behringer 150 Ring Mod Legendary Analog Ring LFO Module for Eurorack User Guide

behringer 150 Ring Mod Legendary Analog Ring LFO Module for Eurorack

Safety Instruction

1. Please read and follow all instructions.
2. Keep the apparatus away from water, except for outdoor products..
3. Clean only with a dry cloth.
4. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
5. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat.
6. Use only attachments/accessories specified by the manufacturer.
7. Use only specified carts, stands, tripods, brackets, or tables. Use caution to prevent tip-over when moving the cart/apparatus combination.
8. Avoid installing in confined spaces like bookcases.
9. Do not place near naked flame sources, such as lighted candles.
10. Operating temperature range 5° to 45°C (41° to 113°F).

LEGAL DISCLAIMER
Music Tribe accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein. Technical specifications, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Aston Microphones and Coolaudio are trademarks or registered trademarks of Music Tribe Global Brands Ltd. © Music Tribe Global Brands Ltd. 2024 All rights reserved.

LIMITED WARRANTY
For the applicable warranty terms and conditions and additional information regarding Music Tribe’s Limited Warranty, please see complete details online at community.musictribe.com/support

150 RING MOD/NOISE/S&H/LFO Controls

1. EXT SIG X/NOISE jack routes audio signals or noise into the ring modulator. The audio signal or noise coming in through the EXT SIG X/NOISE jack is combined with and modulated by the carrier signal routed into the EXT SIG Y/LFO jack.
2. EXT SIG Y/LFO jack routes the carrier signal into the ring modulator. The carrier signal can be in the audio range, such as a 500 Hz sine wave, or a signal from Low Frequency Oscillator (LFO).
3. R.M OUT jack sends out the final ring modulator signal.
4. PINK output jacks offer dual white pink noise outputs for use other modules.
5. WHITE output jacks offer dual white noise outputs for use with other modules.
6. EXT SIG input jack routes external signals into the S&H circuit for processing. Use the EXT/LFO/NOISE switch to optimize the EXT SIG input for different types of signals.
7. EXT/LFO/NOISE sliding switch optimizes the EXT SIG for use with control signals (EXT), signals from a Low Frequency Oscillator (LFO) or noise signals (NOISE).
8. CLOCK OUT jack sends out a clock signal generated inside the S&H circuit.
9. CLOCK RATE slider controls the internal clock signal’s rate before the clock signal is routed out through the CLOCK OUT jack.
10. S&H OUT jack sends out the final S&H (Sample & Hold) signal over cables with 3.5 mm TS connectors.
11. LAG TIME slider can be used to smooth out the changes between control voltage values as the slider is raised, similar to a portamento or glide effect on a keyboard.
12. EXT CLOCK IN input jack routes an external clock signal into the S&H circuit.
13. WAVEFORM knob selects between sine, triangle, square, ramp and sawtooth waveforms for the LFO.
14. FREQ RANGE sliding switch selects between high (H), mid (M) and low (L) frequency ranges.
15. TRIGGER jack allows a control voltage to trigger the LFO waveform by resetting the amplitude to 0. The waveform then returns to the original amplitude at a rate set by the DELAY slider.
16. FREQ slider fine-adjusts the LFO frequency within the range chosen by the FREQ RANGE switch.
17. DELAY slider controls the amount of time that elapses between the beginning of a new note and the LFO’s amplitude peak.
18. FREQ CV IN input jack allows a control voltage to control the LFO frequency in place of the FREQ slider.
19. OUTPUT LEVEL sliding switch selects between a full-strength LFO output signal (x1 setting) and a1/10th-strength signal (x 1/10 setting).
20. LFO OUT output jacks offer dual LFO outputs for use with cables with 3.5 mm TS connectors.

Power Connection

The 150 RING MOD / NOISE / S&H / LFO module comes with the required power cable for connecting to a standard Eurorack power supply system. Follow these steps to connect power to the module. It is easier to make these connections before the module has been mounted into a rack case.

1. Turn the power supply or rack case power off and disconnect the power cable.
2. Insert the 16-pin connector on the power cable into the socket on the power supply or rack case. The connector has a tab that will align with the gap in the socket, so it cannot be inserted incorrectly. If the power supply does not have a keyed socket, be sure to orient pin 1 (-12 V) with the red stripe on the cable.
3. Insert the 10-pin connector into the socket on the back of the module. The connector has a tab that will align with the socket for correct orientation.
4. After both ends of the power cable have been securely attached, you may mount the module in a case and turn on the power supply.

Installation

The necessary screws are included with the module for mounting in a Eurorack case. Connect the power cable before mounting.

Depending on the rack case, there may be a series of fixed holes spaced 2 HP apart along the length of the case, or a track that allows individual threaded plates to slide along the length of the case. The free-moving threaded plates allow precise positioning of the module, but each plate should be positioned in the approximate relation to the mounting holes in your module before attaching the screws.

Hold the module against the Eurorack rails so that each of the mounting holes are aligned with a threaded rail or threaded plate. Attach the screws part way to start, which will allow small adjustments to the positioning while you get them all aligned. After the final position has been established, tighten the screws down.

Specifications

FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION

Responsible Party Name: Music Tribe Commercial NV Inc.
Address : 122 E. 42nd St.1, 8th Floor NY, NY 10168, United States
Email Address: legal@musictribe.com

150 RING MOD/NOISE/S &H/LFO
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

Important information
Changes or modifications to the equipment not expressly approved by Music Tribe can void the user’s authority to use the equipment.

Hereby, Music Tribe declares that this product is in compliance with Directive 2014/30/EU, Directive 2011/65/EU and Amendment 2015/863/EU, Directive 2012/19/EU, Regulation 519/2012 REACH SVHC and Directive 1907/2006/EC.

Full text of EU DoC is available at https://community.musictribe.com/
EU Representative: Music Tribe Brands DK A/S
Address: Gammel Strand 44, DK-1202 København K, Denmark

UK Representative: Music Tribe Brands UK Ltd.
Address: 8th Floor, 20 Farringdon Street London EC4A 4AB, United Kingdom

Correct disposal of this product: This symbol indicates that this product must not be disposed of with household waste, according to the WEEE Directive (2012/19/EU) and your national law. This product should be taken to a collection center licensed for the recycling of waste electrical and electronic equipment (EEE). The mishandling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the efficient use of natural resources. For more information about where you can take your waste equipment for recycling, please contact your local city office or your household waste collection service.

References

• Music Tribe
• Music Tribe
• Music Tribe

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>