ARISTA C-130E Wireless Access Point User Guide

Quick Start Guide
C-130E Access Point
Arista Networks
www.arista.com
DOC-03484-02

Headquarters
5453 Great America Parkway
Santa Clara, CA 95054
USA
408 547-5500
www.arista.com| Support
408547-5502
866 476-0000
support-wifi@arista.com| Sales
408 547-5501
866 497-0000
sales@arista.com
---|---|---

© Copyright 2020 Arista Networks, Inc. The information contained herein is subject to change without notice. Arista Networks
and the Arista logo is the trademark of Arista Networks, Inc in the United States and other countries. Other product or service names may be trademarks or service marks of others.

About this Guide

This installation guide explains how to deploy the C-130E access point (AP).
Important: Please read the EULA before installing C-130E. You can download and read the EULA from https://www.arista.com/en/support/product- documentation.
Installing the AP constitutes your acceptance of the terms and conditions of the EULA mentioned above in this document.
Intended Audience
This guide can be referred by anyone who wants to install and configure the C-130E access point.
Document Overview
This guide contains the following chapters:

• Package Content on page 4
• C-130E Overview on page 7
• Install the C-130E on page 11
• Access Point Troubleshooting on page 16

Note: All instances of the term ‘server’ in this document refer to the Wireless Manager unless the server name or type is explicitly stated.
Product and Documentation Updates
To receive important news on product updates, please visit our website at https://www.arista.com/en/support/product-documentation. We continuously enhance our product documentation based on customer feedback.

Package Content

The access point (AP) package must contain the components shown in the following figure.

Figure 1: Package Components

Table 1: Labels: Package Components

Important: The MAC address of the AP is printed on a label at the bottom of the product and the packaging box. Note down the MAC address, before mounting the AP on the ceiling or at a location that is difficult to access.
If the package is not complete, please contact Arista Networks Technical Support Team at support-wifi@arista.com, or return the package to the vendor or dealer where you purchased the product.

C-130E Overview

C-130E is a 4×4 802.11a/b/g/n/ac access point with three radios.
This chapter provides an overview of the C-130E and describes:

• Front Panel of C-130E
• Rear Panel of C-130E
• Top Side Ports on C-130E
• External Antenna Ports on C-130E

Front Panel of C-130E

The front panel of the C-130E has 4 functional LEDs that indicate the working of the device.

Figure 2: Front Panel LEDs

Table 2: Labels: Front Panel LEDs

Power LED: The following table describes the Power LED states.
Table 3: Power LED States Description

| Green| Orange
---|---|---
Solid| Running at full capability| Running at reduced capability
Blinking| Received IP address, but not connected to the server| Did not receive an IP address

Reduced capability indicates that the AP is getting lower than the required maximum power from the PoE switch, i.e., 802.3af instead of 802.3at.
Radio LEDs: ON when the corresponding radio is operational.

Rear Panel of C-130E

The rear panel of the C-130E provides a PoE+ Ethernet port that enables you to connect the device to a wired LAN through a switch or a hub and power the device by using the 802.3af/802.3at standard.

Figure 3: Rear Panel

Table 4: Labels: Rear Panel

Gigabit
Ethernet (LAN1/PoE+)| Gigabit Ethernet port used to| RJ45| • 10/100/1000 Mbps Gigabit Ethernet
• 802.3af/80 Class 0  PoE/PoE+
• PoE input voltage: 48V
If using PoE (802.3af) some
features will be disabled

Top Side Ports on C-130E

Describes the supported AC power supplies and lists the power cables you can use to connect the supply to a power source.

Figure 4: Top Side Panel

Table 5: Labels: Top Side Panel

terminal session via serial
connection.| RJ45| • RS 232 Serial Bits per second:
115200
• Data Bits: 8, Stop Bits: 1
• Parity: None
• Flow Control: None
USB| USB 2.0 port| Not in use| Not in use
Reset Pinhole| Reset to factory default settings| Pinhole push button| Hold down and power cycle the

The Reset Pin Hole and the USB port are on the top side of the device as shown in the figure above. The Reset Pinhole resets the C-130E device to factory defaults. To reset the device, press and hold the Reset Pin Hole for 10 sec until all LEDs go off which indicates that the device has rebooted. Pressing the Reset Pin Hole while the device is booting up will not have any effect. You should perform this operation only when the device is running. When you reset the device, the following settings are reset:

• Config shell password is reset to config.
• Server discovery value is erased and changed to the default, wifi-security-server.
• All the VLAN configurations are lost.
• If static IP is configured on the device, the IP address is erased and DHCP mode is set. If DHCP fails the factory default IP address of the device is set to 169.254.11.74.

