GMG Pellet Smokers – Prime Grills User Guide
- June 6, 2024
- GMG
Table of Contents
GMG Pellet Smokers – Prime Grills
GRILL PARTS LIST
- Grill Lid Handle
- Chimney
- Internal Grill Light
- Collapsible Front Shelf
- Front Shelf Mount Brackets
- Locking Caster Wheel Legs
- Oversized Green Wheel Legs
- Bottom Storage Shelf
- Grill Grates
- Grease Tray
- Heat Shield
- Heat Shield Adjustment Handle
- Grease Bucket
- Side Shelf
- Hopper Safety Guard
- Food Probes
POWER COMPONENTS
- AC Power Cord
- Alligator Clips
- DC Power Cord
HARDWARE
- Grill Socket Wrench
- Shelf Arm Bolt M6x35mm
- Grill Assembly Bolt M6x20mm
- Small Tool Hook Screw M5x6mm
- Control Board Antenna
- Lid Handle Spacers
ASSEMBLY
PLEASE READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY
**UNBOXING & LEG INSTALLATION
**
IMPORTANT! The grill is very heavy. Always use 2 people when lifting the grill. 10mm
UNBOXING
Open and remove front shelf.
UNBOXING
Open STARTER BOX. Reference parts list. Remove cardboard filling.
UNBOXING
Cut down box corners to access grill. Remove internal parts & legs
LAY BACK FOR LEG ACCESS
Lay grill down on it’s back. Keep on cardboard to prevent scratches.
INSTALL LEGS
Use extra cardboard to prop up grill base for easier leg installation.
Install legs correctly as shown here
BOTTOM SHELF
IMPORTANT! The grill is very heavy. Always use 2 people when lifting the grill.
STAND GRILL UPRIGHT
Carefully lift grill up and stand upright
INSTALL BOTTOM SHELF
Slide shelf down to sit on shelf arm bolts. Align with grooves under shelf.
LID HANDLE
IMPORTANT! Keep 2 spacers on each side of the grill lid to minimize heat transfer to the handle.
REMOVE HANDLE
Unscrew handle from inside grill lid.
Flip hand around to the front and fasten to lid as shown here.
FRONT & SIDE SHELVING
NOTE: Front shelf mount brackets attach in the same holes used for the front legs.
MOUNT BRACKETS
Install brackets in leg holes.
FRONT SHELF
Attach front shelf hinges to brackets.
SIDE SHELF
Line up the bullets with the pins on side wall and clip shelf into support bar.
CHIMNEY
IMPORTANT! Make sure the chimney cap ALWAYS stays open.
REMOVE BOLTS
INSTALL CHIMNEY
HEAT SHIELD
IMPORTANT! For proper heat shield positioning, use the marks on the adjuster handle. The grill wall should align with the -.5 mark on the handle, setting the heat shield 9.25 in. from the left inside grill wall.
16 HEAT SHIELD
Insert heat shield onto stainless steel slider mount brackets.
HEAT SHIELD ADJUSTER
Insert adjuster handle into hole on right side of grill wall and screw into head shield.
HEAT SHIELD POSITIONING
Recommended position for even heat distribution: approx. 9.25 in. from left wall.
GREASE TRAY, GRATES, & GREASE BUCKET
IMPORTANT! Make sure to insert grease tray as shown below for proper temperature reading and grease drainage.
GREASE TRAY
Follow grease tray cut-outs as shown.
GRILL GRATES
Insert grates as shown.
GREASE BUCKET
Hang bucket on drip spout
HOPPER GUARD
INSERT HOPPER GUARD
Open lid and install safety guard.
ANTENNA
INSTALL ANTENNA
Screw antenna onto control board.
YOUR GRILL IS READY!
PLEASE READ THE SAFETY INFORMATION AND OPERATING INSTRUCTIONS IN YOUR MANUAL BEFORE INITIAL START UP
HAVE QUESTIONS?
The new grill owners guide is your one-stop-shop for everything from initial fire-up to general operating tips and troubleshooting. For support, questions feel free to check out our support page.
NEW GRILL OWNERS
greenmountaingrills.com/new-grill-owners/
GMG SUPPORT
greenmountaingrills.com/support/