Fenix WT25R Rechargeable Pivoting Work Light User Manual

Fenix WT25R Rechargeable Pivoting Work Light

• One CREE XP-l HI LED, with a lifespan of 50,000 hours.
• 1000 lumens maximum output and 220 meters maximum beam distance.
• 105″ adjustable head for use at different angles.
• Magnetic: tai for hand-free use.
• Magnetic: charging with 1he Included magnetic: charging cable.
• Included a 3400 mAh 16650 rechargeable Li-ion battery.
• Battery level indication for instant checking of remaining battery IBVBI.
• Lockout function avoids accidental activation
• Intelligent 0\18rheet protection against high surface temperature
• Intelligent memory circuit recalls the last used brightness level.
• Weight: 4.83 oz/ 137 g (Including battery)
• Size: 5.33″ x 1.16″ x 0.95″ I 135.3 x 29A x 24.1 mm

OPERATING INSTRUCTION

On/off
With the light switched off, press and hold the switch for 0.5 seconds to tum on the light.
With the light switched on, press and hold the switch for 0.5 seconds to turn off the light.

Output Selection
In general mode, single click the switch to cycle through low>Med>High>Turbo.
In flash mode, single click1he switch to cycle through Strobe>SOS.

Node Switching
In general mode, press and hold the switch for 1.2 seconds to enter strobe of flash mode.
In flli8h mode, press and hold ‘the switch for 1.2 seconds to enter the last used output of general mode

Leek/Unlock
Look: with the light unlocked and switched off, double click the switch to lock the light, the light will blink twice on Low to indicate locked status. Unlock: with the light locked and switched off, double dick Iha switch, the light will be unlocked and activated on Low.
In locked status, dicking or pressing the switch will activate 2 one­ second blinks on Low to indicate locked status.

INTELLIGENT MEMORY CIRCUIT

The light memorizes the last selected output of general mode. When turned on again the previously used output of general mode will be recalled. Each Lime the flash mode is entered with strobe.

TECHNICAL PARAMETERS

BATTERY LEVEL INDICATION

With the light switched off, single click the switch to check the battery status, the indicator will last for 5 seconds.

• Four lights on: 100% – 80%
• Three lights on: 80% – 60%
• Two lights on: 60% – 40%
• One light on: 40% – 20%
• One light Hashes: 20% – 0%

MAGNETIC CHARGING

1. When charging is needed, connect the USB A port of the charging cable to a USB power source, then hold 1he magnetic end of the charging cable close to the lla9hllght The charging cable will attach to the charging port automatically and charging will begin. The indicator on the charging cable will be on and display red to indicate c:liarging status, when the indicator turns green, the charging is completed.
2. Recharge a stored light every four months to maintain optimal battery performance
   Note: The normal charging 1ime is approximately 4 hours and 30 minutes of the Included Fenix ARB-L18-3400 rechargeable Li-Ion battery from depletion to full charging.

BATTERY REPLACEMENT

Loosen the lock catch and open the tail cap to insert the battery with the anode side (+) towards the light head, then close the tail cap and fasten the lock catch.

INTELLIGENT OVERHEAT PROTECTION

The light will accumulate a lot of heat when used on Turbo output level for extended periods. When the light reaches a temperature of 60°C or above, the light will automatically step down a few lumens to reduce 1he temperature. When the temperature drops below 60°C, it will then allow the user for the reselection of Turbo made.

LOW VOLTAGE WARNING

When the voltage level drops below the preset level, 1he flashlight is programmed to downshift to a lower br1ghtll8ss level until Low output is reached. When this happens in Low output, one of the battery level indicators blinks to remind you to recharge or replace the battery.

USAGE AND MAINTENANCE

• Disassembling the 11ealed head can cause damage 1o the light and will void the warranty.
• Fenix recommends using an excellent quality battery.
• If the light will not be u11ad for an extended period. remove the battery, or the light could be damaged by electrolyte leakage or battery explosion.
• Lock the light or remove the battery lo prevent accidental activation during storage or transportation.
• Long-term use can result in 0-ring wear. T□ maintain a proper water seal, replace the ring with an approved spare.
• Periodic: cleaning of the battery contacts improves the lamp’s performance as dirty contacts may cause the lamp to flicker, shine intermittently or even fail to illuminate for the following reasons:
  A: The battery needs replacing.
  Solution: Replace battery pack /battery (Ensure battery i8 inserted according to the manufacturer’s specifications)
  B: The threads, PCB board contact or other contacts are dirty. Solution: Clean the contact points with a cotton swab soaked In rubbing alcohol.
  If the above methods don’t work, please connect your authorized distributor.

INCLUDED

WT25R flashlight, ARB-L 18-3400 rechargeable Li-ion battery, USB magnetic: c:liarging cable, Lanyard, Spare 0-ring, Reminder tag, Information leaflet, User manual, warranty card.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>