SAFEGUARD LRA-D1000S Plug-In Strobe Kit U User Manual

: June 6, 2024
: SAFEGUARD

Table of Contents

SAFEGUARD LRA-D1000S Plug-In Strobe Kit U
PARTS & FUNCTION
- LRA-DCRXS Plug-In Strobe Receiver
- LRA-PBTXA Wireless Push Button
THINGS TO KNOW PRIOR TO USE
PRODUCT FEATURES
Battery Installation
TRANSMITTER PAIRING & MELODY
LRA-PBTXA MOUNTING OPTIONS
CHANGING THE MELODY
CLEARING TRANSMITTER MEMORY FROM RECEIVER
SAFEGUARD SUPPLY CONTACT INFORMATION
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SAFEGUARD LRA-D1000S Plug-In Strobe Kit U

PARTS & FUNCTION

LRA-DCRXS Plug-In Strobe Receiver

LRA-PBTXA Wireless Push Button

THINGS TO KNOW PRIOR TO USE

These instructions illustrate pairing a push button to the receiver. For other types of transmitters, follow the same process in step #5 in the “TRANSMITTER PAIRING & MELODY SELECTION”
If your products are not automatically paired, please refer to the section below labeled “TRANSMITTER PAIRING & MELODY SELECTION”
Each LRA-DCRXS (receiver) can pair with a total of two wireless transmitters
Once two (2) transmitters have been paired to a receiver, you cannot add an additional transmitter unless you delete a transmitter from the receiver
There is no limit to the number of receivers you can pair with a transmitter

PRODUCT FEATURES

Wireless range from transmitter to receiver is up to 1,000 ft.(line of sight)
Each receiver can pair with a total of two (2) transmitters
Receiver has three (3) operating modes; a) sound only, b) strobe only & c) sound & strobe
Assign one (1) of eighteen (18) available melodies to each transmitter
Strobe has two flashing patterns; a) slow & b) fast
Operating frequency: 915MHz
Operating temperature: 32F to 104F
Product dimensions: 2.5” L x 1.2” W x 4.72” H
Product weight: .25 lbs

Battery Installation

Use the ﬁnger to unlock the lock lever
Rotate the mounting bracket and bell press into 90 degree.
Remove the mounting bracket from the unit.
Rotate the Battery cover using a coin.
Insert a CR2032 battery to battery compartment provided.
Close the battery cover using a coin.

TRANSMITTER PAIRING & MELODY

If push button & receiver are purchased together as a kit (LRA-D1000S) then the included push button is already paired to the included receiver.

TRANSMITTER PAIRING & MELODY 01

Step 1: Insert the included battery into the transmitter (push button).
Step 2: Plug the receiver into a standard wall outlet.
Step 3: Press on hold the • Learn button for three seconds. A red LED light will blink indicating the unit is in pairing mode. If the light is solid, this means there are already two transmitters paired and you must clear the transmitter memory from the receiver.
Step 4: Press the melody selector button to scroll through available melodies. Once you hear a melody you prefer, do not press any button as the melody is set for the transmitter (push button).
Step 5: Once the melody is selected, trigger the transmitter by pressing the push button. If you are pairing a different type of transmitter, trigger that transmitter by following the instructions provided for that transmitter.
Step 6: If successful, the receiver will generate a short tone. Press the learn button again to exit the programming mode. The unit is now ready to use.

LRA-PBTXA MOUNTING OPTIONS

CHANGING THE MELODY

Press + hold the learning button .or 3 seconds to enter the pairing mode. Press the melody selector button to select the melody desired. Once you hear the melody you want for the transmitter, trigger the transmitter to lock in that sound.

CLEARING TRANSMITTER MEMORY FROM RECEIVER

The receiver can only pair with two (2) transmitters at a time. If you need to replace a transmitter after two are already locked in, you must delete all memory from the receiver by following the instructions below.

Press + hold the, learn button or 3 seconds to enter the pairing mode. Press + hold the, learn button + melody selector button together or 3 seconds to delete the memory)

The receiver will generate a beep tone to indicate all transmitter on the memory is deleted) the red L26 will change to blink). Now you can pair new transmitter to the receiver)