Kooduu Synergy PRO User Manual

SYNERGY PRO-SERIES
WWW.KOODUU.COM NOMENTA INDUSTRIES INTERNATIONAL BV
Kenaupark 33-2,2011 MR,Haarlem, The Netherlands

Introduction
Dear Customer,
Thank you for purchasing our Kooduu Synergy PRO. We hope you enjoy listening to your favorite tunes whilst enjoying your new designer lamp and
cooler in one.
This product complies with the statutory national and European requirements.
To maintain this status and to ensure safe operation, you as the user must observe these operating instructions!

These operating instructions are part of this product. They contain important notes on commissioning and handling. Also, consider this if you pass on the product to any third party. Therefore, retain these operating instructions for reference!

All company names and product names are trademarks of their respective owners.
All rights reserved.

Intended use

This Kooduu Synergy PRO is intended to be used as a lifestyle product.
The product serves as a multifunctional speaker and light. Its top chamber can be used for chilling wine or used as a planter.
Any use, other than described above, can damage the product. Additionally, this is connected to dangers, such as short circuits, fire, electric shock, etc.
No part of this product must be modified or converted!
Read these operating instructions completely and attentively; they contain important information on setup, function, and operation. Always observe the
safety information!
The included power adaptor is for INDOOR charging only.

Box contents

• Floor Bluetooth speaker and LED light
• Operating Manual
• USB cable
• USB charger
• Support Stands
• Screws

Safety information

The warranty/guarantee will expire if the damage is incurred resulting from non-compliance with these operating instructions. We do not assume any liability for consequential damage!
Nor do we assume any liability for damage to property or personal injury caused by improper use or failure to observe the safety information. In
In such cases, the guarantee/warranty will expire!
The following safety information is intended not only for the protection of your health but also for the protection of the device. Please read the following  carefully:
The unauthorized conversion and/or modification of the product is inadmissible for safety and approval reasons.
The product is only suitable for dry areas. Do not expose it for long periods of time to direct sunlight, heat, cold, dampness, or wetness; otherwise, it may cause damage to the product.
There is a danger of fire or potentially fatal electric shock. If this is the case, first shut down the respective socket (e.g. switch off circuit breaker) and then pull the power adaptor from the socket. Disconnect all cables from the device. Do not operate the product anymore afterward, but contact your local dealer or get in touch with us at https://www.kooduu.com/return- policy/
Do not place any open sources of fire, such as burning candles, on the device.
Handle the product with care. It can be damaged by impact, blows, or when dropped even from a low height.
Note: The handle and aluminum ring are not waterproof and need to be kept dry at all times.

This product is not a toy and is not suitable for children. Children cannot judge the dangers involved when handling electrical devices.
Do not leave packing material unattended. It may become a dangerous toy for children.
Also, observe the safety and operating instructions of any other devices that you connect to the speaker.

Product overview

Keys function & Bottom
A1 On/Off switch
A2 USB charging port| Charging
B1 USB cable
B2 USB charger| Assembly Parts
C1 Support Stands
C2 Screws| LED indicator
D1 Charging LED
D2 Mode LED
---|---|---|---

Setup mono speaker (single-unit) connection.

5.1
Step 1:
Before first use, turn off the Bluetooth function of any other Bluetooth device near the speaker.
Step 2:
Press the On/Off key for about 3 seconds on the unit. You will hear a start-up sound and the blue LED indicator light will fast flash.
Step 3:
Now turn on “ Bluetooth ” only our mile phone and search for “Synergy(35/50/65) PRO” on discoverable devices in your Bluetooth menu and pair with the unit.
Step 4:
You will be prompted for a code. The code is “5 6 3 8”
Step 5:
After you hear the connection sound “beep” the product is successfully paired.
This can be confirmed by the CONNECTED sign/wording on your smart device.
Step 6:
The Blue indicator light will become solid Blue. You can now play your favorite music.
Volume settings

In order to adjust the volume use the connected smart device to adjust the volume up or down.

Pairing to new phone

If you need to pair the speaker to a new device, you need first turn off the Bluetooth on the connected phone. Wait for 5 seconds and then connect with the new device.

Turn off the Synergy Pro

To turn off the product press and hold the on/off button until the LED light turns off.

Setup multiple speaker connections

If you have multiple Kooduu products you want to pair make sure to follow these instructions.
Step 1:
Before first use, turn off the Bluetooth function of any other Bluetooth devices near the speakers.
Step 2:
Press the On/Off switch for about 3 seconds on the first unit. There will be a start-up tone and the blue LED indicator light will flash on both units.
Step 3:
Choose the unit that will be the “Master”
Step 4:
Double press the “Master’s” ON/OFF button – the blue LED will now flash slower.
Step 5:
Choose the next “Follower” unit to connect.
Step 6:
Single press the “Follower’s” ON/OFF button – the blue LED will now turn off.
Step 7:
Let the “Follower” automatically connect to the “Master” speaker. You will hear a “beep” tone once the connection between the “Follower” and the “Master” speaker is successfully made.
Repeat step 5 to Step 7 with all the “Follower’s” you wish to pair to the “Master”.
Step 8:
In order to finalize the pairing, double press the “Master’s” ON/OFF button – the blue LED will now flash quickly again.
DO NOT PRESS ANY OF THE “FOLLOWER” UNITS ON/OFF BUTTONS.
Step 9:
The “Master” unit is now visible for Bluetooth pairing.
Step 10:
Enter the Bluetooth menu on your smart device or computer and start pairing with Synergy Pro “Master”. Fast flashing LED.
Step 11:
You will be prompted for a code. The code is “5 6 3 8”
Step 12:
After you hear the connection sound “BEEP” the product is successfully paired.
This can be confirmed by the CONNECTED sign/wording on your smart device.
The LED of the “Master” is now solid Blue.
Once all units have been paired the settings will be remembered and next time the lamps are turned on, they will “automatically” pair to the previous settings.
NOTE: If you do not finalize the pairing by double-pressing the “Master’s” ON/OFF; no successful Bluetooth connection can be established. The
“Master’s” Bluetooth will be visible on your smart device, but no connection is possible.

