psb SPEAKERS M4U8 MKII Wireless ANC Headphone Owner’s Manual
- June 6, 2024
- psb SPEAKERS
Table of Contents
M4U8MKII
WIRELESS ACTIVE NOISE
CANCELLING HD HEADPHONES
OWNER’S MANUAL
INTRODUCTION
Thank you for purchasing a pair of PSB Speakers M4U 8 MKII Headphones.
Producing natural musical dynamics and precisely imaged sound, these high-
fidelity headphones bring you closer to the music you love.
Engineered with 50 years of audio excellence and research, the M4U 8 MKII
delivers unmatched sound quality, all-day comfort, and fold-and-go
portability, for music enthusiasts and professionals. PSB’s true-to-nature
sound quality and stylish ergonomic design allow you to escape to a personal
concert experience that travels anywhere with you.
REGULATORY INFORMATION
Operating Temperature Range:
Operating Frequency Range:
Max Output Power:
Input
Rating:
Battery
Rating:
Battery Charging Time:
Weight:| 5°C – 40°C
Bluetooth 2.4G
5.5mW
5VDC,
1A
1.2V,
1000mAh
4 hours
332grams
---|---
Is in compliance with the essential requirements and other relevant provisions
of Directive 2014/53/EU.
Date of Manufacture: The second and third digits in the serial number indicate
the year of manufacture; “21” is 2021.
Responsible Party: Lenbrook Industries Limited. 633 Granite Court, Pickering,
Ontario, Canada L1W 3K1. Phone: (905) 8316333, Facsimile:
905-831-6936
The Bluetooth® word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc., and any use of such marks by PSB Speakers is under
license.
The N-Mark is a trademark or registered trademark of the NFC Forum, Inc. in
the United States and in other countries
To prevent possible hearing damage, do not listen to high volume levels for
long periods.
OSHA Guidelines for Noise Exposure Limits
The Occupational Safety Health Administration (OSHA) has issued headphone
usage recommendations for maximum daily exposure and sound pressure levels
[measured in decibels (dB)]. A decibel is a unit of sound measurement that
increases exponentially with volume. For example, conversational speech is
typically around 60dB, and a rock concert in a stadium is often about 110dB.
90dB | 8 hours |
---|---|
95dB | 4 hours |
100dB | 2 hours |
105dB | 1 Hour |
110dB | 30 minutes |
115dB | 15 minutes |
120dB | Avoid as damage may occur |
SAFETY INFORMATION
Please read this booklet to ensure that you are getting the most out of your
PSB product and music.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC ID: SVC-PSBM4U8MKII
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Radio Frequency Exposure Statement for IC
The device has been evaluated to meet general RF exposure requirements. The
device can be used in mobile exposure conditions. The min separation distance
is 25mm.
WARNING
- Warnings or announcements may be unnoticed when you are using the headphones. Please be aware of ambient sounds while wearing the headphones and recognize them as needed.
- To prevent possible hearing damage, do not listen to high volume levels for long periods.
- These headphones should only be connected to a USB interface of version USB2.0 or higher.
- Risk of explosion if the battery is replaced by an incorrect type, dispose of used batteries according to the instructions.
- Be sure to read the Owner’s Manual of the device that you want to connect to these headphones.
- Check the volume settings when using the headphones when in public places and ensure that you do not disturb people around you.
- These headphones are not guaranteed to work with all combinations of Bluetooth devices/mobile phones.
- These headphones do not support a connection with all Bluetooth devices/mobile phones.
- Bluetooth wireless technology can communicate up to approximately 10 m. Obstructions (people, metallic objects, walls, etc.) and radio wave conditions affect the actual range.
- The Bluetooth device that you want to connect with must support the same profile as these headphones in order to use the Bluetooth function. For details on profiles that the Bluetooth device is compatible with, see the Bluetooth device Owner’s Manual.
- Due to the features of Bluetooth wireless technology, the playback of audio on the headphones is slightly delayed compared to the playback on the transmitting device.
- Do not use your headphones while driving.
- Remove the headphones immediately if you experience a warming sensation or loss of audio.
