GARMIN GPSMAP 1222 Touch Chartplotter Installation Guide
- June 6, 2024
- Garmin
Table of Contents
GARMIN GPSMAP 1222 Touch Chartplotter Installation Guide
Important Safety Information
See the Important Safety and Product Information guide in the product box for product warnings and other important information.
When connecting the power cable, do not remove the in-line fuse holder. To prevent the possibility of injury or product damage caused by fire or overheating, the appropriate fuse must be in place as indicated in the product specifications. In addition, connecting the power cable without the appropriate fuse in place voids the product warranty.
Always wear safety goggles, ear protection, and a dust mask when drilling, cutting, or sanding.
When drilling or cutting, always check what is on the opposite side of the surface to avoid damaging the vessel.
To obtain the best performance and to avoid damage to your boat, install the device according to these instructions. Read all installation instructions before proceeding with the installation. If you experience difficulty during the installation, contact Garmin® Product Support.
Contacting Garmin Support
- Go to support.garmin.com for help and information, such as product manuals, frequently asked questions, videos, and customer support.
- In the USA, call 913-397-8200 or 1-800-800-1020.
- In the UK, call 0808 238 0000.
- In Europe, call +44 (0) 870 850 1241.
Software Update
You may need to update the chart plotter software after installation. For the instructions on how to update the software, see the owner’s manual at garmin.com/manuals/GPSMAP1222-1242 .
Tools Needed
- Drill and drill bits
- Bail mount: drill bits appropriate for the surface and hardware
- Flush mount: 13 mm (1/2 in.) drill bit, 6 mm (1/4 in.), and 3.6 mm (9/64 in.) drill bit (with nut plate), or 3.2 mm (1/8 in. with no nut plate)
-
2 Phillips screwdriver
- Jigsaw or rotary tool
- File and sandpaper
- Marine sealant (recommended)
Mounting Considerations
This device should be mounted in a location that is not exposed to extreme temperatures or conditions. The temperature range for this device is listed in the product specifications. Extended exposure to temperatures exceeding the specified temperature range, in storage or operating conditions, may cause device failure. Extreme-temperature-induced damage and related consequences are not covered by the warranty.
When selecting a mounting location, you should observe these considerations.
- The location should provide optimal viewing as you operate your boat.
- The location should allow for easy access to all device interfaces, such as the keypad, touchscreen, and card reader, if applicable.
- The location must be strong enough to support the weight of the device and protect it from excessive vibration or shock.
- To avoid interference with a magnetic compass, the device should not be installed closer to a compass than the compass-safe distance value listed in the product specifications.
- The location must allow room for the routing and connection of all cables.
- The location must not be a flat, horizontal surface. The location should be in a vertical angle.
The location and viewing angle should be tested before you install the device. High viewing angles from above and below the display may result in a poor image.
Bail Mounting the Device
If you are mounting the bracket on fiberglass with screws, it is recommended to use a countersink bit to drill a clearance counterbore through only the top gel-coat layer. This will help to avoid cracking in the gel-coat layer when the screws are tightened.
The bail-mounting hardware (screws and washers, or nuts, washers, and bolts) is not included. The bail mount bracket is included in some models. Before you can bail mount the device, you must purchase a bail mount bracket, if necessary. You must also purchase mounting hardware that fits the holes in the bail mount bracket and securely attaches it to your specific mounting surface. The size of the pilot holes required depends on the mounting hardware you purchase.
- Using the bail mount bracket (1) as a template, mark the location of the four pilot holes (2).
- Using a drill bit appropriate for your mounting hardware, drill the pilot holes.
- Secure the bail mount bracket to the surface using your mounting hardware .
- Install the bail mount knobs on the sides of the device.
- Place the device in the bail mount bracket, and tighten the bail mount knobs.
Flush Mounting the Device
Be careful when cutting the hole to flush mount the device. There is only a small amount of clearance between the case and the mounting holes, and cutting the hole too large could compromise the stability of the device after it is mounted.
The included template and hardware can be used to flush mount the device in your dashboard. There are three options for hardware based on the mounting surface material.
- You can drill pilot holes and use wood screws.
- You can drill holes and use nut plates and machine screws. The nut plates can add stability to a thinner surface.
- You can punch and tap holes, and use machine screws.
-
Trim the template, and make sure it fits in the location where you want to mount the device.
-
Secure the template to the mounting location.
-
Using a 13 mm (1/2 in.) drill bit, drill one or more of the holes inside the corners of the solid line on the template to prepare the mounting surface for cutting.
-
Using a jigsaw or a rotary tool, cut the mounting surface along the inside line on the template.
-
Place the device in the cutout to test the fit.
-
If necessary, use a file and sandpaper to refine the size of the cutout.
-
If necessary, remove the trim caps.
Use a plastic pry tool when possible. Using a metal pry tool, such as a screwdriver, can damage the trim caps and the device. -
After the device fits correctly in the cutout, ensure the mounting holes on the device line up with the larger holes on the template.
-
If the mounting holes on the device do not line up, mark the new hole locations.
