NEXSENS G2-Rain Alert System User Guide

June 6, 2024
NEXSENS

nexsens_logo

NEXSENS G2-Rain Alert System

NEXSENS G2-Rain Alert System image

IMPORTANT – BEFORE FIELD DEPLOYMENT : Completely configure new G2 systems with a web connection in a nearby work area. Operate the system for several hours and ensure correct sensor readings. Use this test run to become familiar with the features and functions.

Overview

  • The G2-RAIN Alert System includes an integrated mo-dem. Power is provided internally through (2) D-Cell lithium batteries. An external power cable (optional ac-cessory) allows connection to an SP-Series solar panel for recharging the internal batteries and direct communica-tion (serial to PC). The integrated tipping bucket supplies accurate rainfall measurements (one tip per 0.01” rain).
  • Data is accessed and stored on the WQData LIVE web datacenter. An easy-to-use dashboard and built-in sensor library automatically facilitate setup and configuration.

What’s Included?

(1) G2-RAIN-RTU
(1) G2 series battery pack (installed)
(1) Rain gauge
(1) SMA antenna
(1) 9/64” hex wrench
(1) Quick start guide

  1. To get started:
    Go to WQDataLIVE.com

    • Create a new account or sign into an existing account.
    • Choose or create the project that will contain the data logger by selecting the Projects link from the bottom right footer of the page.
    • Open the project and go to the ADMIN tab located at the top of the project dashboard and click Settings.
  2. From there, choose the Project/Site pull down menu and select the site for the new data logger.

    • If a site has not been created, select New Site.
  3. Enter the claim code listed below int o the space provided under Assigned Devices.

  4. Remove the siphoning tipping bucket by using the 9/64” hex wrench to loosen the (3) bolts connecting the bucket and RTU.

    •  Lift the bucket up gently.
    • Remove the rubbing band from the tipping apparatus.
    • Reinstall the bucket and tighten bolts.
      NEXSENS G2-Rain Alert System figLift bucket to remove the rubber band on the tipping apparatus.
  5. Attach the antenna to the copper SMA connector found on the bottom of the G2-RTU.
    NEXSENS G2-Rain Alert System fig1Rotate the antenna clockwise onto the threads of the SMA connector.

  6. Internal power- Use the included flathead screwdriver to turn the black power set screw clockwise on the bottom of the G2-RTU.

    • Listen for the single audible beep to confirm power connection.
    • After a few seconds:
    • Two beeps = sufficient cellular signal
    • Three beeps = insufficient cellular signal
    •  To power down, unscrew the set screw until the o-ring is visible.NEXSENS G2-Rain Alert System fig3Turn the black power set screw clockwise to apply battery using internal batteries.
  7. External power- Connect the G2-RTU adapter cable to an SP-Series solar panel or an AC power adapter.

    • Listen for the single audible beep to confirm power connection.
    • After a few seconds:
    • Two beeps = sufficient cellular signal
    • Three beeps = insufficient cellular signal
      NEXSENS G2-Rain Alert System fig2Connection of the G2-RTU external power cable and an SP-Series solar panel.

Buzzer Event

|

Beep Type

|

Status

---|---|---
When power is applied|

One short beep

|

System boot successfuul

During telemetry connection|

Two short beeps

| Connection successfully established
During telemetry connection| Three short beeps|

No signal/connection failed

For additional information, please reference the G2-RAIN Resource Library on the NexSens Knowledge Base. nexsens.com/g2rkb

937-426-2703
www.nexsens.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals