Powr-Flite PDH2 Series Hybrid 3 Speed Carpet Dryer User Manual

Powr-Flite PDH2 Series Hybrid 3 Speed Carpet Dryer

WARNING: OPERATOR MUST READ AND UNDERSTAND THIS MANUAL COMPLETELY BEFORE OPERATING THIS EQUIPMENT.

INTRODUCTION

Check the carton for shipping damage. Carefully unpack and inspect your new Powr-Flite dryer for shipping damage. Each unit is tested and thoroughly inspected prior to shipping. If damage is discovered, immediately notify the transportation company that delivered your machine and request an inspection. As a manufacturer, we are unable to act upon any claim for concealed damage; you must originate the claim. Be sure to keep the carton, packing inserts, packing lists, and carrier’s receipt until the inspector has verified your claim.

PROTECT THE ENVIRONMENT

Please dispose of packaging materials in an environmentally safe way according to local waste disposal regulations.
Always remember to recycle

MANUAL
This manual has important information for the use and safe operation of the dryer. Read this manual carefully before starting the machine. Keep the manual available at all times and instruct all operators to read this manual.

REFERENCE INFORMATION

Reference Information
Model Number
Serial Number
Date Purchased _____
Retain this manual as a permanent record of your purchase.

SAFETY WARNINGS AND PRECAUTIONS

WARNING! Read all instructions before using. Save These Instructions. Following the cleaning instructions will prolong the life of your Powr-Flite Dryer.
When using an electrical appliance, basic precautions should always be followed.

• Use only as instructed in this manual. Use only the recommended attachments and replacement parts.
• Do not leave machine when plugged in.
• Do not leave machine connected to the electricity supply when not in use.
• Do not leave the machine unattended while running.
• Only use accessories or spares specifically designed for use with this appliance.
• The fitting of other accessories or spare parts may affect the machines performance and safety.
• Use only indoors. Do not use outdoors or expose to rain.
• If the unit is not working as it should, has been dropped, damaged, left outdoors, or exposed to water, return it to a service center before using. · Do not use with damaged cord or plug.
• Do not kink or twist the power cord.
• Do not pull or carry by the cord, use the cord as a handle, close a door on cord, or pull cord around sharp edges or corner. Keep cord away from heated surfaces.
• Do not pull on the cord to unplug. Grasp and pull the plug, not the cord. Turn off the dryer before unplugging.
• Do not handle the cord, plug, switch or dryer with wet hands.
• Do not use outlets with inadequate current capacity.
• Do not put any objects into openings. Do not use with any opening blocked. Keep free of dust, lint, hair and anything that might reduce airflow.
• Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
• Do not use near combustible liquids, gases, or dusts, such as gasoline or other fuels, lighter fluid, cleaners, oilbased paints, or natural gas, or anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
• Do not operate near draperies or another material that could block the air intakes.
• Keep air intakes clear. Reduced airflow can cause motor to overheat.
• Keep children and unauthorized persons away from the dryer when in use.
• This machine is not intended for use by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge.
• Do not attempt to service the dryer yourself. Repair by anyone other than an authorized repair service center may void the warranty. · Store in dry area.
• Do not use an extension cord with this dryer.

WARNING! To reduce the risk of fire or electric shock, do not use this fan with any solid state speed control device.

GROUNDING INSTRUCTIONS

This dryer must be grounded! Grounding is a safety measure to reduce the risk of electrical shock to the operator should the machine malfunction or stop working. Grounding provides the path of least resistance for electric current and will trip the circuit breaker, stopping the flow of electricity.

This unit is equipped with a cord that has an equipment-grounding conductor and grounding plug. The plug must be inserted in an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. Cutting off the ground wire or using a cord that is not equipped with a ground plug will void the warranty on the unit. Powr-Flite will accept NO liability associated with the unit.

WARNING! Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the appliance. If it will not fit the outlet, have a proper outlet installed by a qualified electrician.

The dryers are for use on a nominal 120-volt circuit, and have a grounded plug that looks like the plug illustrated in Figure A. A temporary adapter that looks like the adapter illustrated in Figure B and C may be used to connect this plug to a 2-pole receptacle as show in Figure B if a properly grounded outlet is not available. The temporary adapter should be used only until a properly grounded outlet (Figure A) can be installed by a qualified electrician. The green colored rigid ear, lug, or the like, extending for the adapter must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adapter is used, it must be held in place by a metal screw.

Note: In Canada, the use of a temporary adapter is not permitted by the Canadian Electrical Code.

WARNING! The replacement or repair of damaged wiring should only be performed by a qualified electrician or service engineer from the manufacturer or authorized service center.

OPERATING INSTRUCTIONS

1. Plug in to a standard outlet with the correct voltage and amperage for the unit.
2. Use only on GFCI protected recepticles.
3. Place the dryer in the desired operating position.

Daisy Chained
The PDH2 model can be daisy chained with up to 4 units on a dedicated 15 amp circuit with the built in power outlet.

WARNING! When daisy chaining units, each unit is controlled separately. The daisy chained units are not controlled by the master unit that is plugged into the wall outlet. Even with the master unit switch in the OFF position, any daisy chained unit(s) will still have power and may be turned ON.

The circuit breaker controls both the fan and the outlet. If the circuit breaker trips while units are daisy chained, remove some of the down stream units, then push in Reset button on circuit breaker. A maximum of 3 units may be daisy chained off of 1 unit for a total of 4 units per circuit.

