EZ-ACCESS SUITCASE Singlefold Ramp Portable ramp Instructions
- June 6, 2024
- EZ-ACCESS
Table of Contents
EZ-ACCESS SUITCASE Singlefold Ramp Portable ramp
SYMBOLS
The WARNING symbol indicates a potentially hazardous condition/situation.
The warnings throughout this document, and on your equipment, if any, are for
the protection of people and property. Failure to abide by warnings will
result in a waiver of all liabilities, loss of your warranty, and could result
in equipment damage and or failure, property damage, risk of serious bodily
injury, and or death to operators, riders, and those nearby. The symbol may
appear in various colors and in conjunction with other symbols.
The NOTE symbol indicates important information. Failure to obey all notes
could result in improper operation, less-than-optimum equipment performance,
and at the sole discretion of the equipment manufacturer, may void your
warranty. The symbol may appear in various colors and in conjunction with
other symbols.
WARNINGS
Maximum weight capacity is 800 lbs.; never exceed weight capacity.
Prior to assembly and use, read and follow all instructions, warnings, and
labels. Following all instructions and obeying all warnings before and during
use is necessary for safe operation.
For additional information or to obtain replacement copies of instructions or
labels, call 1-800-451-1903. For
wheelchairs and scooters only; not for commercial use.
Before use, refer to your mobility equipment’s owner guide for acceptable ramp
usage, including proper slope/incline, chair direction, etc.; never exceed its
recommendations.
Only use the ramp with a qualified helper and always use a lap belt.
Before each use, check the ramp for worn, loose, or damaged parts. If you find
any of these conditions, do not use the ramp. Contact your dealer for service
or repairs; failure to do so may cause injury.
Do not use the ramp if it is damaged or unstable.
Do not tamper with, attempt to repair, or modify any portion of the ramp.
Use caution when folding and unfolding the ramp to avoid all potential pinch
points.
Ensure that the landings the ramp will be placed on are substantial and of
sound construction.
Use only if the secure, unobstructed, level landings can support, at minimum,
the same weight capacity as the ramp (800 lbs.).
Ensure that the surface area of both top lip transition plates fully overlaps
a secure, unobstructed, level landing enough to safely install provided clevis
pins or other non-provided anchoring hardware, and rests firmly against the
upper landing. If a secure, unobstructed, level landing cannot be attained, do
not use the ramp.
Ensure that the ramp is securely anchored before each use.
Use only if sufficient maneuvering room is available at both ends of the ramp
to assure safe travel when entering and exiting the ramp.
The ramp surface may be slippery in wet conditions; use caution if the surface
is wet as traction may be reduced.
**** Do not use the ramp if its surface is covered with ice, snow, dirt,
leaves, or other debris. Remove all accumulations and sweep the surface clean
before use.
Improper use of the ramp could result in serious injury.
Always exercise caution when handling, installing, and or using the ramp.
GETTING STARTED
- Read this instruction manual in its entirety before use and follow all instructions before and during use.
- Before use, refer to your mobility equipment’s owner guide for acceptable ramp usage, including proper slope/incline, chair direction, etc.; never exceed its recommendations.
- Before each use, check the ramp for worn, loose, or damaged parts. If you find any of these conditions, do not use the ramp.
- Confirm that all package contents are present. Open the shipping box and inspect for damaged or missing parts. If damaged or missing parts are noted, do not use the ramp.
PACKAGE CONTENTS
QTY
| DESCRIPTION|
IMAGE (NOT SHOWN TO ACTUAL SIZE)
---|---|---
1| EZ-ACCESS® SUITCASE® SINGLEFOLD RAMP| 
2| CLEVIS PIN| 
3| INSTRUCTIONS| 
CARE AND MAINTENANCE
-
Before each use, check the ramp for worn, loose, or damaged parts. If you find any of these conditions, do not use the ramp.
Do not tamper with, attempt to repair, or modify any portion of the ramp. -
Keep the ramp surface clear of ice, snow, dirt, leaves, and other debris. For ice and or snow, remove all accumulations and sweep surface clean. For dirt, leaves, and other debris, sweep surface or wash with a soft bristle brush and non-alkaline detergent; rinse well.
The ramp surface may be slippery in wet conditions. Use caution if surface is wet as traction may be reduced. -
Store the ramp in a cool, dry place when not in use.
SET UP AND USE
-
The ramp is shipped fully assembled. To unfold for use, position the folded ramp so that the top lip transition plate (located on the end of the ramp that is labeled TOP) fully overlaps a secure, unobstructed, level landing and is securely supporting the ramp (FIG. 1).
-
Unfold the ramp, exposing the slip-resistant tread surface, then center the ramp on the upper landing (FIG. 2).
-
Ensure that the surface area of both top lip transition plates fully overlaps a secure, unobstructed, level landing enough to safely install provided clevis pins or other non-provided anchoring hardware, and rests firmly against the upper landing (FIG. 3).
a. If the top lip transition plates are not long enough to fully overlap a secure, unobstructed, level landing, a SUITCASE® Top Lip Extension (TLE’) is an available option (sold separately). SeeOPTIONAL ACCESSORY’ section for more information. -
Securely anchor the ramp to the upper landing (FIG. 2).
Ensure that the ramp is securely anchored before each use.
a. TEMPORARILY: To attach temporarily using the provided clevis pins, position the ramp securely and use the hole in each top lip transition plate as a template to drill corresponding ¼” holes into the upper landing (ensure drilled holes are deep enough to fully seat each clevis pin). Fully insert a clevis pin (FIG. 3) through the pre-drilled hole in each top lip transition plate and into the corresponding drilled holes in the landing.
b. SEMI-PERMANENTLY: To attach semi-permanently using non-provided anchoring hardware, position the ramp securely and use the hole in each top lip transition plate as a template to identify anchor locations. Install non- provided anchoring hardware flush with the surface of each top lip transition plate and ensure that it does not create a hazard.
Semi-permanent anchoring hardware is not provided.
When using non-provided anchoring hardware, follow hardware manufacturer’s installation instructions, ensuring that hardware is of sufficient type and size to prevent ramp slippage or undo movement.
OPTIONAL ACCESSORY
- If the ramp’s top lip transition plates are not long enough to fully overlap a secure, unobstructed, level landing, a SUITCASE® Top Lip Extension (`TLE’) is an available option that increases the standard 3″ reach of the top lip transition plates to 9″, in many cases, allowing the ramp to clear an obstruction to create a smooth transition. Visit www.ezaccess.com or call 1-800-451-1903 for more information.
Use of the TLE reduces overall ramp weight capacity to 500 lbs.; never exceed weight capacity.
If a secure, unobstructed, level landing cannot be attained, do not use the ramp.
INCLINE CHART
An incline chart is provided below, however, it is intended only as a
guideline. Before using the ramp, refer to your mobility equipment’s owner
guide for the proper slope/incline, acceptable usage, chair direction, etc.;
never exceed its recommendations.
TO ESTABLISH THE PROPER RAMP LENGTH
- Determine the incline that your chair is designed to climb.
- Measure the rise (distance from top step, porch, van, etc. to the ground).
- Refer to Incline Chart to find proper ramp length.
At any incline, use ramp only with a qualified helper and always use a lap belt.
References
- EZ-ACCESS - Ramps | Wheelchair Ramp | Door Threshold | Carriers & More
- Ramp Warranty Satisfaction | EZ Access
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>