KOSO EGT-02 Dual Exhaust Gas Temperature Data Logger Instructions
- June 7, 2024
- KOSO
Table of Contents
KOSO EGT-02 Dual Exhaust Gas Temperature Data Logger
Thank you for purchasing our product. Before installing/operating the product, read the instructions carefully and retain them for future reference.
Attention!
- For installation, follow the steps described. Any damage caused by wrong installation shall be imputed to the users.
- To avoid a short circuit from occurring do not pull or modify the wires during installation.
- Do not disassemble or change any parts. Opening and disassembling this unit will void any warranty.
- Maintenance and repairs should be executed by our professionals only.
Symbol Description
NOTE
- Some procedures must be followed to avoid damage to the product.
- WARNING! Certain procedures must be followed to avoid damages to yourself, to the vehicle or others.
Accessories
Wiring installation instructions
Installation instructions
When installing, follow the steps below
- LCD meter(Accessory 1)
- Meter bracket(Accessory 5)
- M5 gasket x2(Accessory 11-B)
- M5 x 18L screw x2(Accessory 10)
- M4 x 18L screw x2(Accessory 9)
- M4 gasket x2(Accessory 11-A)
- Rubber(Accessory 6)
- Rubber(Accessory 7)
- Steel plate(Accessory 8)
- M4 x P0.8 nut x2(Accessory 12)
Basic function instructions
Features and settings description
●Temperature| Display unit:℃、℉ for alternative|
---|---|---
●EGT L/R| Display Range:100~1,200℃(250~2,100℉)| Display unit:1℃(℉)
○ Warning for exh. temp. (EGT L/R)| Setting range:200~1,000℃(392~1,832℉)|
Display unit:1℃(℉)
●Max. EGT record| Display Range:200~1,000℃(392~1,832℉)| Display unit:1℃(℉)
●Voltmeter| Display Range:0.8~18.0 V| Display unit:10 RPM
○ Warning for low voltage| Setting range:8.0 ~ 13.0 V| Setting unit:0.1 V
○ Warning for high voltage| Setting range:13.0 ~ 16.0 V| Setting unit:0.1 V
● Auto/Manual Record Stop| Setting range:0~60 Sec| Setting unit:1 Sec
● Backlight brightness| Setting range:1 – 5 (darkest)~ 5 – 5 (brightest)|
Setting unit:1
● Operating voltage| DC 12 V|
● Temperature range| -30~+60℃|
● Specifications| JIS D 0203|
● Meter Size| W124 X L58.5 X H22 mm|
● Meter Weight| +/- 170 g|
NOTE Design and specifications may change without further notice.
The Settings Screen Description
Over EGT L Warning Setting
- EX: To set the Warning for temp (EGT L) to 1200℉ value to 11,000 RPM
- Press the left button once to choose the setting number.
- Now the setting value will blink.
NOTE
- Setting range: 200~1,000℃(392~1832℉)
- Setting unit: 1℃(℉)
- Default value : 538℃(1,000℉)
- Press the right button to choose the setting number
- Example: Set the Warning for temp (EGT L) from 1000℉ to 1200℉
- Press the left button once to enter the warning for the temp (EGT R) screen.
- Warning for temperature (EGT R) screen.
Over EGT R Warning Setting
- EX: To set the Warning for temp (EGT R) to 1200℉
- Press the left button once to choose the setting number.
- Now the setting value will blink.
NOTE
- Setting range: 200~1,000℃(392~1832℉)
- Setting unit: 1℃(℉)
- Default value : 538℃(1,000℉)
- Press the right button to choose the setting number.
- Example: Set the Warning for temp (EGT R) from 1000℉to 1200℉
- Press the left button once to enter the warning for the Water temperature screen.
- Water temp screen.
Warning For Low Voltage Setting
- EX To set the warning for low voltage value to 11.0V
- Press the left button once to choose the setting number. Now the setting value will blink.
NOTE
- Setting range: 8.0 ~ 13.0 V
- Setting unit: 0.1 V
- Default value: 10.5 V
- Press the right button to choose the setting number.
- Example: Set the warning for low voltage value from 10.5 V to 11.0 V.
- Press the left button once to enter the warning for high voltage.
- High voltage screen.
Warning For High Voltage Setting
- EX: To set the warning for high voltage value to 16V
- Press the left button once to choose the setting number. Now the setting value will blink.
