Armacost 723422 Slimline LED Wireless Remote Controller User Guide

June 6, 2024
Armacost

Armacost 723422 Slimline LED Wireless Remote Controller User Guide
Armacost 723422 Slimline LED Wireless Remote
Controller

Model # 723422

Content

Introduction

This LED controller is designed to drive constant voltage RGB+White LED products such as LED tape light or LED fixtures in a voltage range of 5–24 volts DC. The receiver works with the RF wireless remote control, which allows the user to choose between multiple colors, adjust the LED brightness, and select dynamic effects.

Receiver & wiring

Wiring diagram

  1. Input – from power supply
    The controller input and output voltage range is 5–24 volts DC. Make sure the LED lighting voltage is within this range and below the rated wattage of the power supply. Connect input wires from the power supply to the controller as indicated by the polarity markings on the controller (+ to + and – to –).

  2. Output – to LED lighting
    Observe polarity indicated on the controller when connecting to LED lighting (+ to +, G to G, R to R, B to B, and W to W). Make sure the voltage of the LED lighting is the same as the power supply and the maximum load doesn’t exceed that of the controller. CAUTION: Shorting of output cables could cause permanent damage to controller. Make sure cables are well insulated from each other.

  3. Wiring diagram
    Connect the power supply to the controller input and the controller output to the LED lighting. The output voltage of the power supply must be the same as the voltage of the LED lighting. Make sure all power cables are connected securely and insulated before powering on.
    Wiring diagram

Remote Control

Remote Control

  1. On / Off
    Press the “|” key to turn on controller or the “0” key to turn off. The controller will remember the controller state when powered off, and will return to that state when powered back on.

  2. Mode selection
    Press this key to switch between RGB, white, and RGB+white mode. If the RGB mode is selected, the white channel will be disabled, and if the white mode is selected, RGB channel will be disabled. In RGB+White mode all channels are enabled.

  3. Select static RGB color
    Press the “COLOR+” and “COLOR–” keys to scroll through the preset library of colors.

  4. Shortcut color keys
    Press to select preset colors.

  5. White brightness control
    Press to increase white LED brightness and press to decrease it.

  6. RGB brightness control
    Press to increase RGB LED brightness and press to decrease it.

  7. Dynamic effect
    Press “FX ” and “FX ” to select the dynamic effect mode and “FX SPEED ” and “FX SPEED ” to adjust the effect speed.

  8. Remote indicator
    When pressing keys, the indicator blinks if the remote is working properly. If the indicator flashes slowly when pressing keys, battery power is low and it needs to be replaced. Replace with a CR2032 battery

Remote control operation

  1. Using the remote control
    Pull out plastic battery insulation tab before use. The RF wireless remote will work through walls and doors. Do not install in a metal enclosure.

  2. Pairing with a new remote control The remote control and receiver are already paired, but up to 5 remotes can be paired to one receiver.
    To pair a new remote:

  3. Disconnect power to receiver and wait five seconds.

  4. Reconnect power and wait ten seconds.

  5. Press the and  keys simultaneously for about three seconds until the remote indicator flashes quickly.

  6. De-pairing remotes
    To de-pair a remote control, pair the remote you wish to continue using with the controller and any other paired remotes will be de-paired.

Overheat protection

If the controller overheats, it will automatically shut down until the temperature drops to a safe range. If this occurs, check to make sure the output current is below the rated level.

Specifications

  • Output mode: PWM constant voltage
  • Working voltage: 5–24V DC
  • Rated output current: 4x2A (8A max)
  • Static colors: 30
  • White brightness levels: 10
  • Color brightness levels: 5
  • Dynamic effects: 42
  • Dynamic speed levels: 10
  • Color preset keys: 7
  • PWM frequency: 1KHz
  • PWM physical grade: 4000 steps
  • Overheat protection: Yes
  • Remote frequency: 433.92MHz
  • Remote control range: >49 ft./15m in open areas
  • Controller dimensions: 197 X 0.59 X 0.28 in. 50 X 15 X 7mm
  • Remote dimensions: 3.41 X 1.42 X 0.329 in./ 86.5 X 36 X 7.5mm

Customer support

Email: support@armacostlighting.com
Phone: 410-354-6000
Monday–Friday, 9 a.m.–5 p.m., ET

Warranty

1-year limited warranty. This product is for dry location use only. Improper installation, improper powering, abuse, or failure to use this device for its intended purpose will void warranty. Proof of purchase is required for all returns. Questions? Email support@armacostlighting.com.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Armacost User Manuals

Related Manuals