The USB port on the C-130E is currently not in use.

External Antenna Ports on C-130E

Make sure the antennas are connected to the respective RP-SMA type of connector ports as shown below:

Figure 5: External Antenna Ports

Install the C-130E

This chapter contains the step-wise procedure to install the C-130E device.
Zero-Configuration of C-130E as Access Point
Zero-configuration is supported under the following conditions:

• The device is in AP mode with background scanning on and no SSID configured.
• A DNS entry wifi-security-server is set up on all the DNS servers. This entry should point to the IP address of the server. By default, the AP looks for the DNS entry wifi-security-server.
• The AP is on a subnet that is DHCP enabled.

Important: If the device is placed on a network segment that is separated from the server by a firewall, you must first open port 3851 for User Datagram Protocol (UDP) and Transport Control Protocol (TCP) bidirectional traffic on that firewall. This port number is assigned to Arista Networks. If multiple devices are set up to connect to multiple servers, zero-configuration is not possible. In this case, you must manually configure the APs. See the Access Point Configuration Guide on our website at https://www.arista.com/en/support /product-documentation.
Take a configured AP; that is, ensure that a static IP is assigned to the AP or the settings have been changed for DHCP. Note down the MAC address and the IP address of the AP in a safe place before it is installed in a hard-to-reach location. The MAC address of the AP is printed on a label at the bottom of the product.
The steps to install the device are as follows:

• Mount the C-130E
• Power the Access Point
• Connect Access Point to the Network

Mount the C-130E

The steps to mount the C-130E involve:

• Mounting Instructions using the Standard Package Contents
• Mounting Instructions using the Silhouette or Interlude Bracket Mount
• Mounting Instructions using the Wall Mount Bracket

Important: To prevent disconnection or tampering by unauthorized personnel, it is extremely important to install the device such that it is difficult to unplug the device from the network or from the power outlet.
Note: You should label the devices using MAC addresses or at least your own convention. For example, use serial numbers, so that you can easily identify the devices.
Mounting Instructions using the Standard Package Contents The mounting procedure can be divided into two parts:

Mounting Instructions using the Standard Package Contents

The mounting procedure can be divided into two parts:

1. Affixing the bracket to the T -grid: Use the mounting bracket to install the C-130E on the ceiling. Fix the bracket to the T-grid and rotate the bracket so that it snaps on the T-grid.
   The bracket is now parallel to an arm of the T-grid. Ensure that the bracket is properly snapped to the T-grid. Refer to the images given below.

2. Mounting C-130E on the bracket: Place the first mounting post on the rear side of the device onto the lower notch of the bracket. Rotate the device such that the center mounting post fits into the center notch on the bracket. Ensure that all the mounting posts on the rear side of the device are snapped into the respective notches on the bracket.
   The mounting posts on the rear-side of the device are now properly fit in the respective notches of the bracket and the device is mounted properly.

Mounting Instructions using the Wall Mount Bracket

The Wall mounting bracket is not a part of the standard package and must be procured separately. Attach the wall-mounting bracket with the help of screws onto the wall. Pull the side latch to unlock the wall mount back affix the device on the wall mount bracket by placing the device stubs in the bracket’s placeholder. Lock the side latch and affix the device firmly with the screw.

Mounting Instructions using the Silhouette or Interlude Bracket Mount

The Silhouette/Interlude mounting bracket is not a part of the standard package and must be procured separately.
The mounting instructions for the Silhouette/Interlude Bracket Mount are very similar to the Standard Package Content’s mounting instructions. Refer to the instructions mentioned in Mounting Instructions using the Standard Package Contents.

