psb SPEAKERS Synchrony T600 Loudspeaker Owner’s Manual

June 10, 2024
psb SPEAKERS

SYNCHRONY
SYNCHRONY Series Owner’s Manual

Introduction

Congratulations for purchasing a member of the PSB Synchrony Series. Synchrony represents the finest application of PSB’s design philosophy which has been refined over nearly 50 years.
In order to assist in the enjoyment your speakers, we have provided you with some instructions for assembly, and some suggestions to help you optimise their performance.
Additional information may be found on our website: www.PSBspeakers.com

Port Cover (Figure 1)
Two Port Covers are supplied with each tower. The port cover can be used to adjust the bass tuning of the Synchrony towers where room problems at low frequencies (in the 1OOHz region) occur. It is well known that the room can dominate the performance of the low frequencies below 200Hz and the added flexibility of a port cover can tweak/improve the performance in problem room setups.
We invite the listener to try plugging any one or multiple ports to better integrate the system in their room because any adjustment of the bass balance could be a welcome improvement in a given system setup. Please experiment; it will be worth the effort in many cases. It is impossible to predict what type of room or what the system setup will be, therefore we think the flexibility of multiple ports allows the speaker to be integrated better in a wider variety of situations. Sometimes tweaking like this can be used to really help “dial in” the best possible sound in your room.

Speaker Terminal Jumper Bars (Figure 2 / 3)
The Synchrony towers also include two speaker terminal jumper bars. This will provide listeners with tri- and bi-wiring capabilities, as well as tri- and bi-amping. Though the audible differences of these features may be subtle, the benefits include; transients are less likely to cause clipping and/or speaker damage, reduced distortion and the elimination of errors at low frequencies, while also providing better matching between the power amplifier and speaker.

|
---|---

Installation of IsoAcoustics (Figure 4)
The Synchrony towers are furnished with GAIA II isolators by IsoAcoustics’, to provide a high degree of speaker isolation, while resisting lateral movement.
Note: The isolators are directional, make sure to install the GAIA’s with the logo facing forward.

  1. Carefully lay the speaker down on its side on a soft-padded surface to avoid scratching or damaging the cabinet.
  2. Install each of the GAIA isolators through the base of the speaker, leaving no more than 6mm between the isolator and the underside.
  3. Carefully stand the speaker upright on the floor.
  4. Do not slide the speakers on the floor. Lift the speakers and lower them to the final position, or tilt the speaker and position a cloth or furniture sliders underneath the isolators to allow them to slide on the floor. Remove the furniture sliders or cloth once the speakers are in the final position.
  5. Once in position, level the speaker by adjusting the height of the GAIA isolators. When making adjustments, tilt the speaker so that the isolators are raised above the floor, then rotate the GAIA isolators to adjust their height.
  6. Tilt the speaker and rotate the GAIA’s so that each isolator has the IsoAcoustics logo facing forward.
  7. Finish by firmly installing the threaded caps on the top of the studs.

Custom isolators (Figure 5)
The Synchrony B600 are equipped with custom isolators from IsoAcoustics which are integrated into the base of each speaker.

Specifications

Specifications B600 T600 T800

Frequency Response
On Axis @0 +/- 3db      On axis @0 +/- 1 1/2db     off Axis @ 30 =/- 1
1/2db  LF Cutoff| 50-23,000Hz
55-20,000Hz
55-10,000Hz
35Hz| 24-23,000Hz
30-20,000Hz
30-10,000Hz
20Hz|  21-23,000Hz
24-20,000Hz
30-10,000Hz
20Hz
Sensitivity
Anechoic
Listening Room| 86dB
88dB| 89dB
91dB| 89dB
91dB
Impedance
Nominal
Minimal| 6 Ohms
4 Ohms| 4 Ohms
4 Ohms| 4 Ohms
4 Ohms
Input Power
Recommended
Program| 15-150 Watts
150 Watts| 20-300 Watts
300 Watts| 20-300 Watts
300 Watts
Acoustic Design
Tweeter| 1” (25mm)
Titanium Dome with
Ferrofluid|  1” (25mm)
Titanium Dome
with Ferrofluid|  1” (25mm)
Titanium Dome
with Ferrofluid
Midrange| | 5 1/4” (133mm)
Cast Basket
Carbon Fibre Cone
Rubber Surround|  5 1/4” (133mm)
Cast Basket
Carbon Fibre Cone
Rubber Surround
Woofer| 6 1/2” (165mm)
Cast Basket
Carbon Fibre Cone
Rubber Surround| 3 x 6 1/2” (165mm)
Cast Basket
Carbon Fibre Cone
Rubber Surround| 3 x 8” (203mm)
Cast Basket
Carbon Fibre Cone
Rubber Surround
Crossover| 2,200Hz, L4| 450Hz B3, 1800Hz LR4| 450Hz B3, 1800Hz LR4
Design Type| 2-way system
Bass Reflex,
Rear facing port| Transitional 3-way system
Bass Reflex,
Triple Rear facing ports
3 Individual Woofer chambers| Transitional 3-way system
Bass Reflex,
Triple Rear facing ports
3 Individual Woofer chambers
Dimensions
Size ( WxHxD)| 9 x 15 1/2 x 11 1/2”
228 x 393 x 298mm| 9 x 41 1/4 x 13 1/2”
228 x 1048 x 343mm| 14 7/8 x 47 3/4 x 15 5/8”
377 x 1212 x 396mm
Net Weight| 23 lbs
10.4 kg| 77 lbs
34.9 kg| 100 lbs
45.36 kg
Finish| Walnut
High Gloss Black| Walnut
High Gloss Black| Walnut
High Gloss Black
Features| Dual, 5-way, Gold-plated
Binding Posts,
Bi-wireable/Bi-ampable,        Magnetic Grille
isoAcoustic isolation Feet
Rear Facing Port| Triple, 5-way
Gold-plated Binding Posts
Tri-wireable/Tri-ampable,
Magnetic Grille Outrigger stabilizers with
isoAcoustic GAIA II feet
Port Plug (x2)
Subdivided discrete Chambers
3 Individual Woofer Chambers
Triple Rear Facing Ports| Triple, 5-way
Gold-plated Binding Posts
Tri-wireable/Tri-ampable,
Magnetic Grille
Outrigger stabilizers with
isoAcoustic GAIA II feet
Port Plug (x2) Subdivided discrete
Chambers 3 Individual Woofer
Chambers Triple Rear Facing Ports

PSB Speakers
633 Granite Court Pickering, Ontario. L1W 3K1 CANADA
www.psbspeakers.com 888-772-0000 905-831-6555 Fax: 905-831-6936

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals