, and the black alligator clip/black probe to the black test lead.
-
Power on the MS909CV and tap the Multimeter button to enter the application.
-
Connect the multimeter to the multimeter cable port of the MaxiBAS 8200 Series Tester and tighten the connector of the multimeter.
-
To use the current clamp with the multimeter when performing the in-vehicle test, tap the Settings icon. Locate the Current clamp on the menu list and swipe the toggle button to the ON position.
-
Plug the red output cable into the red input of the multimeter, and the black output cable into the black input. Connect the multimeter to the MaxiBAS B200 Series Tester and tighten the connector of the multimeter.
Thank you for purchasing this AUTEL MaxiSys MS909CV. Our tools are manufactured to a high standard and — when used according to these instructions and properly maintained — will provide years of trouble-free performance.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>