- Do not use mobile phone adaptors to connect these headphones to airplane seat jacks, as this could cause overheating and result in injury or property damage.
- The headphones and accessories contain small parts which may be a choking hazard. Not suitable for children under age 3.
- This product contains magnetic material. Consult your physician on whether this might affect your implanted medical device
- Use this product only with an agency approved power supply that meets local regulatory requirements (e.g., UL, CSA, VDE, CCC).
- Do not expose products containing batteries to excessive heat (e.g. from storage in direct sunlight, fire, or the like).
- Long-term exposure to loud music may cause permanent hearing damage. To avoid personal injury when using the headphones for extended periods, the volume should be kept at the described levels in Figure 1.
- Fire or shock may occur should water or other foreign substances permeate inside the device.
- Do not attempt to modify this product as it could result in personal injury and/or product failure.
- Keep batteries out of reach of children
CONNECTING
Wired Connections
Before connecting your headphones, ensure your audio source is powered off, as
severe damage to equipment and/or your ears could result.
To connect your headphones, plug the 1/8-inch (3.5mm) straight connector into
one of the inputs located at the base of the left (L) or right (R) ear cup.
This allows you to pick a preferred side for a more comfortable listening
setup as shown in Figure 2.
Figure 2
If your audio equipment uses a 1/4-inch (6.3mm) output jack, use the included
1/4-inch adaptor.
USB Cable
Use the supplied USB cable to listen to music from your computer (audio only).
This cable is used to charge your M4U 8 MKII headphones.
Notes:
Use the supplied USB cable to listen to music from your computer (audio only).
This cable is used to charge your M4U 8 MKII headphones.
EARPHONE MOUNTED CONTROLS…
The main controls are located on the rear part of the right ear cup. They are
used to control Volume, Noise Cancelling, and your smart device (tablet, iPod)
as needed.
The Controls are used as follows:
Volume and Active Monitor
Slide up towards the + sign to increase the volume.
Slide down towards the – sign to lower the volume.
Press the button VOL to engage the Transparency Mode and reduce your current
audio track by 30dB. This will enable you to hear your surroundings, without
leaving your personal space. The described function only works in powered
modes. When activated, the surroundings will be amplified through the
headphones.
Active Noise Cancellation and Amplifier
The power modes use internal (rechargeable) batteries.
In Active Noise Cancelling mode, the “Noise Cancelling” feature has been
activated with the internal headphone amplifier. The 3-position Power Switch
will be “GREEN”.
In Active mode, the internal headphone amplifier is active. The 3-position
Power Switch will be “BLUE”.
In Passive mode (OFF), noise-canceling and amplifier are turned off. No power
is required as the headphones are powered by your audio source.
NOTE: Bluetooth connection will not work in this mode.
Phone Function
If you receive a phone call during a listening session press the phone button
to answer the incoming call and pause your audio track. Once the call is
complete, a single button press will end the call and resume audio play.
To activate Siri or Google Assistant, hold down the phone button for five
seconds.
When listening to a handheld music device, this button can be used to change
to the previous track, the next track, or pause and resume music without
reverting to the controls of the handheld device.
Slide the button up for the previous track.
Slide the button down for the next track.
NOTE: Phone function only works when connected by Bluetooth.
Wireless Pairing
Pairing is the process required to create a link between Bluetooth devices to
allow wireless connection. You must pair a device with the PSB M4U 8 MKII to
be able to make a BLUETOOTH connection for the first time.
Before you start pairing operation, make sure that:
The Bluetooth device is placed within 1 m (3 feet) of the headset.
The M4U 8 MKII is charged sufficiently.
To pair your device:
- Turn on the Bluetooth feature on your source device.
- Open the Bluetooth settings on the source device.
- Switch the M4U 8 MKII into a powered mode. The pairing LED will flash RED and BLUE.
- Select your M4U 8 MKII headphones from the device list.
- Once the M4U 8 MKII’s link has been established with the source device, the pairing LED will turn solid BLUE.
- If pairing fails, the pairing LED will turn solid RED.
NFC Wireless Pairing
M4U 8 MKII supports Near Field Communication (NFC) so you can easily pair your
headphones. For pairing follow the instructions below.
