POPP POPE700700 RF433 Bridge User Manual

RF433 Bridge
POPE700700
POPE700717

Quick start:

1. Connect the device to a USB port.
2. If the LED flashes purple, connect to the open Wi-Fi bridge433-XXXX.
3. Enter the IP address 192.168.4.1 in the browser bar.
4. Set in the configuration mask your Wi-Fi, the IP address, and the communication port of your gateway. ( 8000 )
5. Save the setting and activate the bridge.
6. Install the RF433 application in the POPP Hub.

Configuration of the RF433 Bridge

1. Wi-Fi – settings :
   SSID: Enter the name of your home Wi-Fi.
   Password: Enter the password of your home Wi-Fi.
   Scan: Scan the environment for existing Wi-Fi networks
   (If the page remains empty, please check your wireless connection to the bridge).
   DHCP: If checked, the IP address assigned by your router is used.
   IP/Netmask: Specify the IP address and network affiliation of the bridge.
   Gateway: Enter the IP address of your router.

2. SmartHome Gateway – Settings:
   IP: Enter the IP address of your Smart Home Gateway (POPP Hub).
   Port: Enter the communication port to your SmartHome Gateway. Advanced settings: Code send repeats: Set the number of transmission repetitions of a command
   (minimum 1; maximum 25). This may be necessary for some devices with poor communication.

3. Save Settings: Save the settings.

4. Activate Bridge: Activate the 433Mhz bridge. The device restarts and then connects to your Wi-Fi and SmartHome Gateway. Reset Settings: Resets the unit to factory settings.

LED indication:

Configuration mode:

To start the configuration mode, press the button on the 433 Mhz bridge for 4 seconds. The configuration mode is indicated by a purple flashing. This mode can only be terminated via the configuration interface.

Resetting the device to the factory settings:

Press the button on the 433 Mhz bridge for 4 seconds, the unit switches to configuration mode, which is indicated by a purple flash. Press the button again for 4 seconds, the LED changes to yellow before the unit restarts and returns to the factory settings.

Sources of error:

IP address of the SmartHome Gateway within the configuration mode.
Glowing yellow| Does not get an IP address assigned| Check the DHCP settings on your router and in the configuration mode of the gateway. Specify a static IP address.
Glowing yellow| Port settings do not match between 433Mhz Gateway and SmartHome system| Check the transfer port within the configuration mode of the 433Mhz bridge and in your SmartHome Gateway. This is 8000 by default.
Blue flashing (min. 10s)| Wi-Fi connection could not be established| Within configuration mode, check the SSID and password.
Glowing red| A connection to the Wi-Fi is not possible| Within configuration mode, check the SSID and password.

Support

If you encounter a problem, please use the international community at www.z-wave.info (English) or www.zwave.de (German), our website at www.popp.eu/support or contact us by e-mail: info@popp.eu

Declaration of Conformity
Popp hereby declares that this device complies with the essential requirements and other relevant provisions of Directive RED 2014/53/EU. The complete declaration of conformity can be found at the following address: www.popp.eu/ce

Questions regarding the declaration of conformity should be addressed to the following address: Popp & Co, Große Johannisstr. 7, 20148 Hamburg, Germany

Disposal guidelines

Electronic devices may not be thrown away in domestic waste but must be disposed of separately. Please inform yourself about your local legal regulations and the disposal system available to you. Disposing of electronic equipment in landfills or dumps can cause hazardous substances to enter groundwater and above into food and ultimately endanger your health.

References

• Support - popp.eu
• Z-Wave Europe - The leading european distributor for Smart Home products.
• Z-Wave Europe - The leading european distributor for Smart Home products.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>