nubert nuPro X-3000 Compact Shelf Speaker User Guide
- June 6, 2024
- nubert
Table of Contents
QUICK START
GUIDE
nuProm X-3000 and X-4000 X compact speakers in stereo set-ups
You can find the most recent version of the operating manual here: www.nubert.de/downloads/61/
Cable connection
Master-slave connection
The speaker you connected your sources to must be set as the Master
speaker.
The master speaker controls and passes the correct
audio signal onto the second (slave-)speaker.
In order to achieve this, the speakers must be connected to each other. The
connection can be either wired or wireless. After the connection has been
made, you won’t need to make any changes to the settings on the slave-speaker.
Option A – wired connection
Connect the included coaxial cable between the orange-colored Link Out
connector on the Master speaker and the SPDIF in Coaxial 1 connector on the
Slave speaker.
The slave speaker configures itself automatically.
Option B – wireless connection
If a wired connection between the two speakers isn’t possible or wanted,
you have the option to connect the two speakers wirelessly.
Each speaker must be individually set as Master or Slave in the setup menu
of each loudspeaker. This is done using the control pad next to the display.
-
After turning on the nuPro speaker, the display will show you the set volume and input. This is the Volume sub-menu, press to return to the main menu.
-
Press 3 times to get to the setup menu.
-
Press to enter the setup menu; the display will now show pair.
-
Use the key to select either:
• wls master for your Master speaker
• wls slave for your Slave speaker
Confirm your selection with the key in the middle of the control pad. -
While establishing the connection to the other speaker, the display on each speaker will show connecting. Once the connection is established, the displays will briefly show connected and the symbol will be shown permanently in the display of the Master speaker.
Channel selection
Finally, you may have to change the default channel settings. If the left speaker is your Master speaker, you can skip this step. If your Master speaker is the right speaker you need to change the settings as follows:
- Press < to enter the main menu
- Navigate to the channel menu
- Press > to enter the channel menu and ∨ the key until the right ch is shown in the display. You don’t need to confirm the selection.
Your Master speaker will now playback the right channel. Your Slave speaker will be automatically configured to playback the left channel.
Source selection
You can now select your preferred source; the easiest way to do this is to
use the remote control.
The remote control has 6 buttons for source selection. Pressing a key
repeatedly toggles between its two sources as shown below:
|
---|---
Bluetooth
Each nuPro loudspeaker has 2 Bluetooth receivers.
The receiver marked with a headphone symbol is used for music playback.
The receiver without the headphone symbol is used for remote control purposes
and can only be accessed via the Nubert X-Remote app.
- IOS devices will show the Audio-receiver only.
- Android devices will normally show both receivers. Examples:
Stock Android 8 Samsung Experience 9
Music playback from Bluetooth devices
In order to listen to music from your Bluetooth device, you need to pair
your device with your nuPro X speaker. You only need to do this once.
On the speaker (see illustration right):
Navigate to the Bluetooth menu and enter it by pressing it . Begin pairing
by pressing .
The receiver is now visible to other Bluetooth devices.
On the transmitting device:
Go to the settings menu of your transmitter/smartphone and start the pairing
procedure (check the owner’s manual of your device). If you have an Android
device, select the receiver marked with a headphone symbol (see above).
Source selection :
Select the Bluetooth input of the nuPro speakers, either on the speaker itself
or with the remote control (see page 3).
Note:
For the best possible audio quality, set the output level of your source
device to maximum and perform all level adjustments on your nuPro speaker.
App Control: The Nubert X-Remote
Download and install the app from the Google Play Store or Apple App store.
On Android devices, you must allow access to the device’s location.
Always use the Nubert X-Remote app to connect to the master loudspeaker! Do
not use the settings menu on your device!
- After opening the app, you will be prompted to connect to a loudspeaker. Tap Connect to go to the list of available speakers. Alternatively, you can tap the home symbol in the top right corner of the screen to see available rooms or systems. Tap on the speaker you wish to control. In the app, the connection is confirmed by showing selected next to the name of the chosen speaker. On the selected speaker itself, you will see a blinking Nubert logo. Tap on the Nubert logo in the top left corner of the app to return to the main menu. If you have selected the slave-speaker, an error message will appear – simply connect to the other speaker on the list following the steps above.
- Tapping the Nubert logo toggles between the basic, daily operation of the speaker and access to the full functionality of the loudspeaker via the main menu. The latter menu is identical to that of the speaker itself.
Nubert electronic GmbH · Goethestr. 69 · D-73525 Schwäbisch Gmünd · www.nubert.de · info@nubert.de ·
Hotline: +49 7171 92690 118, Germany 0800-6823780
nuPro X-3000/4000 · Quick Start Guide E12 · 11/2019
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>