CHORD BerTTi Stereo Power Amplifier User Manual
- June 13, 2024
- chord
Table of Contents
Chord Electronics
Product Communication
User manual
Introduction
The BerTTi is a next-generation 75-watt stereo power amplifier containing the very latest ULTIMA circuit topology. This manual provides all the information required to set up and operate the BerTTi. Further details can be found online at: chordelectronics.co.uk/product/bertti.
2.1 Safety and care
- Do not allow the device to come into contact with water or liquids.
- Do not spray cleaning products onto the device. Use a clean microfibre cloth to clean the casework.
- A further safety document is included in the box.
- The device does not contain any user-serviceable components. Do not attempt to open, dismantle or apply internal third-party devices to it. Doing so will void the warranty.
Support and warranty
For support, please contact the supplying retailer before contacting Chord Electronics. Further help can be found at chordelectronics.co.uk/getsupport
At the point of sale, Chord Electronics Ltd. provides the BerTTi with a
comprehensive three-year warranty, which covers defects in materials and
workmanship through fair usage.
The warranty is transferable with proof of purchase, however, the warranty on
ex-demonstration units begins from the retailer‘s date of purchase. Warranty
claims must be made via the supplying retailer.
For the best possible support and service, please register your purchase with
Chord Electronics at: chordelectronics.co.uk/register-
product/
Connections and controls
4.1 Rear and front panels
A Power on/off switch
B 10 A IEC AC inlet
C Right channel speaker positive terminal
D Right channel line level RCA input
E Right channel balanced XLR input
F Right channel speaker negative terminal
G 12 V trigger connection
H Grounding post
J Left channel speaker negative terminal
K Left channel balanced XLR input
L Left channel line level RCA input
M Left channel speaker positive terminal
N Power/standby switch and status LED
Power and earthing connection
The BerTTi has been designed to connect to power with the supplied 10 A power cable. If hum or buzz occurs, try either a good-quality earthed power distribution block, or the rear panel ground terminal and connect to an available earth point.
Inputs
Connect the BerTTi to any preamp output using good-quality standard RCA cables, or connect using balanced XLR cables. Note only one input type can be used at once: the BerTTi does not support ‘switching’ between the input connection types.
WARNING: Please DO NOT attempt to use both the RCA and XLR inputs simultaneously. Any subsequent damage to connected equipment will not be covered by Chord Electronics.
Connecting to loudspeakers
Connect the BerTTi to loudspeakers using good-quality loudspeaker cable, terminated with 4 mm banana plugs. Unscrew BerTTi’s loudspeaker terminals to use spade-plug-terminated cable. Although bare wire can be used, it is not recommended.
Power on/off
With all cable connections successfully made and the volume on connected
preamps set to zero, switch the rear-panel power button to ‘on’ and depress
the front panel button to switch the unit from standby mode to ‘on’. The front
panel LED will turn from green (standby) to cyan (on), once the BerTTi has
performed its safety check. BerTTi is ready for use and the preamp volume can
now be carefully increased for playback.
The BerTTi consumes very little energy in standby mode and if desired, can be
left switched ‘on’ at all times.
12 V trigger
The BerTTi includes a 12 V trigger input. Partnering devices with a compatible 12 V trigger output can be connected for simultaneous power on/off from standby mode. When connected the front panel button LED will turn yellow and once triggered the LED will change to purple.
Placement
The BerTTi benefits from extensive casework ventilation, plus a cooling fan
for more demanding environments. Always ensure the BerTTi is used in a well-
ventilated setting, away from direct sunlight and heat sources, with
sufficient space (at least 10 cm) around the unit.
The BerTTi has internal thermal protection which increases the speed of the
cooling fans if excessive temperatures are reached. Should this occur, check
the BerTTi has adequate ventilation and/or reduce the volume level until the
unit has cooled and the fans have slowed. It is normal for the unit to become
warm when operating.
If stacking the BerTTi with other units, it is advisable to place the unit on
top of others.
Technical Specifications
Please go online for the most recent specifications: www.chordelectronics.co.uk
| Dimensions | 59 mm (H) 235 mm (W) 256 mm (D) |
|---|---|
| Weight | 3.75 kg |
| Output power | 75 W into 8 Ω |
| Frequency range | 5 Hz-100 kHz +/- 0.5 dB |
| THD | 0.01% |
| Signal-to-noise ratio | 87 dB (A-weighted) |
| Input impedance | 100 kΩ unbalanced/balanced |
| Input sensitivity | 0.78 V |
| Gain | 30 dB |
The Pumphouse, Farleigh Lane, East Farleigh, Kent,
ME16 9NB. Great Britain.
+44 (0) 1622 721 444
info@chordelectronics.co.uk
chordelectronics.co.uk
References
- Chord Electronics - High-End Audio for Hi-Fi Enthusiasts & Professionals
- Support | Chord Electronics
- BerTTi - Chord Electronics Ltd
- Register Your Product | Chord Electronics
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>