Operating Positions

The Hybrid dryer can be used in multiple positions. The PDH1 model can be used in the vertical position (Figure 1) and the horizontal position (Figure 2). The PDH2 Deluxe model offers two additional positions. By using the kickstand (Figure 3) and side bumpers (Figure 4).

WARNING! To ensure objects are not sucked against the intake guard during operation and decrease airflow, do not place items in front of the intake guard.

3. Set the switch at the desired speed: LOW – I, MEDIUM – I I, or HIGH – III.

4. Check for proper operation before leaving the unit unattended.

WARNING! Do not move or carry the dryer when it is running.

MAINTENANCE

Routine maintenance can significantly increase the life of your Hybrid Dryer. The applications and amount of use varies, so the recommendations listed below are for average-to-high volume use. Constant operation may require additional maintenance.

WARNING! Always unplug machine before cleaning, or making any adjustments or repairs.

Before Each Use

1. Inspect power cord for fraying, cuts or damage; do not use if damaged.
2. Remove lint or obstructions from the Intake Guard and Exhaust Port Guard using a vacuum or compressed air.
3. Inspect exterior components (switch, knob, etc.) for damage.

After Each Use

1. Remove any lint or debris from the intake screen.
2. Clean dust and dirt from motor using a vacuum or compressed air.
3. Snugly wrap the power cord around the cord wrap/feet and secure the end of the power cord to itself using the latch on the plug of the power cord.
4. Clean the exterior with a household all-purpose spray cleaner. Spray the rag, then apply to the surface.

Periodic Maintenance

1. Inspect all electrical connections.
2. Check the power cord for any breaks, fraying, separations, or cuts.
3. Make sure the ground pin or grounding prong is intact.
4. Inspect the motor and fan for build-up of debris, removing the intake screen and fan, cleaning as required.

TROUBLE SHOOTING

If the dryer will not turn on:

1. Make sure the power cord is firmly connected to the unit and is in good condition.
2. Make sure the power cord is firmly seated in the wall outlet.
3. If using an extension cord, make sure it is in good condition, proper gauge and firmly connected.
4. Check to see if the building circuit breaker is tripped. If circuit is overloaded, move the unit to another circuit. On PDH2 – check circuit breaker on unit.

STORAGE

Always store the dryer in a dry place. The dryers can be stacked during storage or transport to minimize the required space. The stacking guide is located on the top and bottom of each unit.

SPECIFICATIONS

Specifications and parts are subject to change without notice.
Please refer towww.Powr-Flite.com for the latest schematic drawing and parts list.

56 cm x 42 cm x 29 cm

ITEM

| Schematic and PartS list DESCRIPTION| PART NO.|

OTY

---|---|---|---
1| SWITCH LABEL| X9728| 1
2| DRYER KNOB| X9831| 1
3| VINYL CAP| X9731| 4
4| WARNING LABEL| X9727| 1
5| SWITCH MOUNTING SCREW| X8903| 2
6| 8-32 X 1/2″ GRILL SCREW| X8278| 2
7| HOUSING, TOP| X9701| 1
8| FRONT LABEL| X9726| 1
9| 8-32 NYLON LOCNUT| X8260| 2
10| CORD 14GA 3 CONDUCTOR 20FT| X1002| 1
11| SWITCH| X8897| 1
12| FAN BLADE| X1023| 1
13| 1/4-20 X 2.75″ BOLT| X9702| 5
14| 1/4″ FLAT WASHER| X8235| 5
15| RUBBER GROMMET| X9705| 1
16| CABLE P-CLIP| 04-0286-0000| 1
17| LABEL, SERIAL NUMBER, PLAIN| X8459| 1
18| LABEL, WARNING| X8976| 1
19| 8-18 HI-LO .5″ LONG| X9690| 3
20| 8-18 3/4 LONG HI LO SCREW| X9676| 10
21| 1/4-20 NYLOC| X8237| 5
22| DRYER DISCHARGE GRILL| X8871| 1
23| HYBRID DRYER MOTOR| X9674-120| 1
24| HOUSING, BOTTOM| X9700| 1
25| GRILL MOUNTING RIVOT| X8946| 2
26| FOOT, BLACK, RUBBER,TALL (Qty of (4) PDH2 ONLY)| PD3B| 2
27| HYBRID FOOT SCREW| X9704| 2
28| NUT 8-32 KEPS ZINC| X8256| 2
29| SCREW, #8-32 X 1/2″L, PNHD, PH, ZP| PX73| 2
30| KICKSTAND, DRYER (PDH2 ONLY)| X8874| 1
31| LEFT FOOT, DRYER KICKSTAND (PDH2 ONLY)| X8929| 1
32| KICKSTAND SCREW (PDH2 ONLY)| X8261| 4
33| RIGHT FOOT KICKSTAND HINGE (PDH2 ONLY)| X8928| 1
34| 9AMP CIRCUIT BREAKER (PDH2 ONLY)| X1022| 1
35| WIRING HARNESS WITH POWER OUTLET| X9757| 1
36| MADE IN THE USA LABEL| X1004| 1

For warranty information go towww.Powr-Flite.com

A Tacony Company
3101 Wichita Court · Fort Worth, TX 76140-1755
1-800-880-2913 · Fax: 1-817-551-0719

References

• Commercial Floor Care Equipment | Powr-Flite

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>