AXOR 34134000 Citterio M 3-Hole Basin Mixer 160 with Pop-Up Waste Set Instruction Manual
- June 6, 2024
- AXOR
Table of Contents
AXOR 34134000 Citterio M 3-Hole Basin Mixer 160 with Pop-Up Waste Set
Technical Information
Recommended water pressure 15 – 75 PSI
Max. water pressure 145 PSI
Recommended hot water temp. 120° – 140° F
Max. hot water temp 176°F
Flow rate 1.2 GPM
*Please know and follow all applicable local plumbing codes when setting the temperature on the water heater.
Installation Considerations
- For best results, Hansgrohe recommends that this unit be installed by a licensed, professional plumber.
- Please read over these instructions thoroughly be-fore beginning installation. Make sure that you have all tools and supplies needed to complete the installation.
- This trim is for use with rough valve 10303181 (not included).
- Keep this booklet and the receipt (or other proof of date and place of purchase) for this product in a safe place. The receipt is required should it be necessary to request warranty parts.
Tools Required
Suggested Installations
Installation
Remove the covers.
Trim the plaster shields so that they extend ¹⁄₁₆” outside the surface of the
finished wall
Seal the wall around the plaster shields with waterproof sealant.
Seal the wall around the i-box with water-proof sealant.
Failure to seal the wall can lead to pos-sible water damage.
Install the new cartridges.
- Push the extension spindle over the stem.
- Cut the extension spindle so that it extends ³⁄₁₆” outside the surface of the finished wall.
- Remove the plug from the spout port.
Thread the coupling over the stem. Cut the coupling so that it extends ¼”
outside the surface of the finished wall.
Measure the distance between the rough and the end of the plaster shield
Record this measurement (“X”). Add 1 ¾” to this measurement.
Cut the connecting thread so that it is X + 1 ¾” long.
- Install the escutcheons, nuts, color rings, and handle fixing sets.
- Wrap the threads on the connect-ing thread with plumber’s tape.
- Install the connecting thread.
- The connecting thread should extend 1⅛” outside the surface of the finished wall.
- Install the spout escutcheon. Install the spout. Tighten the screw.
- Install the handles.
- Inspect the alignment of the handles.
If it is not satisfactory, remove it, turn it slightly, and reinstall it.
- If this does not work, remove the color ring and nut.
- Remove the coupling from the nut. Turn it slightly and reinstall it.
- Reinstall the handle.
Remove the aerator. Flush the hot and cold supplies for at least 2 minutes.
Install the aerator.
Do not over-tighten the aerator.
Replacement Parts
xx = Colors / Couleurs / Acabados
00 = Chrome
82 = Brushed Nickel
User Instructions
Cleaning
Cleaning Recommendation for Hansgrohe Products
Modern bathroom faucets, kitchen faucets and shower products are made from
different materials to comply with the needs of the market with regard to
design and functionality. To avoid damage to the product, it is necessary to
take proper care of it.
For best results:
- Prevent the buildup of mineral scale and /or soap residue by cleaning your Hansgrohe product(s) when needed.
- Select a cleaning agent specifically intended for the type of product.
- Do not use these types of cleaners as they will cause damage to your Hansgrohe product:
- Any cleaning agent containing hydrochloric acid, formic acid, lye, or acetic acid.
- Abrasive cleaning powders, pads, or brushes.
- Steam cleaners.
- “No rinse” cleaning agents.
- Always follow the instructions provided by the manufacturer of the cleaning agent.
- Do not mix cleaning agents, unless directed by the manufacturer.
- Do not spray cleaners directly onto the product as drops could enter openings and gaps and cause damage. When using spray cleaners, spray the cleaner onto a soft cloth or sponge.
- Always rinse your Hansgrohe product thoroughly with clear water and polish dry with a soft cloth after cleaning. Important
- Residue from soaps, shampoos, hair dye, and other toiletries and cosmetics can cause damage. Rinse the product with clean water after each use.
- Residue from basin/tub/tile cleaner can cause damage to faucets and fittings. Immediately rinse any overspray from the Hansgrohe product.
- Do not store any cleaning agents under your Hansgrohe product, such as in a vanity unit, as the fumes may damage the product.
- Damage to the product caused by improper care or the use of improper cleaning agents is not covered by the warranty.
- If a component of the product is damaged, replace it, as there is risk of injury.
Limited Consumer Warranty
This product has been manufactured and tested to the highest quality standards by Hansgrohe, Inc. (“Hansgrohe”). This warranty is limited to Hansgrohe products that are purchased by a consumer in the United States or Canada after March 1, 1996, and installed in either the United States or in Canada.
WHO IS COVERED BY THE WARRANTY
This warranty extends to the original purchaser only. This warranty is non-
transferable.
WHAT IS COVERED BY THE WARRANTY
The warranty covers only your Hansgrohe manufactured product. Hansgrohe
warrants this product against defects in mate-rial or workmanship as follows:
Hansgrohe will replace at no charge for parts only or, at its option, replace
any product or part of the product that proves defective because of improper
workmanship and/or material, under normal installation, use, service and
maintenance. If Hansgrohe is unable to provide a replacement and repair is not
practical or cannot be made in timely fashion, Hansgrohe may elect to refund
the purchase price in exchange for the return of the product.
LENGTH OF WARRANTY
Replacement or repaired parts of products will be covered for the term of this
warranty, as stated in the following two sentences. If you are a consumer who
purchased the product for use primarily for personal, family or household
purposes, this warranty extends for as long as you own the product and the
home in which the product is originally installed. If you purchased the
product for use primarily for any other purpose, including, without
limitation, a commercial purpose, this war-ranty extends only (i) for 1 year,
with respect to Hansgrohe & Commercial products, and (ii) for 5 years, with
respect to Axor products.
THIS WARRANTY DOES NOT COVER, AND HANSGROHE WILL NOT PAY FOR:
- Conditions, malfunctions or damage not resulting from defects in material or workmanship.
- Conditions, malfunctions or damage resulting from
- normal wear and tear, improper installation, improper maintenance, misuse, abuse, negligence, accident or alteration;
- the use of abrasive or caustic cleaning agents or “no-rinse” cleaning products, or the use of the product in any manner contrary to the product instructions; or
- conditions in the home such as excessive water pressure or corrosion.
- Labor and other expenses for disconnection, deinstallation, or return of the product for warranty service (including but not limited to proper packaging and shipping costs), or for installation or reinstallation of the product.
- Accessories, connected materials and products, or related products not manufactured by Hansgrohe.
- Any Hansgrohe or Axor product sold for display purposes.
- Hansgrohe Water Filtration System is subject to a 1-year limited warranty. Warranty does not include replacement filters.
TO OBTAIN WARRANTY PARTS OR INFORMATION
Contact your Hansgrohe retailer, or contact Technical Service at:
- Hansgrohe, Inc.
- 1492 Bluegrass Lakes Parkway Alpharetta, GA 30004
- Toll-free 800-334-0455
In requesting warranty service, you will need to provide:
- The sales receipt or other evidence of the date and place of purchase.
- A description of the problem.
- Delivery of the product or the defective part, postage prepaid and carefully packed and insured, to:
- Hansgrohe, Inc.
- 1490 Bluegrass Lakes Parkway
- Alpharetta, GA 30004 Tel. 800-334-0455
- Fax 770-889-1783
www.hansgrohe-usa.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>