RH-PETERSON REAL FYRE Display LED Light Kit RFDL-08 User Guide

Display LED Light Kit
Model #: RFDL-08
INSTALLER: Leave these instructions with the consumer.
CONSUMER: Retain for future reference.

This LED Light Kit is for installation on a Real Fyre Display Rack. To install, see the following steps.
Note: The header light strip (that installs behind the Real Fyre logo) is only compatible with the new 2020 Headers. A retrofit kit (RFD-05-08KIT) is available to replace the header (and add side panels) on original Display Racks.
For RFDA-08 models, only one shelf light assembly can be installed on the top shelf.

PARTS LIST

GETTING STARTED

TOOLS REQUIRED

• Phillips screwdriver
• Power drill
• 7/16″ open-end wrenches (or equivalent)
• 0.2″ drill bit
• Phillips head drill driver

WIRE DIAGRAM

ASSEMBLE DISPLAY RACK (not included)
If not already done, follow the instruction manual(s) provided with your display rack for proper installation.
Note: Do not install the header panel or top channel at this time. If already installed, remove the two pieces. (To allow for light kit installation.)

LED LIGHT KIT INSTALLATION

1. Original RFD-05A models: The supplied template allows for a retro-fit on RFD-05A racks. Place the template on the top shelf and mark. Repeat for the middle shelf. Then drill the holes (use 0.2″ drill bit).
   2020 RFD(A)-08 models: Knock out the 3 small holes at the front of the top shelf. Repeat for the middle shelf.
   

2. Align a shelf mounting bracket onto a shelf light strip, and fasten using the drill and two #10 x 3/8″ Phillipsscrews. Repeat for the second shelf assy.
   3. Install a shelf light assembly onto the top display shelf using the drill and three #10 x 3/8″ Phillips screws. Repeat for the middle shelf (if applicable).

• For RFDA-08 models, only one shelf light assembly can be installed on the top shelf.

INSTALLATION (CONT.)

4. Knock out the two holes in the rear panels, just below the top and middle shelves (right or left side). Then route the shelf light strip wires through the holes.
5. Stick a cable clip beneath the top shelf as shown. Then secure the light strip wire in place. Repeat for beneath the middle shelf (if applicable).
6. Place the header l i g h t s t r i p o n t o t h e header mounting bracket, and secure using the two provided zip ties.
7. Partially loosen the two screws holding the sign cutout in place (use a Phillips screwdriver and a 7/16″ wrench).
Then drop the header light assembly in place, shift forward under the screws, and fasten.
Note: Header light assembly is only compatible with new 2020 headers.
8. Locate the rear panel supplied with the display. Knock out the hole in the panel, (right or left side). Slide in the panel as shown.

• The holes on the panel must face downward.
• Route the header light strip wire through the hole.

9. Locate the top channel supplied with the display. Insert the channel, and fasten using the drill and two 1/4″ – 20 x .5″ Phillips screws (supplied with display).
10. Connect one of the wire extensions to the header light strip wire. Connect the second extension to the middle shelf light strip wire (if applicable).

• For RFDA-08 models, only one extension is needed (for the header light strip wire).
  11. From the rear of the unit, connect the splitter to the light strip extensions/wires as shown.

12. From the rear of the unit, connect the splitter, remote receiver/wire, and power supply as shown.
Route the power supply cord to a 120VAC (15 AMP minimum) GFCI GROUNDED 3-wire receptacle and connect.

13. Stick the four cable clips in the specific areas as shown. Then secure the wires in place.
Note: Place the four clips exactly as shown. The positions allow for proper support of the wires.

REMOTE OPERATION

Your kit comes with a remote to control the LED light system.
ORIENTATION
Prior to remote transmitter use, familiarize yourself with the transmitter keys as illustrated in Fig. 7-1 and Fig. 7-2.

The remote has two modes:
DYNAMIC MODE: 22 effects that range between a fade, strobe, blasting flash, flicker, and alternating color patterns.
STATIC MODE: 20 standing color options (no effects).
Identify the transmitter keys:
1) POWER KEY: Turns the light system on or off.
2/9) DYNAMIC MODE KEYS: Switch to dynamic mode, and switch between dynamic effects (1-22).
3/10) DYNAMIC SPEED KEYS: Switch to dynamic mode, and decrease/increase playing speed (1-8 levels).
4/5) STATIC COLOR KEYS: Switch to static mode, and switch between standing colors (1-20).
6) DIRECT COLOR KEYS: Shortcut keys to main ( static) colors.
7/8) STATIC BRIGHTNESS KEYS: Switch to static mode, and decrease/increase brightness (1-8 levels).
11) DEMO KEY: S witch/reset to dynamic mode #1.
REMOTE USE
Note: The light system always retains the memory of all remote transmitter settings.

1. Press the POWER key on the remote transmitter to turn the light on or off (see Fig. 7-1).
2. Use the remote as desired. Reference the above section and Fig. 7-1 and 7-2.
   

SHUTTING DOWN
Press the POWER key on the remote transmitter.
REMOTE STORAGE
When not in use, store the remote transmitter in a safe location.

TROUBLESHOOTING

If you have trouble with your LED lights, please use this list to identify the problem. By trying one or more of the solutions to the probable cause, you should be able to solve the problem. If this list does not address your present problem, or if you have other technical difficulties with your unit, please contact your local dealer or visit our website at www.rhpeterson.com.

LED lights will not turn on, off,
or function using the remote transmitter|

1. Transmitter battery dead
2. Loose wires
3. The appliance is not receiving power
4.  Power supply failure
5. Tra n s m I t t e r m a l f u n c t I o n /damaged
6. Receiver malfunction/ damaged

|

1. Check/replace the battery in the transmitter (see BATTERY REPLACEMENT section below).
2. Check all wires are connected properly.
3. Check that the power supply cord is properly plugged in. Check GFCI. Check to build circuit breaker.
4. Check/replace the power supply.
5. Replace the remote transmitter.
6. Replace remote transmitter.

BATTERY REPLACEMENT

The remote transmitter requires one lithium battery (3V/ CR2025) to operate (included). Locate the transmitter, remove the tray (found at the bottom), and properly insert the new battery as shown. Re-secure the tray. See Fig. 8-1.

ROBERT H. PETERSON CO.
• 14724 East Proctor Avenue
• City of Industry, CA 91746
L-A2-464
REV 0 – A – 2010210845

References

• rhpeterson.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>