Power the Access Point On

The C-130E device can be powered on by plugging one end of the Ethernet cable into the PoE+ (802.3at) switch or injector and the other end into the Ethernet/PoE+ port on the C-130E. Ensure the PoE+ source you are using is turned ON.
Note: You can also use regular PoE (802.3af). However, there are certain drawbacks to it:

• The USB is disabled.
• The other ethernet port is disabled.
• The 2.4 GHz radio is downgraded to 1×1 TX/RX capability and Tx power of 15 dBm or lower, (or as set in the device template)
• The 5 GHz radio is downgraded to 2×2 18 dBm or lower, (or asset in the device template)

As an alternative to PoE+, you can insert a power adaptor plug into an AC power outlet and the other end into the power input port on the C-130E.

Using C-130E with Power Adapter

To power up the device with a power adapter, perform the following steps:

1. Plug the power cable into the DC power receptacle at the rear of the device.
2. Plug the other end of the power cable into a 110V~240V 50/60 Hz AC power source.

Wait for a few minutes for the device to power on. Further, you can refer to the LED details table to verify the functioning of the device.

Connect Access Point to the Network

The device can be connected to the network by connecting through a LAN cable or a POE+ injector. If you are using a PoE+ injector, make sure the data connection is plugged into a suitable switch port with proper network connectivity.
To connect C-130E to the network, you should meet the following prerequisites:

• Ensure that a DHCP server is already available on the network to enable network configuration of the C-130E.
• DNS should be able to resolve the server discovery primary: redirector.online.spectraguard.net, secondary: wifi-security-server).
• AP with valid IP address from DHCP server or a valid static IP address1 to communicate with Wireless Manager.
• Check the LEDs Status on the device to ensure that it is operational and connected to the server.

If the conditions above are true, the device should be connected and ready to go operational.
Note: If zero-configuration fails, the AP must be configured manually.
Important: If DHCP is not enabled on a subnet, the AP cannot connect to that subnet with zero configuration. If the DNS entry is not present on the DNS servers, or if you do not have the DHCP server running on the subnet, you must manually configure the AP. For details on configuring an AP manually, see the Access Point Configuration guide on our website at https://www.arista.com/en/support/product-documentation.

Access Point Troubleshooting

The table below lists some of the troubleshooting guidelines for the access point (AP).

server is on and available on the VLAN/subnet to which the AP is connected. If the AP still fails to get a valid IP address, you can reboot it to see if the problem is resolved.
Unable to connect to the server.| • Ensure that the server is running and is reachable from the network
to which the AP is connected. If a firewall or a router has Access
Control Lists (ACLs) enabled between the AP and the server, ensure that traffic on UDP port 3851 is allowed.
• Use the IP-based server discovery method and ensure that you have correctly entered the DNS name, wifi-security-server, on the DNS server.
• Ensure that the DNS server IP addresses are either correctly
configured, or are provided by the DHCP server.
• The AP might fail to authenticate with the server. In this case, an
‘Authentication failed ‘ event is raised on the server. Refer to the
event for recommended action.
The AP has encountered a problem.| • If you are using Arista Cloud Services, then open the TCP port 443 (SSL). If you have an on-premises installation, then open UDP port 3851 and port 80.
• If you are using a Proxy, Web Accelerator, or URL Content Filter
between the AP and the Internet, ensure that the settings allow
communication between the AP and Arista Cloud Services.
• If your configuration requires you to specify an exact IP address
or IP range for Arista Cloud Services, please contact
support-wifi@arista.com.

Appendix A: AP-Server Mutual Authentication

The AP-server communication begins with a mutual authentication step in which the AP and server authenticate each other using a shared secret. The AP-server communication takes place only if this authentication succeeds.
After the authentication succeeds, a session key is generated. All communication between the AP and server from this point on is encrypted using the session key.
The AP and server are shipped with the same default value of the shared secret. Both the server and the AP have CLI commands to change the shared secret.
Note: After the shared secret (communication key) is changed on the server, all APs connected to the server will automatically be set up to use the new communication key. APS that are not connected to the server at this time must be manually set up with the same communication key to enabling communication with this server.
Note: Although the server is backward compatible—that is, older version APs can connect to a newer version server—this is not recommended.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>