NOTE
- Setting range: 13.0 ~ 16.0 V
- Setting unit: 0.1 V
- Default value: 15.0 V
- Press the right button to choose the setting number.
- Example: Set the warning for high voltage value from 15.0 V to 16.0 V
- Press the left button once to enter the warning for the Auto/Manual Record Stop screen.
- Auto/Manual Record Stop screen.
Auto / Manual Record Stop Setting
- EX: To set the Auto / Manual Record Stop to 10 Sec.
- Press the left button once to choose the setting number.
- Now the setting value will blink. Auto / Manual Record Stop Function is off when the setting is displayed “0 SEC”.
- Press the right button to choose the setting number.
NOTE
- Setting range: 0 ~ 60
- Sec Setting unit: 1 Sec
- Default value: 0 Sec
- Example: Set the Auto / Manual Record Stop from 0 Sec to 10 Sec.
- Press the left button once to enter the backlight brightness screen.
- Backlight brightness screen.
Backlight Brightness Setting
- EX: To set backlight brightness value to 5/5.
- Press the right button once to choose the setting number.
- Now the setting value will blink.
NOTE
- Setting range: 1/5 ~ 5/5
- Setting unit: 1/5
- Default value: 3/5
- Example: Set the backlight brightness value from 3/5 to 5/5.
- Press the left button once to enter the main screen.
- Main screen
How to switch functions
- Left button function instructions(EGT L MAX)
- Press the left button once to switch from EGT L/R to MAX EGT L/R.
- Hold the left button for 3 seconds,to clear the MAX recording screen.
- press the left button once to return to the Main screen.
- Main screen.
Right button function instructions (EGT R Voltage)
- Press the right button once to switch from EGT R to Voltage.
- Press the right button once to switch from Voltage to EGT R.
- In the main screen, press the right & left buttons to enter the recording screen. (Check section 5-2 for detail)
- In the recording screen, press the right & left buttons to enter the Play Screen. (Check section 5-3 for detail)
- In the main screen, hold the right button and the left button for 3 seconds to enter the setting screen. (Check section 4 for details)
Operating instructions of the recording screen
- Main screen, press the right & left buttons to enter the Recording Screen.
- Recording Screen Hold the left button for 3 seconds,to enter the operating screen for clearing records.
- For the recording screen, press the left button once to start recording.
- Now the REC will blink.
- At the screen during recording, press the left button once to stop recording.
- The first run has been recorded.
- To stop the recording screen, press the left button once to enter the recording screen for the second entry.
- Currently, it is on the recording screen for the second entry.
- Currently, it is on the recording screen for the third entry.
- Currently, it is on the recording screen for the fourth entry.
- Recording screen, Press the right & left buttons to enter the playback Screen.
- playback Screen
Operating instructions of the playback screen
- Recording screen, Press the right & left buttons to enter the playback screen.
- Press the left button once to choose the run to be played.
- Press the right button to choose how the run is played.
- Press the left button once to enter the play / stop screen.
- Hold the right button for 3 seconds, to enter the Main screen.
- Main screen
Operating instructions for clearing the recorded data
- In the recording screen, hold the left button for three seconds to enter the operating screen for clearing data.
- Hold the left button for 3 seconds, clearing data.
- Press the right or left button for 3 seconds, and cancel clearing data.
- Clearing the data; wait for a few seconds to complete clearing.
- Done
Multiple Warning Display Operating Description
- Left Screen
- Press the left button once to switch from EGT L to RPM.
- Right Screen
- Press the right button once to switch from EGT R to voltage.
- Press the right button once to switch from voltage to EGT R.
- Now the warning value will blink.
- NOTE Return to the first after 10 seconds.
Troubleshooting
The following situations do not indicate malfunctions of the product. Check the following before taking it in for repair.
Trouble | Check item | Trouble | Check item |
---|---|---|---|
The meter doesn’t work when the power is on. | **●The power isn’t |
supplied to the gauge.**
→Make sure the wiring is connected.
The wiring and fuse are not broken.
→The battery is too old to supply needed
power (DC 12 V).
●Check the voltage of your battery, and
make sure the voltage is over DC 12 V.
| Voltage doesn’t appear or appears incorrectly.| ●Wiring might be poorly installed
→Confirm whether the wirings for
the connector are properly installed and whether the wirings are connected.
The meter shows the wrong information.| Temp does not appear or appear incorrectly.| ●Check the sensor
→ Check whether the wiring is disconnected or has fallen off.
If the problems still cannot be solved, contact our technical department for assistance.