Adding more “Follower” units to an existing multi-system:

Step 1:
Locate the “Master” unit.
Step 2:
Double press the “Master” (while the unit is on).
Step 3:
Choose the next “Follower” unit to connect.
Step 4:
Single press the “Follower’s” ON/OFF button – the blue LED will now turn off.
Step 5:
Let the “Follower” automatically connect to the “Master” speaker. You will hear a “beep” tone once the connection between the “Follower” and the “Master” speaker is successfully made.
Step 6:
In order to finalize the pairing, double press the “Master’s” ON/OFF button – the blue LED will now flash quickly again.

DO NOT PRESS ANY OF THE EXISTING “FOLLOWER” UNITS ON/OFF BUTTONS.

“Slave” units
Solid blue LED| The product is paired by Bluetooth with a smart device
Product is on — NO blue LED| Product is in “Follower” mode — waiting to pair with “Master” unit
2ndLED is RED| The product is connected with a USB charger and is charging
2″ LED is Green| The product is connected with a USB charger and is fully charged
Current MODE| MODELED indicator| Button Press| New MODE| MODELED indicator
---|---|---|---|---
OFF| N/A| 2 seconds long press| ON| Fast blue flashing
ON| (Any)| 2 seconds long press| OFF| N/A
Master Bluetooth Pairing| Fast blue flashing| Double Press
Master — looking| for Follower Pairing| Slow blue flashing
Master — looking for Follower Pairing| Follower Slow blue
flashing| Double Press| Master —Bluetooth Pairing| Fast blue flashing
Master Bluetooth Pairing| Fast blue flashing| Single Press| Follower| No LED
Follower| No LED| Single Press| Master — Bluetooth Pairing| Fast blue flashing
OFF| N/A| Hold 10 seconds (RESET)| Master — Bluetooth Pairing| Fast blue flashing

Reset the Synergy Pro

In order to go back to the factory setting on your Synergy Pro.
Turn off the lamp by holding the ON/OFF button for 2 seconds (if on).
Wait 3 seconds.
Now hold and press the ON/OFF button for 10 seconds until the lamp turns on, off, and on again.
This needs to be done if you want the lamp to “forget” any previously paired phones or Master/Follower lamps.

 Charging

Lift up the small silicone part on the bottom of your Kooduu Synergy PRO product and insert the USB jack into the USB port. If you are using the product for the first time, it is recommended to leave the USB jack plugged-in for a minimum of 12 hours, in order to charge the internal battery fully.
General Notes:
For an optimal experience, keep your mobile device within 35m of the LEFT channel speaker unit.
Position your 2 units in the same room or outdoor area within 3-5m of each other, free from obstructions.
The performance of your KOODUU Synergy PRO products may vary based on device, distance, and other environmental factors.

Maintenance and cleaning

Servicing or repair must only be carried out by a specialist or specialist workshop. The product contains no parts that require servicing by you.
Therefore, never open the product (except for the procedures described in these operating instructions).
A dry, soft and clean cloth is sufficient for cleaning the outside.

Never use any aggressive cleaning agents, alcohol, or other chemical solutions that would damage the casing (discoloration).

Disposal

a) Product
Electronic devices are recyclable waste and must not be disposed of in the household waste!
At the end of its service life, dispose of the product according to the relevant statutory regulations.
Remove any inserted batteries/rechargeable batteries and dispose of them separately from the product.

b) Batteries and Rechargeable Batteries
You as the end-user are required by law (Battery Ordinance) to return all used batteries/rechargeable batteries. Disposing of them in household
waste is prohibited!
Batteries/rechargeable batteries that contain any hazardous substances are labeled with the adjacent icon to indicate that disposal of domestic waste is forbidden. The descriptions for the respective heavy metals are Cd=cadmium, Hg=mercury, Pb=lead (the names are indicated on the battery/rechargeable battery e.g. below the rubbish bin symbol shown on the left).

You may return used batteries/rechargeable batteries free of charge at the official collection points in your community, in our stores, or wherever
batteries/rechargeable batteries are sold.
You thus fulfill your statutory obligations and contribute to the protection of the environment.

Declaration of Conformity
Hereby, Momenta Industries International B.V. declares that the radio equipment type ‘Synergy PRO-sery’s is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://kooduu.com/ec-declaration-of- conformity.

Bluetooth-Standlautsprecher mit LED-Licht und Weinkühler
Modell: Kooduu Synergy PRO
Benutzerhandbuch
Version 1.2
2019

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>