Intel NUC Kit NUC10i7FNK User Manual

: June 2, 2024
: Intel

Intel® NUC Kit NUC10i7FNK

Intel® NUC Kit NUC10i5FNK

Intel® NUC Kit NUC10i3FNK

User Manual

Intel® NUC Kit NUC10i7FNK Intel® NUC Kit NUC10i5FNK Intel® NUC Kit
NUC10i3FNK User Manual

Before You Begin

CAUTIONS

The steps in this guide assume you’re familiar with computer terminology and with the safety practices and regulatory compliance required for using and modifying computer equipment.

Disconnect the computer from its power source and from any network before performing any of the steps described in this guide.

__

Failure to disconnect power, telecommunications links, or networks before you open the computer or perform any procedures can result in personal injury or equipment damage. Some circuitry on the board can continue to operate even though the front panel power button is off.

Follow these guidelines before you begin:

Always follow the steps in each procedure in the correct
Create a log to record information about your computer, such as model, serial numbers, installed options, and configuration
Electrostatic discharge (ESD) can damage Perform the procedures described in this chapter only at an ESD workstation using an antistatic wrist strap and a conductive foam pad. If such a station isn’t available, you can provide some ESD protection by wearing an antistatic wrist strap and attaching it to a metal part of the computer chassis.

Installation Precautions

When you install and test the Intel NUC, observe all warnings and cautions in the installation instructions.

To avoid injury, be careful of:

Sharp pins on connectors
Sharp pins on circuit boards
Rough edges and sharp corners on the chassis
Hot components (such as SSDs, processors, voltage regulators, and heat sinks)
Damage to wires that could cause a short circuit

Observe all warnings and cautions that instruct you to refer computer servicing to qualified technical personnel.

Observe Safety and Regulatory Requirements

If you don’t follow these instructions, you increase your safety risk and the possibility of noncompliance with regional laws and regulations.

This guide tells you how to:

Install and remove memory
Install an 2 SSD
Install a VESA mount bracket
Connect power
Install an operating system
Install the latest drivers

Open the Chassis

Unscrew the four corner screws on the bottom of the chassis and lift the cover.

Intel, NUC Kit, NUC10i7FNK Open the Chassis

Installing and Removing Memory

Intel NUC Kits NUC10i7FNK, NUC10i5FNK and NUC10i3FNK have two 260-pin DDR4 SO- DIMM sockets. Memory requirements:

2V low voltage memory
2666 MHz SO-DIMMs
Non-ECC

Find compatible memory modules in the Intel Product Compatibility Tool

NOTE: If you plan to install only one memory module, install it in the lower memory socket.

Install SO-DIMMs

If you plan to install just one SO-DIMM, install it in the lower memory socket.

To install the SO-DIMMs, follow these steps:

Observe the precautions in “Before You Begin” on page
Turn off all peripheral devices connected to the Turn off the computer and disconnect the AC power cord.

Intel, NUC Kit, NUC10i7FNK Install SO-DIMMs

Align the small notch at the bottom edge of the SO-DIMM with the key in the
Insert the bottom edge of the SO-DIMM into the
When the SO-DIMM is inserted, push down on the outer edge of the SO-DIMM until the retaining clips snap into Make sure the clips are firmly in place.

Removing SO-DIMMs

To remove a SO-DIMM, follow these steps:

Observe the precautions in “Before You Begin” on page
Turn off all peripheral devices connected to the Turn off the computer.
Remove the AC power cord from the
Remove the computer’s
Gently spread the retaining clips at each end of the SO-DIMM The SO-DIMM pops out of the socket.
Hold the SO-DIMM by the edges, lift it away from the socket, and store it in an anti-static
Reinstall and reconnect any parts you removed or disconnected to reach the SO-DIMM
Replace the computer’s cover and reconnect the AC power

Install an M.2 SSD

Intel NUC Kits NUC10i7FNK, NUC10i5FNK and NUC10i3FNK support 80mm and 42mm SSDs. Find compatible M.2 SSDs at the Intel® Product Compatibility Tool:

NOTE: Before changing the Intel Optane memory module, it needs to be disabled. Follow Removing Intel Optane Memory on this page first, before taking the module out.

If you’re installing an 80mm M.2 SSD:

Remove the small silver screw from the 80mm (A) and 42mm (B) metal standoff on the
Align the small notch at the bottom edge of the 2 card with the key in the connector.
Insert the bottom edge of the 2 card into the connector (C).
Secure the card to the standoff with the small silver screw (D).

Intel NUC Kit NUC10i7FNK installing an 80mm M.2 SSD

If you’re installing a 42mm M.2 SSD:

Remove the small silver screw from the metal standoff on the motherboard (A).
Align the small notch at the bottom edge of the 2 card with the key in the connector.
Insert the bottom edge of the 2 card into the connector (B).
Secure the card to the standoff with the small silver screw (C).

Intel NUC Kit NUC10i7FNK installing a 42mm M.2 SSD

Close the Chassis

After all components have been installed, close the Intel NUC chassis. Intel recommends this be done by hand with a screwdriver to avoid over-tightening and possibly damaging the screws.Intel NUC Kit NUC10i7FNK Close the Chassis

Attach and Use the VESA Bracket (Optional)

Follow these instructions to attach and use the VESA mount bracket:

Using the four small black screws that were included in the box, attach the VESA bracket to the back of the monitor or TV.

Intel NUC Kit NUC10i7FNK Using the four small black
screws

Attach the two slightly larger black screws to the bottom chassis cover of the Intel NUC.
Slide the Intel NUC onto the VESA mount

Intel NUC Kit NUC10i7FNK Slide the Intel NUC onto the VESA mount
bracket

Connect Power

Country-specific power cords are included in the Intel NUC Kit box.

Connect AC power

Intel NUC Kit NUC10i7FNK Connect AC power

Each Intel NUC model includes either a region-specific AC power cord or no AC power cord (only the power adapter).

Product codes	Power cord type
BXNUC10i7FNK, BXNUC10i5FNK, BXNUC10i3FNK	No power cord included. An AC power

cord needs to be purchased separately. Power cords are available at many Internet sites for use in multiple countries. The connector on the power adapter is a C5 type connector.

BXNUC10i7FNK1,

BXNUC10i5FNK1, BXNUC10i3FNK1

| US power cord included.
BXNUC10i7FNK2 BXNUC10i7FNKPA2, BXNUC10i5FNK2, BXNUC10i5FNKPA2,

BXNUC10i3FNK2

| EU power cord included.
BXNUC10i5FNK3,

BXNUC10i5FNKPA3 BXNUC10i3FNK3

| UK power cord included.
BXNUC10i5FNK4,

BXNUC10i3FNK4

| Australia/New Zealand power cord included.
BXNUC10i7FNKP6

BXNUC10i5FNKP6

| China power cord included.

Install an Operating System

Refer to Supported Operating Systems for a list of Intel-validated Windows* operating systems and versions of Linux that have been reported as compatible by Intel NUC owners.

Refer to Operating System Installation for system requirements and installation steps.