CAMECHO B08X2N8X2Z 7 Inch Touch Screen Car Stereo Double Din Car Radio User Manual

CAMECHO B08X2N8X2Z 7 Inch Touch Screen Car Stereo Double Din Car Radio

Preface:

• In xrder to prevent injuries and fires, pis pay attention to the following insructions:
• In order to prevent short circuit and soon, do not drop the metal ohects it the device.
• If there is smoke or peculiar smell the device. pis tum Off the power at once.
• Please do not make the device falling or strong collision. in order to prvent device failure, pis observe the following note:
• Please do not install the device in the place of strong sunlight high tenperature, high humidity or dusty.
• Please replace the fuse which is the same specification If you are usng different specification of the fuse, may cause failure of the device.
• In order to prevent short circuit pis pull out the power wire when yes replace the fuse.
• In order to be able at any time to deal with road and traffic cnditions change, pis lower the volume when driving.
• Please do not get the device wet when washing car, this may cause sort circuit then fire or other failure wifl be caused.

WARNING

1. Only connect the unit to a DC 12V power supply with negative grounding.
2. Neyer install the unit where the operation for safety driving is restrained.
3. Never use the video display function in the front when driving to prevent the violation of law$ regulation and also to reduce the risk of traffic accident except using for rear view video camera.
4. Never expose the unit amplifier, speakers to moisture or water to prevent electronic sparks or fires.
5. Please don’t change the fuse in the power cord without professional guidance; improper fuse may cause damage to this using unit or even cause fire.

Installation

The unit installs for security, please install it refer to the following diagram description:

1. pis make the unit in proper place, connect the unit refer to the diagram, and test it works well or not
2. Pis wrapped the connection line with insulation tape to ensure complete wiring after testing well.
3. Pis bend the hook of metal 1, and insert the metal to instrument panel then fixed it
4. Put the unit into metal hook until if lock.

General Features

7″ TFT HD Touch Screen BT/FM/TF/USB MPS Rearvien Camera

• 7 inch digital TFT Touch Screen
• With TF card Slot, With USB 2.0 port.
• 1080P Video Format
• Support the Audio playback format of MP3MMAWAV/MKV/FLACIOGG/ APE.
• Support the Video playback format of RM/RMVB/DVD(VOB)/VCD(DA T)M Pl/MP2/DLVNXVLD/M P4/H263/H264/FLV /3GP / SWF/AVL/ASF/MJPEG etc;
• MOSFET amplifier: 45watts X 4 max power output
• FM Range: 87.SMHz~ 108 MHz(Europe)
• With Remote Control
• Power-off with auto-memory store function under radio or TF/USB mode
• Clock Function
• Mute Function
• BT Function
• Bass & Treble,L&R channel stabilizer
• Aux in Function
• Rearvien camera Function
• Video input Function

Specification

• SNR——————————————————————–65d8
• Frequency response————————————————-20Hz- 20KHz
• Loudspeaker impendance——————————————4-8
• The maximum output power————————————–4*45W
• Tone Control Bass————————————————–+i- 7d8(100Hz) [Treble+1 – 7d8(100Hz)]
• F M frequency——————————————————–87 .SMHz~ 108MHz
• Sensitivity ———————————————————— 2Sd8
• Selectivity ———————————————————— 60d8
• Sparation ————————————————————- 3Sd8

Bluetooth Connection Tips

1. Plug in power and turn on the car MPS player
2. Open cell phone Bluetooth, search Bluetooth device CAR – BT
3. Click CAR – BT and input password 8888 (NOTE: If 8888 was wrong, then try OOO0or 1234, or even no password); the Bluetooth mark will trun green after successfully pairing.
4. Click desktop Bluetooth and go into Bluetooth interface: Cell phone- My File-Call Records-Music

1. Plug in power and turn on the car MPS player
2. Open cell phone Bluetooth, search Bluetooth device CAR – BT
3. Click CAR – BT and input password 8888 (NOTE: If 8888 was wrong, then try OOO0or 1234, or even no password); the Bluetooth mark will trun green after successfully pairing.
4. Click desktop Bluetooth and go into Bluetooth interface: Cell phone- My File-Call Records-Music

Remote Control Description

1. Power switch
2. ◄ Right
3. Mode switch
4. Last song
5. USB/SD
6. Volume+
7. Band/Automatic/Station search
8. Digital key
9. ∧ UP
10. Menu
11. Confirm/ Play/ Pause
12. ► Left
13. ∨ Under the
14. Next song
15. Choice
16. Volume-
17. Answer the phone
18. Hang up

Front Panel

1. Last song
2. Next Song
3. Power: Press it long time to turn on/off Press it, Short time to enter into Switch mode.
4. Knob Button: Adjust VOL+NOL- ,Press it short time to enter into BASS/TRE/BAL/EQ/1 OUDNOL/BRLGHT
5. TF
6. AUX
7. RES
8. USB
9. MIC
10. JR
11. Volume+Volume-
12. Clock: Press it to adjust Date Time
13. Bright: Press it to enter into Bright mode
14. BT: Press it to enter into BT mode
15. Home
16. Radio
17. Music
18. Movie
19. Photo
20. Explore
21. Bluetooth
22. AUX in
23. Setting

HOME

Mirror Link

Please do not playback video or mobile phone while driving, it only support 4.4–8.1 android phone , other version and apple phones are not available.