To pair your device using NFC:
- Turn on NFC and Bluetooth on the device you are pairing.
- With the M4U 8, MKII turned on in one of the powered modes, place your Bluetooth-enabled device against the opposite side of the right ear cup where the controls are located.
- Accept the pairing on your device when prompted.
Note: NFC is a short-range wireless communication. Pairing devices are required to be within a few centimeters of the headphones to communicate. If pairing is unsuccessful, refer to the device’s manual to find its NFC touchpoint. Repeat the steps shown and ensure the located touchpoint is placed against the right ear cup as directed in Step 2.
Bottom Right
Top Right
LISTENING…
With the volume set to low, turn on your audio source, find a comfortable
listening level, and drift into a personal space filled with the sounds of
your favorite audio/video collections.
Headphone Placement
Each ear cup is marked with “L” and “R” to indicate the left and right sides
of the headphones. Be sure to put them on correctly to enjoy your audio as
originally intended and maximize your personal music experience.
PERSONAL SOUND…
Audio Personal Sound is a unique feature that corrects your own personal
hearing.
You must download the PSB Headphones app for your device in order to calibrate
your headphones with Audio do. Personal Sound calibration will not be possible
without the PSB Headphones app.
http://www.psbspeakers.com /headphones-app
Once you have the PSB Headphones app downloaded and your M4U 8 MKII paired to
that device, you are ready to set up your Audio do profile.
In the PSB Headphones app…
Tap the “To Calibration” button to begin the hearing calibration.
The hearing calibration is meant to assess your hearing characteristics. To
produce the most accurate results, we advise you to complete the calibration
in a quiet place; the quieter, the better. If you’re unsure whether you hear a
tone or not, it is best to select NO.
The calibration will begin when you tap the Start Calibration button.
The hearing calibration has now commenced, and you can select YES if you hear
a tone or NO if you do not. If you feel you cannot hear any tones during the
calibration, please make sure that you are connected to the headphones.
To quit the hearing calibration, tap the X in the top-right corner. If you
choose to quit you will be redirected to the start page. You can redo the
calibration at a later time, but no data will be saved.
After completing the hearing calibration, you can name your profile. The name
must be at least one character long. You must create a name to proceed.
To update/rename your profile, select Profiles from the main menu, then the
dropdown menu beside your profile.
Please select the icon that best describes your gender. Since gender affects
how we hear, it’s beneficial for us to collect this information in order to
optimize the test process and the algorithms behind Audio do Personal Sound.
You must select an icon to proceed. If you wish to decline to answer, choose
the icon in the middle. This information is not used for marketing purposes.
Please select your age by dragging the cursor. Age affects how we hear, so
it’s beneficial for us to collect this information in order to optimize the
test process and the algorithms behind Audio do Personal Sound. You must
select an age to proceed. This information is not used for marketing purposes.
Tapping the menu icon in the top-left corner will take you to the main menu.
The top-right corner will take you to the Profiles list.
To toggle the Personal Sound ON/OFF, tap the yellow button in the center next
to the text Personal Sound.
On your visual hearing profile., the x-axis represents sound pressure levels
while the y-axis represents frequencies. Where the curves dip lowest, is where
the algorithm will compensate most.
To redo the hearing calibration or to add a new profile, tap the + in the top-
left corner. This will take you to the screen where you can complete a new
hearing calibration.
Multiple profiles can be stored on the app. To update/rename your profile,
select the dropdown menu beside your profile. If you happen to connect the
application to headphones that already have a profile stored on them, you will
see the Profile mismatch message. This means that a profile exists on the
headphones you are now using but not on the app. To download/save the profile
that is on headphones to your mobile application, select YES. If you select No
the profile will not be downloaded to the app and cannot be accessed again
unless the previous app and headphones are paired again.
If for some reason your device gets disconnected, select TRY AGAIN to
reconnect to it. To connect to a different device, select ADD HEADPHONES.
CONNECTING TO IN-FLIGHT ENTERTAINMENT SYSTEMS…
To connect to in-flight entertainment systems equipped with dual output
connectors, use the supplied dual 3.5mm airline adaptor and the standard
analog cable.