-
Based on your mounting surface, drill or punch and tap the larger holes:
- For wood screws, drill 3.2 mm (1/8 in.) holes, and skip to step 18.
- For nut plate and machine screws, drill 6 mm (1/4 in.) holes in the larger hole locations.
- For machine screws without the nut plate, punch and tap M4 holes, and skip to step 18.
-
If you are using a nut plate, starting in one corner of the template, place a nut plate over the larger hole drilled in the previous step. The smaller hole on the nut plate should line up with the smaller hole on the template.
-
If the smaller hole on the nut plate does not line up with the smaller hole on the template, mark the new hole location.
-
If you are using a nut plate, drill a 3.6 mm (9/64 in.) hole in the smaller hole location.
-
Repeat to verify placement of the remaining nut plates and holes on the template.
-
Remove the template from the mounting surface.
-
Starting in one corner of the mounting location, place a nut plate on the back of the mounting surface, lining up the large and small holes. The raised portion of the nut plate should fit into the larger hole.
-
Secure the nut plates to the mounting surface by fastening the smaller machine screws through the smaller holes.
-
Install the foam gasket on the back of the device. The pieces of the foam gasket have adhesive on the back. Make sure you remove the protective liner before installing them on the device.
-
If you will not have access to the back of the device after you mount it, connect all necessary cables to the device before placing it into the cutout.
To prevent corrosion of the metal contacts, cover unused connectors with the attached weather caps. -
Apply marine sealant between the mounting surface and the device to properly seal and prevent leakage behind the dashboard.
-
If you will have access to the back of the device, apply marine sealant around the cutout.
-
Place the device into the cutout.
-
Secure the device to the mounting surface using the larger
machine screws or the included wood screws. -
Wipe away all excess marine sealant.
-
Install the trim caps by snapping them in place around the edges of the device.
Cable and Connection Considerations
- The cables may have been packaged without the locking rings installed. If so, you should route the cables before you install the locking rings.
- After connecting a locking ring to a cable, make sure the ring is securely connected and the O-ring is in place so the connection remains secure.
Power/NMEA® 0183 Cable
- The wiring harness connects the device to power, NMEA 0183 devices, and a lamp or a horn for visible or audible alerts.
- If it is necessary to extend the NMEA 0183 or alarm wires, you must use 22 AWG (.33 mm²) wire.
- This cable provides one differential NMEA 0183 input and output port.
Connecting the Wiring Harness to Power
When connecting the power cable, do not remove the in-line fuse holder. To prevent the possibility of injury or product damage caused by fire or overheating, the appropriate fuse must be in place as indicated in the product specifications. In addition, connecting the power cable without the appropriate fuse in place voids the product warranty.
- Route the wiring harness to the power source and to the device.
- Connect the red wire to the positive (+) battery terminal, and connect the black wire to the negative (-) battery terminal.
- If necessary, install the locking ring and O-ring on the end of the wiring harness.
- Insert the cable into the POWER connector on the back of the device, pushing firmly.
- Turn the locking ring clockwise to attach the cable to the device.
Additional Grounding Consideration
This consideration is applicable only to devices that have a grounding screw. Not all models have a grounding screw.
This device should not need additional chassis grounding in most installation situations. If you experience interference, the grounding screw on the housing can be used to connect the device to the water ground of the boat to help avoid the interference.
Garmin Marine Network Considerations
A Garmin Marine Network PoE Isolation Coupler (010-10580-10) must be used when connecting any third-party device, such as a FLIR® camera, to a Garmin Marine Network. Connecting a Power over Ethernet (PoE) device directly to a Garmin Marine Network chart plotter damages the Garmin chart plotter and may damage the PoE device. Connecting any third-party device directly to a Garmin Marine Network chart plotter will cause abnormal behavior on the Garmin devices, including the devices not properly turning off or the software becoming inoperable.
This device can connect to additional Garmin Marine Network devices to share data such as radar, sonar, and detailed mapping. When connecting Garmin Marine Network devices to this device, observe these considerations.
- All devices connected to the Garmin Marine Network must be connected to the same ground. If multiple power sources are used for Garmin Marine Network devices, you must tie all ground connections from all power supplies together using a low resistance connection or tie them to a common ground bus bar, if available.
- A Garmin Marine Network cable must be used for all Garmin Marine Network connections.
- Third-party CAT5 cable and RJ45 connectors must not be used for Garmin Marine Network connections.
- Additional Garmin Marine Network cables and connectors are available from your Garmin dealer.
- The NETWORK ports on the device each act as a network switch. Any compatible device can be connected to any NETWORK port to share data with all devices on the boat connected by a Garmin Marine Network cable.
NMEA 2000® Considerations
If you are connecting to an existing NMEA 2000 network, identify the NMEA 2000
power cable. Only one NMEA 2000 power cable is required for the NMEA 2000
network to operate properly.
A NMEA 2000 Power Isolator (010-11580-00) should be used in installations
where the existing NMEA 2000 network manufacturer is unknown.
If you are installing a NMEA 2000 power cable, you must connect it to the boat ignition switch or through another in-line switch. NMEA 2000 devices will drain your battery if the NMEA 2000 power cable is connected to the battery directly.