1. Going to the setting, find the options of develor,ers, different phones its location is different also, some mobile phone will hidden , and need to go to “about phone” click on the version more than 5 times in a row, will appear “U have been in developer model. without having to do this” (as shown in the picture below) like below photo 1
2. Open “developer options” switch and “USB debugging” switch
3. Click “OK” Button
4. Use the original data cable to conne ct mobile phone and MPS
5. Mobile phone terminal will Pop-up window, and then click “OK” button
6. After finished the mirror link function .the function on mobile phone is available in the MPS

Above, it is operation processfor mobile phone mirrorlink. Note that each phone is different Development options are typically based on default options, and if you can’t connect, please tries the “deverloper option” and “USB debugging” options. Or please reboot the phone and reconnect to the test.

Installation Instructions

1. This product is only applicable to automobile installation with 12V power supply. If it is installed directly on the 24V vehicle or the 24V vehicle without lowering voltage, the machine will be burnt out.
2. Before install to the car, wrap the unnecessary wire, don’t expose the copper wire outside, ovoid touching the power supply or ground wire, burn out the machine and make it unable to open, no sound, etc
3. The connection must be made according to the wiring diagram. Failure to connect properly may cause machine failure or damage to the vehicle’s electrical system.
4. The horn(+,-) lead must be connected to the speaker(+,-) terminal. Do not connect the car body or interconnect the speakers.
5. Please do not plug the vent or heat dissipation plate to avoid the instability of machine performance caused by internal overheating.
6. In order to drive safely, it is recommended to set “turn ON the brake control” as “ON” in the output control of the system, then the image will be displayed only when the brake is applied, while the sound will only be output without the image, and the screen will prompt “handbrake”

Wiring Instructions

1. ACC (red line)
   ACC Ignition control power supply

2. B+ (Yellow line)
   12V Regular power supply (battery power supply)

3. GND LINE (Black)
   Ground end

4. Radio or amplifier control line (Blue line)
   For vehicles with automatic radio antenna or power amplifier and without automatic antenna,Please wrap the wire end with an insulating rubber cloth

5. Steering wheel control line (orange)
   For cars with steering wheel control, no steering wheel function, please wrap the wire with insulating tape

6. Reverse control line (Pink)
   Use when installing back-up view, do not install back-up view, wrap the wire head with insulating tape

Attention!

Please tum off the car when you are connected, and wirt! connection according to the above method, after the connection is made, wrap the joint with insulating tape. The blue line, the orange line, the pink line if you don’t use it Please wrap the wire end with insulating tape before installation, (blue line, orange Ii ne touch power will burn machine; Pink touch power will be blue screen!). Check with the volt meter ACC (Red line) , B+ (Yellow line) If there is 10V-16V voltage, the machine cannot be used normally if it is lower or higher than this voltage range.

Simple Troubleshooting

1. Don’t turn on
   • Check whether the B+ power line, ACC ignition line and GND ground line have connection or no voltage.
   • Check whether the fuse on the power seat is burned during install.and if so, replace the fuse of the same model.
2. Blue screen
   • Check whether the reversing line is connected to the power supply
   • Check whether the reversing line is connected to other functional lines.
3. No sound
   • Check whether the speaker line is properly connected
   • Check to see if only wires art! grounded, or if the two speakers are negatively connected.
   • Whether it is normal to press rt!stto rt!Set orto restort! factory Settings
   • The steering wheel without buttons should not be set in the square control Settings, if set clear restart
4. No reception
   • Check whether the radio antenna is in place.The radio antenna is whether the core wire is broken
5. Do not read the USB
6. Please format USB before copying video or music.
7. Please copy this machine support video, music, figure format
8. try to change the USS is normal
9. Don’t read the TF card
   • When copying video or music, please format the TF card first.
   • Please copy this machine support video, music, figure format
   • When trying to change TF is normal
10. There’s no reverse video
    • When checking the reverse side, the machine is turned to the reverse side interface. If the machine is not turned to the reverse side interface, the control line of the reverse side is not connected properly or correctly.
    • Check whether the camera power supply, video line and components are normal.
11. Reversing is disruptive
    • Camera flooring needs to be ground or iron bound
    • Some of the rear vehicle interference needs to be added relay or filter.
12. Touch the partial
    • Please calibration again in Settings.
13. The system did not start properly
    • Please contact after-sales or customer service staff to update the software.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>