NOTE:
-
Audio output jack configurations may vary on airplanes. Airline audio quality may not equal what your home audio
equipment or portable sources provide. -
The supplied conversion plug may not be usable depending on the type of aircraft.
-
Do not use these headphones when the use of electric devices on the aircraft is prohibited, or when the use of personal headphones to listen to on-board music service is prohibited.
WARNING
PSB Speakers recommends you do not use these headphones as aviation communication equipment. They are not engineered for many environmental conditions common in commercial or non-commercial aircraft (including, but not limited to: altitude, temperature, noise conditions, unpressurized aircraft) and could result in possible interference to critical communications.
WARNING
Liquids or cleaning solvents can cause irreparable damage to the electronics inside your headphones. The M4U warranty does not cover such damage.
M4U 8 HEADPHONE CARE
For safe, sanitary use, it is essential to maintain and clean your M4U
Headphones periodically. However, excessive cleaning may cause damage and
jeopardize the longevity of the product. When not in use, always store
headphones in the supplied protective case, and store them in a clean and dry
environment. Avoid storing in extreme heat or cold temperatures and humidity,
and avoid exposure to liquids.
Cleaning…
For regular cleaning, use a slightly damp cloth and gently clean each ear cup
cushion, then use a dry cloth to remove any residual moisture.
If heavy cleaning is necessary after extended listening and use, follow these directions:
- Remove the earcup cushions according to the Cushion Attachment/Detachment instruction section following.
- Clean the earcup cushions by hand, using cold water.
- Add a very small amount of dish or laundry soap and gently clean the cushions.
- After cleaning the cushions, rinse with clean water.
- To dry the earcup cushions, place them on a towel with the pads facing up.
- Fold the towel over the top of the cushions and press down to remove any excess water in the foam padding.
- Air-dry completely before reattaching.
Cushion Attachment/Detachment
-
To detach the earcup cushion, grasp the headband over the ear cup cushion that needs to be removed.
-
Using your other hand, grip the leather ear cup cushion and carefully stretch and pull the earpad away from the ear cup. Repeat on the other earcup if necessary.
-
To reattach the earcup cushion, grip the headband and cushion as described above, and clip the lip of the earcup cushion back in place. The right side should be installed back on the ear cup with the controls.
NOTE: -
Be careful not to press down on or remove any other components inside the earcup as this could damage the headphones.
Storage in the protective case
1. Remove the cable from the headphones, fold and insert them into the
protective case. NOTE:
- Do not force them into the protective case. Doing so may damage the headphones.
WARNING
When disconnecting your M4U Headphones, hold the plug at the end of the cable and pull to disconnect. Do not pull on the headphone cable to disconnect the headphones from your music player.
PROTECTING YOUR INVESTMENT….
For long-lasting enjoyment of your headphones, you should respect their limits
and avoid excessive volume levels for music or movie playback. Excessive
volume levels can damage all headphones.
If your headphones are pushed to excessive volume levels, they could be driven
into “clipping”. This could result in severe or permanent injury. When using
your headphones at loud levels, listen carefully for any sign of harsh,
garbled midrange and diminishing intelligibility. If detected, turn the volume
down immediately.
NEVER TEST PEAK LISTENING LEVELS OF THE HEADPHONES BY TURNING THE VOLUME UP
ALL THE WAY!
At the end of its useful life, this product should not be disposed of with
regular household waste. It should be returned to a collection point for the
recycling of electrical and electronic equipment.
The materials can be reused in accordance with their markings. Through re-use,
recycling of raw materials, or other forms of recycling of old products, you
are making an important contribution to the protection of our environment. The
following symbols on the packaging indicate the recycling mandate.
Your local administrative office can advise you of the responsible waste disposal location.
PSB and the PSB logo are trademarks of PSB Speakers, a division of Lenbrook Industries Limited. All rights reserved. No part of this publication may be reproduced, stored, or transmitted in any form whatsoever without the written permission of PSB Speakers. While every effort has been made to ensure the contents are accurate at the time of publication, features and specifications may be subject to change without prior notice. 20-042 © 2021 PSB Speakers. Designed in Canada, Made in China www.psbspeakers.com