This device can connect to a NMEA 2000 network on your boat to share data from NMEA 2000 compatible devices such as a GPS antenna or a VHF radio. The included NMEA 2000 cables and connectors allow you to connect the device to your existing NMEA 2000 network. If you do not have an existing NMEA 2000 network you can create a basic one using cables from Garmin.
If you are unfamiliar with NMEA 2000, you should read the “NMEA 2000 Network Fundamentals” chapter of the Technical Reference for NMEA 2000 Products. You can find this document using the “Manuals” link on the product page for your device at www.garmin.com.
The port labeled NMEA 2000 is used to connect the device to a Pin standard NMEA 2000 network.
J1939 Engine Network Connection Considerations
You must use a Garmin GPSMAP J1939 accessory cable when connecting the chart plotter to the J1939 engine network to prevent corrosion due to moisture. Using a different cable voids your warranty.
If you have an existing engine network on your boat, it should already be connected to power. Do not add any additional power supply.
This chart plotter can connect to an engine network on your boat to read data from compatible devices such as certain engines. The engine network follows a standard and uses proprietary messages.
You should connect only one chart plotter to one engine network. Connecting more than one chart plotter to one engine network may result in unexpected behavior.
The port labeled J1939 is used to connect the device to the existing engine network. You must route the cable within 6 m (20 ft.) of the engine network backbone.
The Garmin GPSMAP J1939 accessory cable requires connection to a power source and proper termination. For more information on connecting to your engine network, see the manufacturer’s engine documentation.
NMEA 0183 Connection Considerations
- The chart plotter provides one Tx (transmit) port and one Rx (receive) port.
- Each port has 2 wires, labeled A and B according to the NMEA 0183 convention. The corresponding A and B wires of each internal port should be connected to the A (+) and B (-) wires of the NMEA 0183 device.
- You can connect one NMEA 0183 device to the Rx port to input data to this chart plotter, and you can connect up to three NMEA 0183 devices in parallel to the Tx port to receive data output by this chart plotter.
- See the NMEA 0183 device installation instructions to identify the transmit (Tx) and receive (Rx) wires.
- You must use 28 AWG, shielded, twisted-pair wiring for extended runs of wire. Solder all connections and seal them with heat-shrink tubing.
- Do not connect the NMEA 0183 data wires from this device to power ground.
- The power cable from the chart plotter and the NMEA 0183 devices must be connected to a common power ground.
- The internal NMEA 0183 ports and communication protocols are configured on the chart plotter. See the NMEA 0183 section of the chart plotter owner’s manual for more information.
- See the chart plotter owner’s manual for a list of the approved NMEA 0183 sentences that the chart plotter supports.
NMEA 0183 Connection Diagram
Lamp and Horn Connections
The device can be used with a lamp, a horn, or both, to sound or flash an alert when the chart plotter displays a message. This is optional, and the alarm wire is not necessary for the device to function normally. When connecting the device to a lamp or horn, observe these considerations.
- The alarm circuit switches to a low-voltage state when the alarm sounds.
- The maximum current is 100 mA, and a relay is needed to limit the current from the chart plotter to 100 mA.
- To manually toggle visual and audible alerts, you can install single-pole, single-throw switches.
HDMI Out Video Considerations
To prevent corrosion due to moisture, you must use Garmin GPSMAP accessory cables when connecting the chart plotter to the video display. Using different cables voids your warranty.
Through the HDMI OUT port, you can duplicate the chart plotter screen on
another device, such as a television or monitor.
The Garmin GPSMAP HDMI accessory cable is 4.5 m (15 ft.) long. If you need a
longer cable, you should use an active HDMI cable only. You need an HDMI
coupler to connect the two HDMI cables.
You must make all cable connections in a dry environment.
Composite Video Considerations
This chart plotter allows video input from composite video sources using the port labeled CVBS IN. When connecting composite video, you should observe these considerations.
- The CVBS IN port uses a BNC connector. You can use a BNC to RCA adapter to connect a composite-video source with RCA connectors to the CVBS IN port.
- Video is shared across the Garmin Marine Network, but it is not shared across the NMEA 2000 network.
Specifications
NMEA 2000 PGN Information
Transmit and Receive
Transmit
Receive
NMEA 0183 Information
You can purchase complete information about National Marine Electronics Association (NMEA) format and sentences from: NMEA, Seven Riggs Avenue, Severna Park, MD 21146 USA (www.nmea.org)
J1939 Information
The chartplotter can receive J1939 sentences. The chartplotter cannot transmit over the J1939 network.
© 2018 Garmin Ltd. or its subsidiaries
Garmin®, the Garmin logo, and GPSMAP® are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. These trademarks may not be used without the express permission of Garmin.
NMEA®, NMEA 2000®, and the NMEA 2000 logo are registered trademarks of the National Marine Electronics Association. HDMI® is a registered trademark of HDMI Licensing, LLC. The SDHC logo is a trademark of SD-3C, LLC. WiFi® is a registered trademark of Wi-Fi Alliance Corporation.
© 2018 Garmin Ltd. or its subsidiaries
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>